Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2021.07
RM3700E _59 Vehicle Exterior _092999 WIPER / WASHER _0438366 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Front Wiper Motor Circuit  


DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly through this circuit.

WIRING DIAGRAM

E437996E03
1.521,0.5 1.833,0.698 0.313,0.198 10 false A50 1.615,0.302 1.771,0.5 0.156,0.198 10 false 4 1.208,0.49 1.521,0.688 0.313,0.198 10 false +2 4.344,1.865 4.656,2.063 0.313,0.198 10 false +S 4.365,2.573 4.521,2.771 0.156,0.198 10 false E 4.063,2.49 4.427,2.719 0.365,0.229 10 false 4 4.052,0.302 4.292,0.75 0.24,0.448 10 false 3 4.063,1.771 4.313,2.177 0.25,0.406 10 false 1 3.552,1.979 3.865,2.177 0.313,0.198 10 false A43 1.521,1.26 1.833,1.458 0.313,0.198 10 false A50 1.083,1.969 1.448,2.208 0.365,0.24 10 false +SM 1.208,1.24 1.521,1.438 0.313,0.198 10 false +1 1.615,1.76 1.979,2 0.365,0.24 10 false 6 1.615,1.031 1.979,1.271 0.365,0.24 10 false 2 0.052,2.656 2.344,3.125 2.292,0.469 10 false Windshield Wiper Relay Assembly 4.344,0.396 4.656,0.594 0.313,0.198 10 false +2 4.344,1.146 4.656,1.344 0.313,0.198 10 false +1 3.646,1.771 3.896,2.177 0.25,0.406 10 false 3 3.573,2.698 3.885,2.896 0.313,0.198 10 false A43 4.448,3.115 6.635,3.74 2.188,0.625 10 false Windshield Wiper Motor Assembly 1.521,1.979 1.833,2.177 0.313,0.198 10 false A49 3.969,1.979 4.281,2.177 0.313,0.198 10 false A43 3.552,1.25 3.865,1.448 0.313,0.198 10 false A43 3.958,1.25 4.271,1.448 0.313,0.198 10 false A43 3.958,0.5 4.271,0.698 0.313,0.198 10 false A43 3.552,0.51 3.865,0.708 0.313,0.198 10 false A43 4.021,2.188 4.271,2.594 0.25,0.406 10 false *2 3.604,2.188 3.854,2.594 0.25,0.406 10 false *1 3.594,1.479 3.844,1.885 0.25,0.406 10 false *1 3.594,0.729 3.844,1.135 0.25,0.406 10 false *1 4.01,1.479 4.26,1.885 0.25,0.406 10 false *2 4.01,0.729 4.26,1.135 0.25,0.406 10 false *2 0.365,3.354 1.656,3.521 1.292,0.167 10 false *1: for LHD 1.448,3.354 2.656,3.521 1.208,0.167 10 false *2: for RHD 3.635,0.302 3.885,0.708 0.25,0.406 10 false 4 4.042,1.042 4.292,1.448 0.25,0.406 10 false 5 3.646,1.042 3.896,1.521 0.25,0.479 10 false 1 3.656,2.49 3.979,2.688 0.323,0.198 10 false 5 3.969,2.698 4.281,2.896 0.313,0.198 10 false A43 3.604,2.927 3.854,3.333 0.25,0.406 10 false *1 4.021,2.927 4.271,3.333 0.25,0.406 10 false *2

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FRONT WIPER LO OPERATION / FRONT WIPER HI OPERATION)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Wiper Lo Operation Function to operate the windshield wiper motor assembly in LO OFF or ON -
Front Wiper Hi Operation Function to operate the windshield wiper motor assembly in HI OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Lo Operation
50004 449 72
Body Electrical > Main Body > Active Test
Tester Display
Front Wiper Hi Operation
50004 449 73
OK:

Windshield wiper motor assembly operates normally.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY

OK

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the A50 and A49 windshield wiper relay assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A50,A43,A49)Location & Routing

Click Connector(A50)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

Click Connector(A43)Engine Compartment>Engine Room Main Wire>Windshield Wiper Motor Assembly

Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

A50-2 (+1) - A43-1 (+1) Always Below 1 Ω
A50-4 (+2) - A43-4 (+2) Always Below 1 Ω
A49-6 (+SM) - A43-3 (+S) Always Below 1 Ω
A50-2 (+1) or A43-1 (+1) - Body ground Always 10 kΩ or higher
A50-4 (+2) or A43-4 (+2) - Body ground Always 10 kΩ or higher
A49-6 (+SM) or A43-3 (+S) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(A50,A43,A49)Location & Routing

Click Connector(A50)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

Click Connector(A43)Engine Compartment>Engine Room Main Wire>Windshield Wiper Motor Assembly

Click Connector(A49)Instrument Panel>Engine Room Main Wire>Windshield Wiper Relay Assembly

A50-2 (+1) - A43-5 (+1) Always Below 1 Ω
A50-4 (+2) - A43-3 (+2) Always Below 1 Ω
A49-6 (+SM) - A43-1 (+S) Always Below 1 Ω
A50-2 (+1) or A43-5 (+1) - Body ground Always 10 kΩ or higher
A50-4 (+2) or A43-3 (+2) - Body ground Always 10 kΩ or higher
A49-6 (+SM) or A43-1 (+S) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition

Click Location & Routing(A43)Location & Routing

Click Connector(A43)Engine Compartment>Engine Room Main Wire>Windshield Wiper Motor Assembly

A43-5 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition

Click Location & Routing(A43)Location & Routing

Click Connector(A43)Engine Compartment>Engine Room Main Wire>Windshield Wiper Motor Assembly

A43-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR