| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | ROOF CARRIER SEAL | 63437C | ( )
|
- | - |
| 2 | NO. 1 ROOF CARRIER PROTECTOR | 63444 | ( )
|
- | - |
| 3 | REAR ROOF RACK RETAINER | 63454F | - | - | - |
| ● | Non-reusable part | - | - |
Use the same procedure for the LH side and RH side.
The following procedure is for the LH side.
63437C
1.INSTALL ROOF CARRIER SEAL
Clean the roof rack assembly.
Using a heat light, heat the roof rack assembly.
| Item | Temperature |
|---|---|
| Roof Rack Assembly | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the roof rack assembly excessively.
Remove any remaining double-sided tape from the roof rack assembly.
Installing the roof carrier seal with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Wipe off any tape adhesive residue with cleaner.
Install the roof carrier seal.
Using a heat light, heat the roof rack assembly.
| Item | Temperature |
|---|---|
| Roof Rack Assembly | 20 to 30°C (68 to 86°F) |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the roof rack assembly excessively.
Remove the release paper from 3 new roof carrier seal.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the 3 roof carrier seal as shown in the illustration.
Press the roof carrier seal firmly to install it.
63444
2.INSTALL NO. 1 ROOF CARRIER PROTECTOR
| *a | Rib | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| A | 0 to 2.0 mm (0 to 0.0787 in.) | B | 0 to 7.0 mm (0 to 0.276 in.) |
Clean the roof rack assembly.
Using a heat light, heat the roof rack assembly.
| Item | Temperature |
|---|---|
| Roof Rack Assembly | 20 to 30°C (68 to 86°F) |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the roof rack assembly excessively.
Remove any remaining double-sided tape from the roof rack assembly.
Installing the No. 1 roof carrier protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
Wipe off any tape adhesive residue with cleaner.
Install the No. 1 roof carrier protector.
Using a heat light, heat the roof rack assembly.
| Item | Temperature |
|---|---|
| Roof Rack Assembly | 20 to 30°C (68 to 86°F) |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the roof rack assembly excessively.
Remove the release paper from a new No. 1 roof carrier protector.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install the No. 1 roof carrier protector as shown in the illustration.
Press the No. 1 roof carrier protector firmly to install it.
63454F
3.INSTALL REAR ROOF RACK RETAINER