Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483473 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C052646  Steering Angle Sensor Module Calibration / Parameter Memory Failure  


DESCRIPTION

When the vehicle is being driven in a straight line at 15 km/h (9 mph) for 1 second or more, the skid control ECU (brake actuator assembly) calculates the steering sensor zero point and updates the zero point if the difference between the calculated zero point and current zero point is between 10° and 15°. The ECU also stores previous zero points.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C052646 Steering Angle Sensor Module Calibration / Parameter Memory Failure After the steering sensor zero point is obtained, the zero point is lost due to power supply fluctuations, etc. and cannot be reobtained when the vehicle speed is 15 km/h (9 mph) or more.
·

Steering sensor

·

Yaw rate and acceleration sensor (airbag sensor assembly)


Brake/EPB B

CAUTION / NOTICE / HINT

NOTICE:

Because this DTC is related to a temporary loss of steering angle zero point calibration, before proceeding with the inspection, it is useful to confirm whether the power source voltage was interrupted by an operation such as removal or disconnection of the auxiliary battery.


HINT:
·

When DTC U007488 and/or U012687 is output together with DTC C052646, inspect and repair the trouble areas indicated by DTC U007488 and/or U012687 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>U007488

·

If a speed sensor, yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, the steering sensor may also appear to be malfunctioning even when normal.

·

If DTCs related to a speed sensor, yaw rate and acceleration sensor (airbag sensor assembly) are output, perform troubleshooting for those DTCs before inspecting the steering sensor.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch to ON again and check that no CAN communication system DTCs are output.

HINT:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result Proceed to
CAN communication system DTCs are output. A
CAN communication system DTCs are not output. B



A

B

2.CLEAR DTC
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.CHECK DTC
3.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and perform a road test.


b.

Drive the vehicle at a speed of 15 km/h (9 mph) and turn the steering wheel to the right and left.


Procedure1

a.

Check that no speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C052646 is output. A
Speed sensor and/or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output. B
C052646 is not output. C



Post-procedure1

a.

None



A

4.CHECK STEERING SENSOR ZERO POINT CALIBRATION

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

C

4.CHECK STEERING SENSOR ZERO POINT CALIBRATION

Pre-procedure1

a.

Drive the vehicle straight ahead at 15 km/h (9 mph) or more for at least 1 second.


Procedure1

a.

Check that the steering wheel is correctly centered while driving straight ahead.

OK:

The steering wheel is correctly centered.


HINT:

If front wheel alignment and steering are adjusted as a result of an off-center steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CLEAR DTC

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING POSITION

5.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake Booster > Clear DTCs
50002 466
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC

Pre-procedure1

a.

Turn the ignition switch to ON (READY) and perform a road test.


b.

Drive the vehicle at a speed of 15 km/h (9 mph) and turn the steering wheel to the right and left.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C052646 is not output A
C052646 is output B


HINT:

If DTC C052646 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as a loss of calibration due to the power source voltage being low.



Post-procedure1

a.

None



A

END

B