Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0438555 ULTRASONIC SENSOR(for Rear) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E463470N02
1.521,1.958 1.979,1.958 false 1.323,1.833 1.604,2.188 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 ULTRASONIC SENSOR CUSHION SET - (Click here) - -

E449667N04
5.5,0.531 7.01,1.844 1.51,1.313 0.427,4.031 2.063,5.521 1.635,1.49 1.458,3.667 1.802,3.667 false 1.271,1.531 1.604,1.531 false 5.333,4.958 5.333,5.292 false 1.188,4.677 1.302,4.917 1.302,4.917 1.458,4.917 false 0.74,4.938 0.74,5.073 false 2.24,0.979 2.573,0.979 false 0.375,2.76 0.708,2.76 false 1.667,2.052 1.99,2.052 false 2.896,0.479 3.229,0.479 false 6.135,0.865 6.26,0.865 6.26,0.865 6.375,1.208 false 6.448,0.292 6.708,0.292 false 3.333,1.896 3.583,1.896 false 0.708,3.208 1.042,3.208 false 6.667,1.208 6.667,1.354 false 1.229,4.24 1.365,4.24 1.365,4.24 1.51,4.375 false 6.094,1.385 6.094,1.531 false 3.625,1.01 3.625,1.281 false 4.427,1.469 4.427,1.74 false 5.281,5.313 5.563,5.604 0.281,0.292 18 false 9 1.677,1.375 1.958,1.729 0.281,0.354 18 false 5 2.625,0.823 2.906,1.177 0.281,0.354 18 false 5 3.583,1.292 3.865,1.646 0.281,0.354 18 false 6 0.51,3.052 0.792,3.406 0.281,0.354 18 false 6 1.281,3.521 1.563,3.875 0.281,0.354 18 false 3 4.615,1.76 4.896,2.115 0.281,0.354 18 false 3 3.156,1.75 3.438,2.104 0.281,0.354 18 false 2 1.49,1.906 1.771,2.26 0.281,0.354 18 false 2 1.323,1.99 1.604,2.344 0.281,0.354 10 false ● 1.146,3.552 1.427,3.906 0.281,0.354 10 false ● 2.99,1.833 3.177,2.083 0.188,0.25 10 false ● 4.49,1.792 4.771,2.146 0.281,0.354 10 false ● 6.688,1.375 6.865,1.656 0.177,0.281 10 false ● 6.823,1.354 6.958,1.635 0.135,0.281 18 false 4 5.979,0.729 6.26,1.083 0.281,0.354 18 false 7 1.5,4.781 1.781,5.135 0.281,0.354 18 false 7 1.052,5.063 1.333,5.417 0.281,0.354 18 false 4 0.906,5.083 1.083,5.302 0.177,0.219 10 false ● 5.573,0.573 5.948,0.813 0.375,0.24 12 false *A 0.5,4.073 0.875,4.313 0.375,0.24 12 false *A 5.031,0.115 5.448,0.469 0.417,0.354 18 false 10 3.292,0.323 3.573,0.677 0.281,0.354 18 false 8 0.74,2.615 1.021,2.969 0.281,0.354 18 false 8 6.021,1.531 6.302,1.885 0.281,0.354 18 false 8 1.073,4.094 1.354,4.448 0.281,0.354 18 false 8 5.344,0.167 5.76,0.427 0.417,0.26 12 false (*B) 5.646,0.115 6.292,0.708 0.646,0.594 18 false , 11 6.083,0.188 6.5,0.448 0.417,0.26 12 false (*C)

Procedure Part Name Code
Z101186

Z101188

Z101187

2 REAR CENTER ULTRASONIC SENSOR RETAINER 89C48B (Click here) - -
3 REAR CORNER ULTRASONIC SENSOR RETAINER 89C48A (Click here) - -
4 REAR SIDE ULTRASONIC SENSOR RETAINER 89C48C (Click here)
5 REAR CENTER ULTRASONIC SENSOR 89342A - - -
6 REAR CORNER ULTRASONIC SENSOR 89342 - - -
7 REAR SIDE ULTRASONIC SENSOR 89342B - - -
8 ULTRASONIC SENSOR CLIP 89348D - - -
9 REAR BUMPER ASSEMBLY - - - -
10 PERFORM CALIBRATION - - - (Click here)
11 PERFORM CALIBRATION - - - (Click here)

