Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › WHEEL OPENING MOULDING (for Front) › from 2021.07
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440183 WHEEL OPENING MOULDING(for Front) A

EXTERIOR PANELS / TRIM  WHEEL OPENING MOULDING(for Front)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
B614731N01
2.333,0.167 6.083,1.833 3.75,1.667 3.333,3.083 4.583,3.917 1.25,0.833 5,1.25 5.333,1.25 false 5.042,2.833 5.375,2.833 false 4.146,3.573 4.323,3.573 false 3.042,3.927 3.042,4.26 false 3.958,3.396 4.24,3.75 0.281,0.354 18 false 1 5.833,1.073 6.115,1.427 0.281,0.354 18 false 2 2.969,4.271 3.25,4.625 0.281,0.354 18 false 3 5.448,2.729 5.76,2.927 0.313,0.198 10 false *1 2.375,0.198 2.75,0.438 0.375,0.24 12 false *A 3.375,3.094 3.75,3.333 0.375,0.24 12 false *A 3.823,3.438 4.135,3.635 0.313,0.198 10 false ● 5.698,1.156 6.01,1.354 0.313,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 NO. 1 FRONT WHEEL OPENING EXTENSION PAD 53851G (Click here) - -
2 FRONT WHEEL OPENING EXTENSION PAD 53851D (Click here) - -
3 FRONT FENDER LINER RETAINER 53879A - - -

*A for TMC Made - -
*1 FRONT FENDER MOULDING - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 53851G 1.INSTALL NO. 1 FRONT WHEEL OPENING EXTENSION PAD (for TMC Made)

Z101186

NOTICE:

When installing a new No. 1 front wheel opening extension pad, heat the front fender moulding using a heat light.



Standard:
Item Temperature
Front Fender Moulding 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front fender moulding excessively.


a.
B590985C03
3.948,2.156 3.844,2.021 false 4.01,2.354 3.979,2.188 false 5.354,2.333 5.292,2.198 false 5.24,2.156 5.125,2.104 false 3.75,1.875 4.063,2.031 0.313,0.156 10 false *a 4.958,1.99 5.271,2.146 0.313,0.156 10 false *a 3.969,2.375 4.281,2.531 0.313,0.156 10 false *a 5.323,2.344 5.635,2.5 0.313,0.156 10 false *a 0.552,0.667 0.75,1.01 0.198,0.344 18 false i 3.656,0.135 4.229,0.469 0.573,0.333 18 false ii
*a Location Line - -


i.

Clean the front fender moulding.

1. Using a heat light, heat the front fender moulding surface.

2. Remove any remaining double-sided tape from the front fender moulding.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the No. 1 front wheel opening extension pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new No. 1 front wheel opening extension pad.

1. Using a heat light, heat the front fender moulding.

2. Remove the release paper from the No. 1 front wheel opening extension pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the No. 1 front wheel opening extension pad as shown in the illustration.

HINT:
·

Make sure that the end of the No. 1 front wheel opening extension pad is between the location lines.

·

Press the No. 1 front wheel opening extension pad firmly to install it.





Hide 53851D 2.INSTALL FRONT WHEEL OPENING EXTENSION PAD (for TMC Made)

Z101186

NOTICE:

When installing a new front wheel opening extension pad, heat the front fender moulding using a heat light.



Standard:
Item Temperature
Front Fender Moulding 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front fender moulding excessively.


a.
B590986C03
3.875,1.927 4.01,2.042 false 3.875,2.219 4.01,2.115 false 6.229,1.073 6.271,1.24 false 6.333,1.26 6.479,1.177 false 3.75,1.781 4.063,1.938 0.313,0.156 10 false *a 6.115,0.927 6.427,1.083 0.313,0.156 10 false *a 3.76,2.208 4.073,2.365 0.313,0.156 10 false *a 6.458,1.042 6.771,1.198 0.313,0.156 10 false *a 0.552,0.667 0.75,1.01 0.198,0.344 18 false i 3.646,0.135 4.219,0.438 0.573,0.302 18 false ii
*a Location Line - -


i.

Clean the front fender moulding.

1. Using a heat light, heat the front fender moulding surface.

2. Remove any remaining double-sided tape from the front fender moulding.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front wheel opening extension pad with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new front wheel opening extension pad.

1. Using a heat light, heat the front fender moulding.

2. Remove the release paper from the front wheel opening extension pad.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the front wheel opening extension pad as shown in the illustration.

HINT:
·

Make sure that the end of the front wheel opening extension pad is between the location lines.

·

Press the front wheel opening extension pad firmly to install it.





Hide 53879A 3.INSTALL FRONT FENDER LINER RETAINER