|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
|
for Gasoline Model (for HFC-134a(R134a)):
Compressor oil ND-OIL 8 or equivalent for Gasoline Model (for HFO-1234yf(R1234yf)): Compressor oil ND-OIL 12 or equivalent for HV Model: Compressor oil ND-OIL 11 or equivalent |
- | - |
884A0
1.INSTALL COOLER CONDENSER ASSEMBLY
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides and claws to install the cooler condenser assembly as shown in the illustration.
Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.
If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.
Add 40 cc (1.35 fl.oz)
for Gasoline Model (HFC-134a(R134a)):
ND-OIL 8 or equivalent
for Gasoline Model (HFO-1234yf(R1234yf)):
ND-OIL 12 or equivalent
for HV Model:
ND-OIL 11 or equivalent
88710E
2.INSTALL AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
Remove the vinyl tape from the air conditioning tube and accessory assembly and cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the air conditioner tube and accessory assembly.
for Gasoline Model (HFC-134a(R134a)):
ND-OIL 8 or equivalent
for Gasoline Model (HFO-1234yf(R1234yf)):
ND-OIL 12 or equivalent
for HV Model:
ND-OIL 11 or equivalent
Install the O-ring to the air conditioning tube and accessory assembly.
Keep the O-rings and O-ring fitting surfaces free from foreign matter.
Connect the air conditioning tube and accessory assembly to the cooler condenser assembly with the bolt.
88711
3.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the vinyl tape from the No. 1 cooler refrigerant discharge hose and cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the No. 1 cooler refrigerant discharge hose.
for Gasoline Model (HFC-134a(R134a)):
ND-OIL 8 or equivalent
for Gasoline Model (HFO-1234yf(R1234yf)):
ND-OIL 12 or equivalent
for HV Model:
ND-OIL 11 or equivalent
Install the O-ring to the No. 1 cooler refrigerant discharge hose.
Keep the O-rings and O-ring fitting surfaces free from foreign matter.
Connect the No. 1 cooler refrigerant discharge hose to the cooler condenser assembly with the bolt.
53036C
4.INSTALL FRONT END PANEL MOUNTING BRACKET SUB-ASSEMBLY LH
53035C
5.INSTALL FRONT END PANEL MOUNTING BRACKET SUB-ASSEMBLY RH
16595D
6.INSTALL NO. 1 RADIATOR AIR GUIDE LH
16561D
7.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
16562L
8.INSTALL NO. 2 RADIATOR TO SUPPORT SEAL
16681A
9.INSTALL RADIATOR UPPER AIR GUIDE PLATE
52131A
10.INSTALL FRONT BUMPER REINFORCEMENT
52611
11.INSTALL FRONT BUMPER ENERGY ABSORBER
53510
12.INSTALL HOOD LOCK ASSEMBLY
86520
13.INSTALL LOW PITCHED HORN ASSEMBLY
Click hereVehicle Exterior>HORN>HORN>INSTALLATION
14.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
15. WARM UP ENGINE (for Gasoline Model)
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
16.WARM UP COMPRESSOR (for HV Model)
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT
17.INSPECT FOR REFRIGERANT LEAK
for HFC-134a(R134a):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFC-134a(R134a))>REPLACEMENT
for HFO-1234yf(R1234yf):
Click hereVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT