Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMC Made 2WD) › from 2021.07
RM3700E _54 Brake _093728 BRAKE (REAR) _0482436 REAR BRAKE(for TMC Made 2WD) A

BRAKE (REAR)  REAR BRAKE(for TMC Made 2WD)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
C449747N02
1.198,0.198 2.198,0.365 1,0.167 1.167,0.156 2.24,0.417 1.073,0.26 5.625,4.5 5.792,4.5 5.792,4.5 5.948,4.125 false 0.771,1.417 0.771,1.167 false 4.615,3.948 4.781,3.948 4.781,3.948 4.99,3.5 false 3.552,3.583 3.719,3.583 3.719,3.583 4.031,2.979 false 1.031,1.094 1.031,0.281 1.031,0.281 1.198,0.281 false 5.292,4.427 5.563,4.646 0.271,0.219 10 false ● 4.417,3.802 4.698,4.156 0.281,0.354 18 false 4 0.698,1.417 0.979,1.771 0.281,0.354 18 false 2 3.365,3.469 3.646,3.823 0.281,0.354 18 false 3 2.573,0.125 2.854,0.479 0.281,0.354 18 false 1 3.198,3.531 3.354,3.729 0.156,0.198 10 false ● 1.26,0.219 2.229,0.49 0.969,0.271 8 false 8.3 (85, 73 in.*lbf) 5.438,4.385 5.719,4.74 0.281,0.354 18 false 5

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR DISC BRAKE BLEEDER PLUG 47547C - - -
2 REAR DISC BRAKE BLEEDER PLUG CAP 31478C - - -
3 PISTON SEAL - (Click here) - -
4 REAR DISC BRAKE PISTON 47831 (Click here) - -
5 CYLINDER BOOT - (Click here) - -

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) ● Non-reusable part
V100135

Lithium soap base glycol grease - -

CAUTION / NOTICE / HINT

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder assembly.



NOTICE:
·

Make sure not to scratch, damage or apply excessive force to any of the internal components of the rear disc brake cylinder.

·

To prevent rusting on the inside of the rear disc brake cylinder, perform the rear disc brake piston removal and installation quickly.

·

Do not clean the interior of the rear disc brake cylinder with brake cleaner.

·

Do not remove any parts unless specifically instructed to do so, and only remove the parts indicated.



PROCEDURE

Hide 47547C 1.TEMPORARILY TIGHTEN REAR DISC BRAKE BLEEDER PLUG

Z101186

HINT:

Fully tighten the rear disc brake bleeder plug after bleeding the system.



Hide 31478C 2.INSTALL REAR DISC BRAKE BLEEDER PLUG CAP

Hide 3.INSTALL PISTON SEAL

a.
C448683C02
1.833,0.063 2.188,0.365 0.354,0.302 18 true i, ii
V100155

Lithium Soap Base Glycol Grease - -


i.

Apply lithium soap base glycol grease to the entire circumference of a new piston seal.


ii.

Install the piston seal to the rear disc brake cylinder.

NOTICE:
·

Do not damage the inner surface or piston seal groove of the rear disc brake cylinder.

·

Do not allow the nut to rotate. If the nut is accidentally allowed to rotate, return it to its original position.





Hide 47831 4.INSTALL REAR DISC BRAKE PISTON

a.
C448684C02
2.667,0.479 2.958,0.479 false 2.552,1.438 2.844,1.438 false 2,2.792 1.792,2.563 1.792,2.563 2.427,2.719 true 2.438,3.146 1.875,3.281 1.875,3.281 2.021,3.146 true 1.573,0.083 1.854,0.438 0.281,0.354 18 false i 3,0.406 3.313,0.604 0.313,0.198 10 false *1 2.906,1.375 3.219,1.573 0.313,0.198 10 false *2 4.417,0.5 4.729,0.698 0.313,0.198 10 false *a 4.406,1.333 4.719,1.531 0.313,0.198 10 false *b 1.698,3.219 2.01,3.417 0.313,0.198 10 false *c 1.604,2.479 1.917,2.677 0.313,0.198 10 false (A) 4.417,0.125 4.698,0.479 0.281,0.354 18 false ii 1.333,1.906 1.896,2.26 0.563,0.354 18 false iii, iv
*1 Cylinder Boot *2 Rear Disc Brake Piston
*a Front Side *b Back Side
*c Indentations -
V100155

Lithium Soap Base Glycol Grease -


i.

Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.


ii.

Apply a light layer of lithium soap base glycol grease to the contact surfaces of the rear disc brake piston.


iii.

Install the cylinder boot to the rear disc brake piston.

NOTICE:

The front and back sides of the cylinder boot are different. Make sure not to install the cylinder boot backwards.



iv.

Install the rear disc brake piston to the rear disc brake cylinder.

NOTICE:
·

Install the rear disc brake cylinder so that its portions marked (A) fit into the indentations of the rear disc brake piston.

·

Do not forcibly install the rear disc brake piston into the rear disc brake cylinder.





Hide 5.INSTALL CYLINDER BOOT

a.
C448685C01
2.417,2.51 2.833,2.375 true 2.5,1.635 3.094,1.958 true 3.594,2.083 3.99,2.052 true 2.646,0.115 2.927,0.469 0.281,0.354 18 false i 2.323,1.563 2.635,1.76 0.313,0.198 10 false *1 2.219,2.458 2.531,2.656 0.313,0.198 10 false *2 4.042,1.979 4.354,2.177 0.313,0.198 10 false *3
*1 Cylinder Boot *2 Rear Disc Brake Cylinder Assembly
*3 Rear Disc Brake Piston - -


i.

Install the cylinder boot to the rear disc brake cylinder assembly as shown in the illustration.

NOTICE:
·

Do not damage the cylinder boot.

·

Securely install the cylinder boot into the groove of the rear disc brake cylinder assembly and groove of the rear disc brake piston.