Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › from 2021.07
RM3700E _57 Power Source / Network _093028 POWER DISTRIBUTION _0483098 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
E471028N01
4.917,1.333 6.917,3.333 2,2 1.771,3.385 2.521,3.552 0.75,0.167 3.833,3.75 4.833,3.917 1,0.167 4.083,3.417 5.167,3.583 1.083,0.167 3.073,1 4.073,1.167 1,0.167 4.333,0.729 5.333,0.896 1,0.167 5.344,3.125 6.427,3.292 1.083,0.167 6.531,0.208 6.865,0.208 false 5.417,2.458 5.417,2.792 false 6.49,0.583 6.823,0.583 false 2.792,3.958 3.125,3.958 false 2.5,2.667 2.667,2.667 2.667,2.667 2.927,2.76 false 3.604,1.906 3.99,1.906 false 6.521,2.542 6.521,2.792 false 5.958,3.333 5.958,3.667 false 2.521,3.469 2.854,3.469 false 3.5,3.125 3.667,3.833 3.667,3.833 3.833,3.833 false 3.76,2.594 3.917,3.5 3.917,3.5 4.083,3.5 false 4.083,1.083 4.25,1.083 4.25,1.083 4.448,1.813 true 5.333,0.813 5.5,0.813 5.5,0.813 5.969,1.615 true 5.854,2.792 5.854,3.125 false 6.458,0.938 6.792,0.938 false 6.313,0.052 6.625,0.417 0.313,0.365 18 false 1 6.323,0.427 6.604,0.781 0.281,0.354 18 false 7 3.198,3.813 3.479,4.167 0.281,0.354 18 false 6 2.302,2.531 2.583,2.885 0.281,0.354 18 false 5 5.969,3.708 6.25,4.063 0.281,0.354 18 false 4 3.396,1.792 3.677,2.146 0.281,0.354 18 false 3 6.427,2.833 6.708,3.188 0.281,0.354 18 false 2 5.365,2.833 5.677,3.031 0.313,0.198 10 false *1 1.854,3.385 2.688,3.583 0.833,0.198 8 false 10 (102, 7) 3.885,3.75 4.885,3.948 1,0.198 8 false 8.0 (82, 71 in.*lbf) 4.167,3.427 5.156,3.615 0.99,0.188 8 false 6.0 (61, 53 in.*lbf) 5.427,3.125 6.427,3.323 1,0.198 8 false 8.0 (82, 71 in.*lbf) 3.135,1.01 4.125,1.198 0.99,0.188 8 false 6.0 (61, 53 in.*lbf) 4.375,0.74 5.365,0.927 0.99,0.188 8 false 6.0 (61, 53 in.*lbf) 6.292,0.813 6.573,1.167 0.281,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 89221 (Click here) - -
3 WIRING HARNESS CLAMP BRACKET 82715 (Click here) - -
4 POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU - (Click here) - -
5 NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY 55308B - - -
6 LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY 55480D - - -
7 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
8 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

*1 POWER DISTRIBUTION BOX ASSEMBLY - -
V100146

N*m (kgf*cm, ft.*lbf): Specified torque - -

PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:
·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.

·

When installing the main body ECU (multiplex network body ECU), always replace it with a new one.




Hide 89221 2.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Z101186

NOTICE:
·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the main body ECU (multiplex network body ECU) connector.




a.
E448347C02
0.521,0.74 0.813,0.875 true 2.667,0.74 2.958,0.875 true 3.74,0.792 4.094,0.521 true 5.969,0.76 6.344,0.531 true 2.24,2.927 2.615,2.698 true 4.083,2.938 4.323,2.938 true 4.406,2.958 4.594,3.167 true 0.354,0.656 0.667,0.854 0.313,0.198 10 false *b 0.49,1.302 0.802,1.5 0.313,0.198 10 false *a 2.49,0.656 2.802,0.854 0.313,0.198 10 false *b 4.135,0.448 4.448,0.646 0.313,0.198 10 false *c 6.375,0.448 6.688,0.646 0.313,0.198 10 false *c 2.667,2.625 2.979,2.823 0.313,0.198 10 false *d 4.573,3.188 4.885,3.385 0.313,0.198 10 false *1 3.917,2.865 4.229,3.063 0.313,0.198 10 false *2 1.354,1.948 1.677,2.281 0.323,0.333 18 false iv 5.198,1.958 5.521,2.292 0.323,0.333 18 false v 5.208,0.094 5.531,0.427 0.323,0.333 18 false iii 2.885,0.094 3.208,0.427 0.323,0.333 18 false ii 0.448,0.104 0.771,0.438 0.323,0.333 18 false i
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)
*a 20° or more *b Housing Sidewall
*c Side A *d Center of Rotation (Contacts Surface A)
V100145

Push Area
V100135

Set
V100136

Slide
V113147

Install in this Direction
V113148

Rotate in this Direction - -


i.

Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the power distribution box assembly as shown in the illustration.

HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



ii.

Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the guides.


iii.

While keeping the main body ECU (multiplex network body ECU) in contact with side A of the power distribution box assembly (axis of rotation), lower it as shown in the illustration.

NOTICE:

Do not strike or apply excessive force to the side surface of the main body ECU (multiplex network body ECU).



iv.

While pressing the main body ECU (multiplex network body ECU) against side A (center of rotation) of the power distribution box assembly, rotate it until it enters the lock of the power distribution box assembly.


v.

Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and power distribution box assembly by listening for the click sound of the lock engaging.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and power distribution box assembly are flush.




Hide 82715 3.INSTALL WIRING HARNESS CLAMP BRACKET

a.
E471029C01
3.885,1.458 4.135,1.781 0.25,0.323 18 false ii 3.708,0.49 3.865,0.802 0.156,0.313 18 true i

i.

Engage the guides to install the wiring harness clamp bracket to the power distribution box assembly with multiplex network body ECU.


ii.

Temporarily install the bolt.



Hide 4.INSTALL POWER DISTRIBUTION BOX ASSEMBLY WITH MULTIPLEX NETWORK BODY ECU

a.
E466654C01
3.104,0.333 2.875,0.281 true 3.021,1.073 2.604,1.302 true 0.448,0.052 0.938,0.385 0.49,0.333 18 true i, ii 4.49,0.042 4.833,0.417 0.344,0.375 18 false iii 1.604,2.01 2.115,2.302 0.51,0.292 18 false iv, v 3.146,0.271 3.458,0.469 0.313,0.198 10 false *a 3.063,0.979 3.25,1.167 0.188,0.188 10 true *a
*a Lock Lever - -


i.

Connect the connector.


ii.

Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.


iii.

Engage the claws.


iv.

Engage the claws.


v.

Install the power distribution box assembly with multiplex network body ECU with the bolt and 2 nuts.

Torque:
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)



b.
E466655C01
4.792,0.302 5,0.406 true 4.531,1.292 4.792,1.135 true 2.958,2.313 3.167,2.417 true 2.708,3.302 2.969,3.146 true 1,0.052 1.25,0.323 0.25,0.271 18 false i 3.74,0.073 4.021,0.385 0.281,0.313 18 false ii 1.104,2.698 1.385,3.01 0.281,0.313 18 true iv 5.885,2.802 6.115,3.115 0.229,0.313 18 true v 4.635,2.406 4.865,2.719 0.229,0.313 18 true vi 5.031,0.344 5.344,0.542 0.313,0.198 10 false *a 4.823,1.042 5.021,1.25 0.198,0.208 10 true *a 3.188,2.344 3.5,2.542 0.313,0.198 10 false *a 3.031,3.052 3.229,3.26 0.198,0.208 10 true *a 3.917,0.094 4.198,0.333 0.281,0.24 12 true *A 0.365,2.083 0.615,2.354 0.25,0.271 18 false iii
*A for HV Model - -
*a Lock Lever - -


i.

Connect the 5 connectors.


ii.

for HV Model:

1.

Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.



iii.

Connect the 2 connectors and pull down the lock levers to engage the claws and lock the 2 connectors as shown in the illustration.


iv.

Engage the clamp.


v.

Engage the clamp.


vi.

Connect the 5 connectors.



Hide 55308B 5.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
E466650C01
3.792,1.344 4.021,1.573 0.229,0.229 10 true *a 3.104,1.479 3.333,1.708 0.229,0.229 10 true *b
*a Bolt (A) *b Bolt (B)


i.

Install the No. 3 instrument panel to cowl brace sub-assembly with the 2 bolts and nut.

Torque:
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)
Bolt (A) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt (B) : 10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 55480D 6.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 8. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART