Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › FRONT PILLAR UPPER COVER › from 2021.07
RM3700E _59 Vehicle Exterior _093282 EXTERIOR PANELS / TRIM _0440172 FRONT PILLAR UPPER COVER A

EXTERIOR PANELS / TRIM  FRONT PILLAR UPPER COVER  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
B614978N01
4.083,2 4.417,2 false 5.333,1.542 5.333,1.104 false 4.469,1.896 4.823,2.104 0.354,0.208 10 false ● *1 5.292,1.604 5.469,1.854 0.177,0.25 10 false ● 5.427,1.521 5.708,1.792 0.281,0.271 18 false 1 0.083,0.083 0.458,0.323 0.375,0.24 12 false *A

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT PILLAR COVER PROTECTOR 61992 (Click here) - -

*A for TMMF Made - -
*1 FRONT PILLAR COVER - -
● Non-reusable part - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 61992 1.INSTALL FRONT PILLAR COVER PROTECTOR (for TMMF Made)

Z101186

NOTICE:

When installing a new front pillar cover protector, heat the front pillar cover using a heat light.



Standard:
Item Temperature
Front Pillar Cover 20 to 30°C (68 to 86°F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts.

·

Touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the front pillar cover excessively.


a.
B614980N02
2.198,0.052 2.479,0.406 0.281,0.354 18 false i 1.552,1.604 1.833,1.958 0.281,0.354 18 false ii 5.323,1.427 5.479,1.625 0.156,0.198 10 false A

i.

Clean the front pillar cover.

1. Using a heat light, heat the front pillar cover surface.

2. Remove any remaining double-sided tape from the front pillar cover.

3. Wipe off any tape adhesive residue with cleaner.

NOTICE:
·

Installing the front pillar cover protector with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.

·

Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.




ii.

Install a new front pillar cover protector.

1. Using a heat light, heat the front pillar cover.

2. Remove the release paper from the front pillar cover protector.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.


3. Install the front pillar cover protector as shown in the illustration.

Standard Measurement:
Area Measurement Area Measurement
A -0.5 to 0.5 mm (-0.0197 to 0.0197 in.) - -


HINT:
·

Make sure that the end of the front pillar cover protector is between the location line.

·

Press the front pillar cover protector firmly to install it.