Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › from 2021.07
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440164 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B590928N02
1.74,4.771 1.823,5.083 1.823,5.083 1.99,5.083 false 1.01,4.927 1.198,5.292 1.198,5.292 1.365,5.292 false 3.719,5.083 3.719,5.365 false 6.729,4.229 6.729,5.083 false 6.115,2.5 6.406,2.5 false 2.042,4.927 2.229,5.229 0.188,0.302 18 false 1 1.667,5.156 1.854,5.458 0.188,0.302 18 false 3 3.781,5.365 3.969,5.667 0.188,0.302 18 false 5 6.771,5.073 6.958,5.375 0.188,0.302 18 false 4 6.458,2.354 6.646,2.656 0.188,0.302 18 false 2 3.594,4.135 3.792,4.302 0.198,0.167 10 false x2 4.698,5.396 4.896,5.563 0.198,0.167 10 false x3 1.063,5.365 1.385,5.573 0.323,0.208 10 false x2 0.833,3.906 1.115,4.156 0.281,0.25 10 false x2 4.771,2.698 5.135,3 0.365,0.302 10 false x2 6.344,4.865 6.656,5.125 0.313,0.26 10 false x2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 REAR BUMPER SIDE SEAL LH 52592 - - -
2 REAR BUMPER SIDE SEAL RH 52591 - - -
3 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH 75606B (Click here) - -
4 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY RH 75605B (Click here) - -
5 REAR BUMPER ASSEMBLY - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear bumper assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
w/ Parking Support Brake System:

Rear bumper assembly (Including removal and installation)


·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

TOYOTA parking assist-sensor system (w/ Parking Support Brake System)

·

Parking support brake system

·

Advanced Park (w/ Advanced Park)


w/o Advanced Park:(Click here)
w/ Advanced Park:(Click here)

PROCEDURE

Hide 52592 1.REMOVE REAR BUMPER SIDE SEAL LH

a.
B590930


Hide 52591 2.REMOVE REAR BUMPER SIDE SEAL RH

a.

Use the same procedure as for the LH side.


Hide 75606B 3.SEPARATE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH

a.
B590931C02
0.365,0.125 0.552,0.448 0.188,0.323 18 false i 3.635,0.094 3.885,0.417 0.25,0.323 18 false ii 0.375,1.979 0.656,2.302 0.281,0.323 18 false iii 2,2.042 2.281,2.365 0.281,0.323 18 false iv
V113146

Place Hand Here
V113147

Remove in this Direction


i.

Apply protective tape around the quarter outside moulding sub-assembly LH.


ii.

Remove the screw.


iii.

Disengage the claws by pushing the area indicated by the arrow in the illustration with a finger.

NOTICE:

To avoid damaging the claws, do not forcibly pull the quarter outside moulding sub-assembly LH.



iv.

Disengage the clips to separate the quarter outside moulding sub-assembly LH from the rear bumper assembly.



Hide 75605B 4.SEPARATE QUARTER OUTSIDE MOULDING SUB-ASSEMBLY RH

a.

Use the same procedure as for the LH side.


Hide 5.REMOVE REAR BUMPER ASSEMBLY

a.
B590071N02
0.354,0.115 0.49,0.438 0.135,0.323 18 false i 0.354,2.427 0.594,2.75 0.24,0.323 18 false ii 3.875,3.75 4.177,4.073 0.302,0.323 18 false iii

i.

Apply protective tape around the rear bumper assembly.


ii.

Remove the 2 rear bumper cushions.


iii.

Remove the 3 clips.



b.
B590072C03
5.5,2.021 5.719,2.292 0.219,0.271 18 false iii 1.906,1.969 2.125,2.26 0.219,0.292 18 false ii 5.208,2.073 5.5,2.333 0.292,0.26 12 false *A 0.375,0.104 0.594,0.427 0.219,0.323 18 false i
*A w/ Wire Harness - -
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


i.

Disengage the claws as shown in the illustration.


ii.

Disengage the claws to remove the rear bumper assembly as shown in the illustration.


iii.

w/ Wire Harness:

1. Disconnect the connector.