*A w/ Advanced Park *B w/ Parking Support Brake System
*C w/o Parking Support Brake System - -
● Non-reusable part - -

PROCEDURE

Hide 1.INSTALL ULTRASONIC SENSOR CUSHION SET

Z101186

NOTICE:

Perform this procedure only when replacement of the ultrasonic sensor cushion set is necessary.



Hide 89C48B 2.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

Z101186

NOTICE:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

If a rear center ultrasonic sensor retainer has been removed, replace it with a new one.




a.
E449660C01
4.281,5.563 4.021,5.365 true 2.698,3.563 2.438,3.365 true 0.365,0.156 0.646,0.51 0.281,0.354 18 true i 4.729,0.146 5.01,0.5 0.281,0.354 18 false ii 4.427,2.083 4.708,2.438 0.281,0.354 18 false iv 0.406,1.99 0.615,2.26 0.208,0.271 18 true iii 4.865,5.469 5.115,5.75 0.25,0.281 18 true v 4.302,5.51 4.49,5.688 0.188,0.177 10 true *a 2.698,3.479 2.885,3.656 0.188,0.177 10 true *a
*a Scribed Line - -
V100144

Primer Application - -


i.

Clean the surface of the rear bumper assembly.

1. Using a heat light, heat the rear bumper assembly.

1. Remove any remaining double-sided tape from the rear bumper assembly.

3. Wipe off any adhesive residue with cleaner.

NOTICE:
·

Installing the rear center ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Cover the sensor installation hole with a 20 mm (0.787 in.) circular piece of tape.


iii.

Apply primer to rear bumper assembly on the installation area of the rear center ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear center ultrasonic sensor retainer has been attached.



1. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))


2. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


iv.

Remove the peeling paper of a new rear center ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



v.

Align the rear center ultrasonic sensor retainer with rear center ultrasonic sensor with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the rear center ultrasonic sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

The application strength of the rear center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

·

Apply pressure so that it does not lift up from the rear bumper assembly.



HINT:

Pushing force: 50 N (5.1 kgf) for 3 seconds




b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 89C48A 3.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

Z101186

NOTICE:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one.




a.
E449660C01
4.281,5.563 4.021,5.365 true 2.698,3.563 2.438,3.365 true 0.365,0.156 0.646,0.51 0.281,0.354 18 true i 4.729,0.146 5.01,0.5 0.281,0.354 18 false ii 4.427,2.083 4.708,2.438 0.281,0.354 18 false iv 0.406,1.99 0.615,2.26 0.208,0.271 18 true iii 4.865,5.469 5.115,5.75 0.25,0.281 18 true v 4.302,5.51 4.49,5.688 0.188,0.177 10 true *a 2.698,3.479 2.885,3.656 0.188,0.177 10 true *a
*a Scribed Line - -
V100144

Primer Application - -


i.

Clean the surface of the rear bumper assembly.

1. Using a heat light, heat the rear bumper assembly.

1. Remove any remaining double-sided tape from the rear bumper assembly.

3. Wipe off any adhesive residue with cleaner.

NOTICE:
·

Installing the rear corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Cover the sensor installation hole with a 20 mm (0.787 in.) circular piece of tape.


iii.

Apply primer to rear bumper assembly on the installation area of the rear corner ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear corner ultrasonic sensor retainer has been attached.



1. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))


2. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


iv.

Remove the peeling paper of a new rear corner ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



v.

Align the rear corner ultrasonic sensor retainer with rear corner ultrasonic sensor with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the rear corner ultrasonic sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

The application strength of the rear corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

·

Apply pressure so that it does not lift up from the rear bumper assembly.



