Home › Vehicle Exterior › WIPER / WASHER › RAIN SENSOR › from 2021.07
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0482415 RAIN SENSOR A

WIPER / WASHER  RAIN SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E470661N01
4,3.375 4.333,3.375 false 3.49,4.396 3.698,4.396 false 2.302,3.917 2.75,3.917 false 4.396,3.208 4.677,3.563 0.281,0.354 18 false 3 2.135,3.76 2.417,4.115 0.281,0.354 18 false 1 4.052,4.219 4.333,4.573 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 RAIN SENSOR TAPE 89944 (Click here) - -
2 RAIN SENSOR 89941 (Click here) - -
3 RAIN SENSOR COVER 89943 - - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure below is for LHD vehicles.



PROCEDURE

Hide 89944 1.INSTALL RAIN SENSOR TAPE

Z101186

HINT:
·

Only perform this procedure when replacing the rain sensor tape.

·

Replace the rain sensor tape with new one if it is damaged or contaminated.




a.
B582126C01
2.427,0.688 2.594,0.854 0.167,0.167 10 false B 2.167,0.135 2.448,0.49 0.281,0.354 18 false i 2.969,0.01 3.125,0.208 0.156,0.198 10 false A
V100155

Rain Sensor Tape - -


Standard Clearance
Measurement Area Measurement Measurement Area Measurement
A 21.8 mm (0.858 in.) B 7.25 mm (0.285 in.)

i.

Install the rain sensor tape by the below procedure.

1. Clean the sensing portion of the rain sensor with a piece of cloth.

2. Peel off the smaller release sheet, and then attach the rain sensor tape to the sensing portion of the rain sensor as shown in the illustration.

HINT:

Use your fingers to push out any air bubbles from under the tape.




Hide 89941 2.INSTALL RAIN SENSOR

a.
B582216C01
2.667,1.208 2.208,1.146 false 2.208,0.063 2.49,0.417 0.281,0.354 18 false i 2.021,1.031 2.333,1.229 0.313,0.198 10 false *a
*a Stopper - -
V100135

Push
V113147

Install in this Direction


i.

Install the rain sensor by the below procedure.

1. Clean the windshield glass with a piece of cloth.

NOTICE:
·

Make sure that there is no rain sensor tape residue remaining on the windshield glass. If there is, remove the residue.

·

If there is any rain sensor tape residue remaining on the windshield glass, replace the tape.



2. Peel off the release sheet.

HINT:
·

Perform this procedure only when installing a new rain sensor or when the rain sensor tape has been replaced.

·

Do not touch the rain sensor tape surfaces.



3. Connect the connector.

4. Gradually attach the rain sensor to the windshield glass surface as shown in the illustration to prevent air bubbles from forming between them.

HINT:

Do not touch the rain sensor tape surface or windshield glass surface.


5. Push in the stopper to install the rain sensor as shown in the illustration.



Hide 89943 3.INSTALL RAIN SENSOR COVER