Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for HV Model) › from 2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445204 CAN COMMUNICATION SYSTEM(for HV Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for HV Model)  Check Bus 7 Line  


DESCRIPTION

Symptom Trouble Area
There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that display communication stop history on the "Detail" screen.
·

CAN main bus line, CAN branch line or connector

·

Central gateway ECU (network gateway ECU)

·

Radio and display receiver assembly

(for Radio and Display Type with TAS Type)

·

Option connector (bus buffer ECU)

·

CAN compatible optional devices

·

No. 13 global CAN junction connector

(for TMMF Made)



WIRING DIAGRAM

for TMC Made


C434099E07
0.979,2.656 2.927,3.125 1.948,0.469 10 false Central Gateway ECU (Network Gateway ECU) 4.729,2.615 6.938,2.875 2.208,0.26 10 false Option Connector (Bus Buffer ECU) 5.083,1.542 5.594,1.719 0.51,0.177 10 false CAN+ 5.073,2.052 5.583,2.229 0.51,0.177 10 false CAN- 4.906,1.438 5.094,1.604 0.188,0.167 10 false 2 4.885,1.948 5.073,2.115 0.188,0.167 10 false 1 2.635,1.417 2.844,1.604 0.208,0.188 10 false 5 2.635,1.927 2.948,2.125 0.313,0.198 10 false 6 0.979,2.5 1.385,2.719 0.406,0.219 10 false H40 2.146,1.417 2.76,1.615 0.615,0.198 10 false CA8H 2.167,1.927 2.781,2.125 0.615,0.198 10 false CA8L 4.719,2.458 5.177,2.656 0.458,0.198 10 false H62


for TMMF Made


C430873E02
0.25,4.01 0.708,4.208 0.458,0.198 10 false H40 0.24,4.198 2.208,4.604 1.969,0.406 10 false Central Gateway ECU (Network Gateway ECU) 5.073,1.979 5.542,2.208 0.469,0.229 10 false H80 2.76,4.01 3.375,4.208 0.615,0.198 10 false H156 2.76,4.167 4.563,4.563 1.802,0.396 10 false No. 13 Global CAN Junction Connector 5.49,1.031 6.104,1.229 0.615,0.198 10 false CA8H 5.49,1.563 6.104,1.76 0.615,0.198 10 false CA8L 5.26,0.938 5.49,1.135 0.229,0.198 10 false 1 5.281,1.458 5.594,1.656 0.313,0.198 10 false 2 4.219,1.458 4.531,1.656 0.313,0.198 10 false 15 4.229,0.938 4.458,1.135 0.229,0.198 10 false 4 2.875,0.938 3.188,1.135 0.313,0.198 10 false 1 2.875,1.469 3.188,1.667 0.313,0.198 10 false 12 1.896,1.469 2.208,1.667 0.313,0.198 10 false 6 1.896,0.938 2.208,1.135 0.313,0.198 10 false 5 2.917,2.969 3.229,3.167 0.313,0.198 10 false 3 2.865,3.51 3.177,3.708 0.313,0.198 10 false 14 1.885,3.51 2.198,3.708 0.313,0.198 10 false 15 1.885,2.969 2.198,3.167 0.313,0.198 10 false 14 1.396,0.917 1.938,1.177 0.542,0.26 10 false CA8H 1.396,1.458 1.938,1.719 0.542,0.26 10 false CA8L 1.396,2.958 1.938,3.219 0.542,0.26 10 false CAXH 1.396,3.51 1.938,3.771 0.542,0.26 10 false CAXL 0.229,5.25 3.156,5.521 2.927,0.271 10 false *1: for Radio and Display Type with TAS Type 4.24,2.969 4.552,3.167 0.313,0.198 10 false 2 4.25,3.51 4.563,3.708 0.313,0.198 10 false 13 5.49,3.063 6.104,3.26 0.615,0.198 10 false CAN+ 5.49,3.615 6.104,3.813 0.615,0.198 10 false CAN- 5.073,2.167 6.802,2.563 1.729,0.396 10 false Radio and Display Receiver Assembly*1 5.073,4.021 5.542,4.25 0.469,0.229 10 false H62 5.073,4.188 6.885,4.573 1.813,0.385 10 false Option Connector (Bus Buffer ECU) 5.281,2.979 5.594,3.177 0.313,0.198 10 false 2 5.292,3.51 5.604,3.708 0.313,0.198 10 false 1


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the auxiliary battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN MAIN BUS LINES
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C425195C71
1.51,0.073 1.927,0.323 0.417,0.25 2.938,1.625 2.448,0.771 true 2.75,1.896 2.354,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.115 2.063,0.313 0.458,0.198 10 false H40 2.938,1.667 3.406,1.885 0.469,0.219 10 false CA8H 2.771,1.917 3.25,2.083 0.479,0.167 10 false CA8L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-5 (CA8H) - H40-6 (CA8L) Cable disconnected from negative (-) auxiliary battery terminal Below 70 Ω



Result:
Result
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS LINES

NG

41.CHECK VEHICLE TYPE
2.CHECK FOR SHORT IN CAN BUS LINES
a.
C425195C71
1.51,0.073 1.927,0.323 0.417,0.25 2.938,1.625 2.448,0.771 true 2.75,1.896 2.354,0.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 1.604,0.115 2.063,0.313 0.458,0.198 10 false H40 2.938,1.667 3.406,1.885 0.469,0.219 10 false CA8H 2.771,1.917 3.25,2.083 0.479,0.167 10 false CA8L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-5 (CA8H) - H40-6 (CA8L) Cable disconnected from negative (-) auxiliary battery terminal 54 Ω or higher



Result:
Result
OK
NG



OK

3.CHECK FOR SHORT TO +B IN CAN BUS LINE

NG

29.CHECK VEHICLE TYPE
3.CHECK FOR SHORT TO +B IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C51
1.844,0.198 2.313,0.448 0.469,0.25 5.313,0.292 5.729,0.563 0.417,0.271 2.802,1.208 3.24,1.958 true 6.51,1.927 6.302,1.604 true 2.719,1.198 2.969,2.125 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 2.969,2.167 3.521,2.365 0.552,0.198 10 false CA8L 6.51,1.958 7.063,2.156 0.552,0.198 10 false BAT 3.25,1.969 3.802,2.167 0.552,0.198 10 false CA8H 5.427,0.344 5.74,0.542 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-5 (CA8H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-6 (CA8L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS LINE

NG

17.CHECK VEHICLE TYPE
4.CHECK FOR SHORT TO GND IN CAN BUS LINE
a.

Measure the resistance according to the value(s) in the table below.

C430911C52
1.823,0.198 2.292,0.448 0.469,0.25 5.313,0.146 5.729,0.417 0.417,0.271 4.958,0.625 5.385,1.042 true 2.719,1.208 3.052,2.24 true 2.813,1.198 3.323,1.958 true 3.958,0.354 4.271,0.552 0.313,0.198 10 false *1 1.958,0.25 2.354,0.448 0.396,0.198 10 false H40 3.063,2.26 3.625,2.458 0.563,0.198 10 false CA8L 4.708,0.5 5.26,0.698 0.552,0.198 10 false CG 3.344,1.969 3.896,2.167 0.552,0.198 10 false CA8H 5.438,0.208 5.75,0.406 0.313,0.198 10 false H3 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-5 (CA8H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-6 (CA8L) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

5.CHECK VEHICLE TYPE
5.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

6.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
6.CHECK FOR SHORT TO GND IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-5 (CA8H) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Opinion Connector (Bus Buffer ECU)
H40-6 (CA8L) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

7.CHECK FOR SHORT TO GND IN CAN BUS LINE (OPTION CONNECTOR (BUS BUFFER ECU))
7.CHECK FOR SHORT TO GND IN CAN BUS LINE (OPTION CONNECTOR (BUS BUFFER ECU))
a.

Disconnect the H62 option connector (bus buffer ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H62,H3)Location & Routing

Click Connector(H62)Instrument Panel>Instrument Panel Wire / Speaker Wire>Option Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H62-2 (CAN+) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H62-1 (CAN-) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPAIR OR REPLACE CAN COMPATIBLE OPTIONAL DEVICES

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (OPTION CONNECTOR (BUS BUFFER ECU) - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

8.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H156 No. 13 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H156-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
9.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H156-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

10.CHECK VEHICLE TYPE

NG

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
10.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for Radio and Display Type with TAS Type A
except Radio and Display Type with TAS Type B



A

11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
11.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Radio and Display Receiver Assembly
H156-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))

NG

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
12.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Option Connector (Bus Buffer ECU)
H156-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR

NG

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
13.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-1 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H156-12 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

14.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-3 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Central Gateway ECU (Network Gateway ECU)
H156-14 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

15.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-4 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Radio and Display Receiver Assembly
H156-15 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

16.CHECK FOR SHORT TO GND IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
a.

Disconnect the H62 option connector (bus buffer ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-2 (CANH) - H3-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Option Connector (Bus Buffer ECU)
H156-13 (CANL) - H3-4 (CG)



Result:
Result
OK
NG



OK

REPAIR OR REPLACE CAN COMPATIBLE OPTIONAL DEVICES

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))

17.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

18.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
18.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40,H3)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H40-5 (CA8H) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Option Connector (Bus Buffer ECU)
H40-6 (CA8L) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

19.CHECK FOR SHORT TO +B IN CAN BUS LINE (OPTION CONNECTOR (BUS BUFFER ECU))
19.CHECK FOR SHORT TO +B IN CAN BUS LINE (OPTION CONNECTOR (BUS BUFFER ECU))
a.

