Home › Vehicle Interior › HEATING / AIR CONDITIONING › BLOWER UNIT › from 2021.07
RM3700E _58 Vehicle Interior _093020 HEATING / AIR CONDITIONING _0438489 BLOWER UNIT A

HEATING / AIR CONDITIONING  BLOWER UNIT  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
I117521N01
0.219,0.042 4.698,2.635 4.479,2.594 4.177,2.667 6.917,3.625 2.74,0.958 4.698,1.344 5.031,1.344 false 2.365,3.208 2.802,3.208 false 3.281,1.51 3.281,1.844 false 5.594,2.927 5.594,3.26 false 5.083,1.167 5.365,1.521 0.281,0.354 18 false 1 3.229,1.896 3.51,2.25 0.281,0.354 18 false 4 4.021,1.635 4.333,1.833 0.313,0.198 10 false x2 2.125,3.073 2.406,3.427 0.281,0.354 18 false 2 4.25,2.729 4.625,2.969 0.375,0.24 12 false *A 5.531,3.281 5.813,3.635 0.281,0.354 18 false 3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 AIR CONDITIONER UNIT ASSEMBLY - - - -
2 NO. 2 AIR DUCT 87211A (Click here) - -
3 NO. 3 INSTRUMENT PANEL WIRE 82143C - - -
4 BLOWER ASSEMBLY 87130D - - -

*A for Cold Area Specification Vehicles - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the blower unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)
No. 1 blower damper servo sub-assembly Initialize servo motor (Air Conditioning System) DTCs are stored for Gasoline Model:(Click here)
for HV Model:(Click here)

HINT:
·

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for LHD and RHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 87211A 2.REMOVE NO. 2 AIR DUCT

Z101186

Click here(Click here)

Hide 82143C 3.REMOVE NO. 3 INSTRUMENT PANEL WIRE (for Cold Area Specification Vehicles)

a.
I117522


Hide 87130D 4.REMOVE BLOWER ASSEMBLY

a.
I117523C01
0.167,0.083 0.542,0.323 0.375,0.24 12 false *A 0.146,2 0.521,2.24 0.375,0.24 12 false *B
*A for Manual Air Conditioning System *B for Automatic Air Conditioning System