HINT:

Pushing force: 50 N (5.1 kgf) for 3 seconds




b.

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


Hide 89C48C 4.INSTALL REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Advanced Park)

Z101186

NOTICE:
·

Perform this procedure only when replacement of the rear side ultrasonic sensor retainer is necessary.

·

If a rear side ultrasonic sensor retainer has been removed, replace it with a new one.




a.
E449671C02
1.208,3.417 1.5,3.219 true 2.188,5.5 2.552,5.615 2.552,5.615 2.469,5.51 true 1.479,4.667 1.25,4.594 true 4.74,4.344 4.552,4.24 4.552,4.24 5.042,4.333 true 5.854,5.604 5.677,5.531 true 0.344,0.167 0.583,0.469 0.24,0.302 18 true i 0.333,1.979 0.573,2.281 0.24,0.302 18 true iii 4.74,0.146 4.979,0.448 0.24,0.302 18 false ii 4.448,2.073 4.729,2.417 0.281,0.344 18 false iv 1.042,3.427 1.281,3.625 0.24,0.198 10 true *a 2.583,5.552 2.792,5.708 0.208,0.156 10 true *b 0.958,4.146 1.208,4.427 0.25,0.281 18 true vi 1.031,4.479 1.24,4.667 0.208,0.188 10 true *a 3.115,5.49 3.302,5.781 0.188,0.292 18 true v 4.635,3.781 4.823,4.073 0.188,0.292 18 true v 4.344,4.156 4.552,4.313 0.208,0.156 10 true *b 5.865,5.521 6.073,5.708 0.208,0.188 10 true *a 6.417,5.469 6.667,5.75 0.25,0.281 18 true vi 0.427,4.073 0.708,4.292 0.281,0.219 12 true *A 3.917,4.094 4.198,4.313 0.281,0.219 12 true *B
*A for LH Side *B for RH Side
*a Scribed Line *b Identification Code
V100144

Primer Application - -


i.

Clean the surface of the rear bumper assembly.

1. Using a heat light, heat the rear bumper assembly.

1. Remove any remaining double-sided tape from the rear bumper assembly.

3. Wipe off any adhesive residue with cleaner.

NOTICE:
·

Installing the rear side ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Cover the sensor installation hole with a 20 mm (0.787 in.) circular piece of tape.


iii.

Apply primer to rear bumper assembly on the installation area of the rear side ultrasonic sensor retainer using a brush or felt.

NOTICE:
·

Replace the brush or felt if it is dirty or has become hardened.

·

Keep any painted surface free from primer.

·

If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.

·

Do not touch surfaces to which primer has been applied until the rear side ultrasonic sensor retainer has been attached.



1. Let the primer dry sufficiently.

NOTICE:

Do not touch applied surfaces until the primer is dry.


Recommended drying time:

10 minutes or more (at 23°C (73°F))


2. Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


iv.

Remove the peeling paper of a new rear side ultrasonic sensor retainer trying not to touch the adhesional surface.

NOTICE:

After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work gloves.



v.

Check that the identification codes on the rear bumper assembly and the rear side ultrasonic sensor retainer are identical.


vi.

Align the rear side ultrasonic sensor retainer with rear side ultrasonic sensor with the scribed line on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the rear side ultrasonic sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

The application strength of the rear side ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.

·

Apply pressure so that it does not lift up from the rear bumper assembly.



HINT:

Pushing force: 50 N (5.1 kgf) for 3 seconds




Hide 89342A 5.INSTALL REAR CENTER ULTRASONIC SENSOR

Hide 89342 6.INSTALL REAR CORNER ULTRASONIC SENSOR

Hide 89342B 7.INSTALL REAR SIDE ULTRASONIC SENSOR (w/ Advanced Park)

Hide 89348D 8.INSTALL ULTRASONIC SENSOR CLIP

Hide 9.INSTALL REAR BUMPER ASSEMBLY

Hide 10.PERFORM CALIBRATION (w/ Parking Support Brake System)