Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMMF Made 2WD) › from 2021.07
RM3700E _54 Brake _093728 BRAKE (REAR) _0482437 REAR BRAKE(for TMMF Made 2WD) A

BRAKE (REAR)  REAR BRAKE(for TMMF Made 2WD)  DISASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (DISASSEMBLY)
C464274N01
0.927,1.135 0.927,0.885 false 3.771,3.479 3.938,3.479 3.938,3.479 4.094,3.042 false 1.292,1.323 1.292,1.073 false 4.448,3.896 4.615,3.896 4.615,3.896 5.031,3.438 false 5.479,4.385 5.646,4.385 5.646,4.385 5.917,4.125 false 5.26,4.229 5.542,4.583 0.281,0.354 18 false 1 4.219,3.729 4.5,4.083 0.281,0.354 18 false 2 0.844,1.156 1.125,1.51 0.281,0.354 18 false 4 3.563,3.323 3.844,3.677 0.281,0.354 18 false 3 1.24,1.354 1.521,1.708 0.281,0.354 18 false 5 5.115,4.292 5.271,4.49 0.156,0.198 10 false ● 3.427,3.385 3.583,3.583 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CYLINDER BOOT - (Click here) - -
2 REAR DISC BRAKE PISTON 47831 (Click here) - -
3 PISTON SEAL - (Click here) - -
4 REAR DISC BRAKE BLEEDER PLUG CAP 31478C - - -
5 REAR DISC BRAKE BLEEDER PLUG 47547C - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder assembly.

Click hereBrake>BRAKE (REAR)>REAR BRAKE (for TMMF Made 2WD)>INSTALLATION


NOTICE:
·

Make sure not to scratch, damage or apply excessive force to any of the internal components of the rear disc brake cylinder.

·

To prevent rusting on the inside of the rear disc brake cylinder, perform the rear disc brake piston removal and installation quickly.

·

Do not clean the interior of the rear disc brake cylinder with brake cleaner.

·

Do not remove any parts unless specifically instructed to do so, and only remove the parts indicated.

·

Make sure to enter pad replacement mode before removing the rear disc brake cylinder assembly.

for Gasoline Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE

for HV Model: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMMF Made)>TEST MODE PROCEDURE



PROCEDURE

Hide 1.REMOVE CYLINDER BOOT

Z101186

NOTICE:

Do not damage the inner surface or cylinder boot groove of the rear disc brake cylinder.



a.
C464275N01
1.99,0.031 2.271,0.385 0.281,0.354 18 false i

i.

Using a screwdriver with its tip wrapped with protective tape, remove the cylinder boot from the rear disc brake cylinder.



Hide 47831 2.REMOVE REAR DISC BRAKE PISTON

a.
C464276C01
2.615,1.042 2.99,1.042 false 2,0.052 3.375,0.406 1.375,0.354 18 false i, ii 2.427,0.927 2.74,1.125 0.313,0.198 10 false *a
*a Cloth - -


i.

Place a piece of cloth between the rear disc brake piston and rear disc brake cylinder.


ii.

Apply compressed air to remove the rear disc brake piston from the rear disc brake cylinder.

Z101186

CAUTION:
C464277

·

Do not hold the rear disc brake cylinder with any part of your hand between the rear disc brake cylinder and rear disc brake piston.

·

Do not place any part of your hand in front of the rear disc brake piston when using compressed air as a severe injury may result.



NOTICE:

Do not allow any brake fluid to spatter.





Hide 3.REMOVE PISTON SEAL

Z101186

NOTICE:
·

Do not damage the inner surface or piston seal groove of the rear disc brake cylinder.

·

Do not allow the nut to rotate. If the nut is accidentally allowed to rotate, return it to its original position.




a.
C464278C01
3.646,1.104 4.292,1.448 true 1.979,0.042 2.26,0.396 0.281,0.354 18 false i 4.375,1.438 4.917,1.688 0.542,0.25 10 false *a
*a Nut - -


i.

Using a screwdriver with its tip wrapped with protective tape, remove the piston seal from the rear disc brake cylinder.



Hide 31478C 4.REMOVE REAR DISC BRAKE BLEEDER PLUG CAP

a.
C464279


Hide 47547C 5.REMOVE REAR DISC BRAKE BLEEDER PLUG

a.
C464280