Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL SENDER GAUGE ASSEMBLY › from 2021.07
RM3700E _51 Engine / Hybrid System _093308 M15A-FKS FUEL _0440427 FUEL SENDER GAUGE ASSEMBLY A

M15A-FKS FUEL  FUEL SENDER GAUGE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A458701N03
1.802,0.552 2.135,0.552 false 5.063,2.813 5.396,2.813 false 1.604,0.417 1.885,0.771 0.281,0.354 18 false 1 5.792,2.656 6.073,3.01 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY 77020A - - -
2 FUEL SENDER GAUGE ASSEMBLY 83320 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel sender gauge assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 83320 2.REMOVE FUEL SENDER GAUGE ASSEMBLY

a.
A459926N02
0.542,0.094 0.823,0.448 0.281,0.354 18 false i 2.51,0.094 2.792,0.448 0.281,0.354 18 false ii 5.802,0.083 6.083,0.438 0.281,0.354 18 false iii

i.

Disengage the 4 clamps to disconnect the wire harness.

NOTICE:
·

Do not damage the wire harness.

·

When disengaging each wire harness from the clamp, disengage one wire at a time.




ii.

Disconnect the 2 connectors.


iii.

Disengage the 2 claws to remove the fuel sender gauge assembly from the fuel suction tube with pump and gauge assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.