Disconnect the H62 option connector (bus buffer ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H62,H3)Location & Routing

Click Connector(H62)Instrument Panel>Instrument Panel Wire / Speaker Wire>Option Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H62-2 (CAN+) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H62-1 (CAN-) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPAIR OR REPLACE CAN COMPATIBLE OPTIONAL DEVICES

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (OPTION CONNECTOR (BUS BUFFER ECU) - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

20.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H156 No. 13 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H156-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

21.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
21.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H156-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

22.CHECK VEHICLE TYPE

NG

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
22.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for Radio and Display Type with TAS Type A
except Radio and Display Type with TAS Type B



A

23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
23.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Radio and Display Receiver Assembly
H156-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))

NG

27.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
24.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Option Connector (Bus Buffer ECU)
H156-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR

NG

28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
25.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-1 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H156-12 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

26.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-3 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Central Gateway ECU (Network Gateway ECU)
H156-14 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

27.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-4 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Radio and Display Receiver Assembly
H156-15 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

28.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
a.

Disconnect the H62 option connector (bus buffer ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156,H3)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H3)Instrument Panel>Instrument Panel Wire / Speaker Wire>DLC3

H156-2 (CANH) - H3-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher to Option Connector (Bus Buffer ECU)
H156-13 (CANL) - H3-16 (BAT)



Result:
Result
OK
NG



OK

REPAIR OR REPLACE CAN COMPATIBLE OPTIONAL DEVICES

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))

29.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

30.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

32.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
30.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-5 (CA8H) - H40-6 (CA8L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Option Connector (Bus Buffer ECU)



Result:
Result
OK
NG



OK

NG

31.CHECK FOR SHORT IN CAN BUS LINES (OPTION CONNECTOR (BUS BUFFER ECU))
31.CHECK FOR SHORT IN CAN BUS LINES (OPTION CONNECTOR (BUS BUFFER ECU))
a.

Disconnect the H62 option connector (bus buffer ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H62)Location & Routing

Click Connector(H62)Instrument Panel>Instrument Panel Wire / Speaker Wire>Option Connector

H62-2 (CAN+) - H62-1 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

REPAIR OR REPLACE CAN COMPATIBLE OPTIONAL DEVICES

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (OPTION CONNECTOR (BUS BUFFER ECU) - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

32.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H156 No. 13 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-1 (CANH) - H156-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

33.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

37.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
33.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-3 (CANH) - H156-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

34.CHECK VEHICLE TYPE

NG

38.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
34.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for Radio and Display Type with TAS Type A
except Radio and Display Type with TAS Type B



A

35.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

36.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
35.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-4 (CANH) - H156-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Radio and Display Receiver Assembly



Result:
Result
OK
NG



OK

36.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))

NG

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
36.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-2 (CANH) - H156-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher to Option Connertor (Bus Buffer ECU)



Result:
Result
OK
NG



OK

REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR

NG

40.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
37.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-1 (CANH) - H156-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Option Connector (Bus Buffer ECU)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

38.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-3 (CANH) - H156-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Central Gateway ECU (Network Gateway ECU)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

39.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the H80 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-4 (CANH) - H156-15 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Radio and Display Receiver Assembly



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - RADIO AND DISPLAY RECEIVER ASSEMBLY)

40.CHECK FOR SHORT IN CAN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))
a.

Disconnect the H62 option connector (bus buffer ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-2 (CANH) - H156-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher to Option Connector (Bus Buffer ECU)



Result:
Result
OK
NG



OK

REPAIR OR REPLACE CAN COMPATIBLE OPTIONAL DEVICES

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - OPTION CONNECTOR (BUS BUFFER ECU))

41.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for TMC Made A
for TMMF Made B



A

42.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

44.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
42.CHECK FOR OPEN IN CAN MAIN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H40)Location & Routing

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H40-5 (CA8H) - H40-6 (CA8L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

43.CHECK FOR OPEN IN CAN MAIN BUS LINES (OPTION CONNECTOR (BUS BUFFER ECU))
43.CHECK FOR OPEN IN CAN MAIN BUS LINES (OPTION CONNECTOR (BUS BUFFER ECU))
a.

Disconnect the H62 option connector (bus buffer ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H62)Location & Routing

Click Connector(H62)Instrument Panel>Instrument Panel Wire / Speaker Wire>Option Connector

H62-2 (CAN+) - H62-1 (CAN-) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPAIR OR REPLACE CAN COMPATIBLE OPTIONAL DEVICES

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (OPTION CONNECTOR (BUS BUFFER ECU) - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

44.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H156 No. 13 global CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-1 (CANH) - H156-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

45.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

NG

46.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
45.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H156)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

H156-3 (CANH) - H156-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE NO. 13 GLOBAL CAN JUNCTION CONNECTOR

NG

47.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
46.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H156,H40)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H156-1 (CANH) - H40-5 (CA8H) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H156-12 (CANL) - H40-6 (CA8L)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

47.CHECK FOR OPEN IN CAN MAIN BUS LINES (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H156,H40)Location & Routing

Click Connector(H156)Instrument Panel>Instrument Panel Wire / Speaker Wire>No. 13 Global CAN Junction Connector

Click Connector(H40)Instrument Panel>Instrument Panel Wire / Speaker Wire>Network Gateway ECU

H156-3 (CANH) - H40-14 (CAXH) Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H156-14 (CANL) - H40-15 (CAXL)



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 13 GLOBAL CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))