Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483473 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  C121F87  Electronic Brake Booster Control Module "A" Missing Message  C125DA2  Electronic Brake Booster Control Module "A" Backup Power Supply Voltage System Voltage Low  C125DA3  Electronic Brake Booster Control Module "A" Backup Power Supply Voltage System Voltage High  C136E00  Electronic Brake Booster Control Module "A" Backup Power Supply Voltage  C136E17  Electronic Brake Booster Control Module "A" Backup Power Supply Voltage Circuit Voltage Above Threshold  C136E1E  Electronic Brake Booster Control Module "A" Backup Power Supply Voltage Circuit Resistance Out of Range  C136E49  Electronic Brake Booster Control Module "A" Backup Power Supply Voltage Internal Electronic Failure  C137A04  Electronic Brake Booster Control Module "A" Backup Power Supply Module System Internal Failure  C137A17  Electronic Brake Booster Control Module "A" Backup Power Supply Module Circuit Voltage Above Threshold  C137A49  Electronic Brake Booster Control Module "A" Backup Power Supply Module Internal Electronic Failure  C137A86  Electronic Brake Booster Control Module "A" Backup Power Supply Module Signal (some circuit quantity, reported via serial data) Invalid  C137A87  Electronic Brake Booster Control Module "A" Backup Power Supply Module Missing Message  C13BE00  Electronic Brake Booster Control Module "A" Backup Power Supply Module Charging Circuit  C13BE49  Electronic Brake Booster Control Module "A" Backup Power Supply Module Charging Circuit Internal Electronic Failure  C13DF1C  Electronic Brake Booster Control Module "A" Backup Power Supply Module Circuit Voltage Out of Range  C13FC49  Electronic Brake Booster Control Module "A" Internal Electronic Failure  C13FD12  Electronic Brake Booster Control Module "A" Backup Power Supply Module Discharge Circuit Circuit Short to Battery  C13FD14  Electronic Brake Booster Control Module "A" Backup Power Supply Module Discharge Circuit Circuit Short to Ground or Open  C148E1C  Electronic Brake Booster Control Module "A" Backup Power Supply Module Sensor Circuit Voltage Out of Range  C14BF49  Electronic Brake Booster Control Module "A" Backup Power Supply Module Backup Circuit Internal Electronic Failure  C14CC1C  Electronic Brake Booster Control Module "A" Backup Power Supply Module Temperature Sensor Circuit Voltage Out of Range  


DESCRIPTION

The brake control power supply assembly is used as an auxiliary power supply for brake control when the voltage of the auxiliary battery is low.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C121F87 Electronic Brake Booster Control Module "A" Missing Message During IG ON, a brake control power supply assembly internal malfunction is detected. Brake control power supply assembly Brake Booster A
C125DA2 Electronic Brake Booster Control Module "A" Backup Power Supply Voltage System Voltage Low Voltage from brake control power supply assembly is less than 2.8 V for 10 seconds. Brake control power supply assembly Brake Booster A
C125DA3 Electronic Brake Booster Control Module "A" Backup Power Supply Voltage System Voltage High Brake control power supply assembly power source voltage is abnormal for 10 seconds or more. Brake control power supply assembly Brake Booster A
C136E00 Electronic Brake Booster Control Module "A" Backup Power Supply Voltage While driving at a vehicle speed of 3 km/h or more, abnormal signal is received from brake control power supply assembly for 150 seconds or more. Brake control power supply assembly Brake Booster A
C136E17 Electronic Brake Booster Control Module "A" Backup Power Supply Voltage Circuit Voltage Above Threshold During IG ON, a brake control power supply assembly cell malfunction is detected. Brake control power supply assembly Brake Booster A
C136E1E Electronic Brake Booster Control Module "A" Backup Power Supply Voltage Circuit Resistance Out of Range During IG ON, brake control power supply assembly degradation (end-of-life notification) is detected. Brake control power supply assembly Brake Booster A
C136E49 Electronic Brake Booster Control Module "A" Backup Power Supply Voltage Internal Electronic Failure During IG ON, the brake control power supply assembly self-discharge amount (current leak) is detected to be excessive (internal malfunction). Brake control power supply assembly Brake Booster A
C137A04 Electronic Brake Booster Control Module "A" Backup Power Supply Module System Internal Failure During IG ON, a brake control power supply assembly internal malfunction is detected. Brake control power supply assembly Brake Booster A
C137A17 Electronic Brake Booster Control Module "A" Backup Power Supply Module Circuit Voltage Above Threshold During IG ON, a brake control power supply assembly overvoltage malfunction is detected. Brake control power supply assembly Brake Booster A
C137A49 Electronic Brake Booster Control Module "A" Backup Power Supply Module Internal Electronic Failure During IG ON, a brake control power supply assembly power source circuit malfunction is detected. Brake control power supply assembly Brake Booster A
C137A86 Electronic Brake Booster Control Module "A" Backup Power Supply Module Signal (some circuit quantity, reported via serial data) Invalid While driving at a vehicle speed of 3 km/h or more, LIN communication from brake control power supply assembly is abnormal for 10 seconds or more. Brake control power supply assembly Brake Booster A
C137A87 Electronic Brake Booster Control Module "A" Backup Power Supply Module Missing Message LIN communication with brake control power supply assembly is abnormal for 0.5 seconds or more. Brake control power supply assembly Brake Booster A
C13BE00 Electronic Brake Booster Control Module "A" Backup Power Supply Module Charging Circuit During IG ON, a brake control power supply assembly power source backup unit internal circuit (backup output circuit) failure is detected. Brake control power supply assembly Brake Booster A
C13BE49 Electronic Brake Booster Control Module "A" Backup Power Supply Module Charging Circuit Internal Electronic Failure During IG ON, a brake control power supply assembly charging circuit malfunction is detected. Brake control power supply assembly Brake Booster A
C13DF1C Electronic Brake Booster Control Module "A" Backup Power Supply Module Circuit Voltage Out of Range During IG ON, a brake control power supply assembly power source malfunction is detected. Brake control power supply assembly Brake Booster A
C13FC49 Electronic Brake Booster Control Module "A" Internal Electronic Failure LIN communication from brake control power supply assembly is abnormal for 0.1 seconds or more. Brake control power supply assembly Brake Booster A
C13FD12 Electronic Brake Booster Control Module "A" Backup Power Supply Module Discharge Circuit Circuit Short to Battery During IG ON, a brake control power supply assembly discharging circuit malfunction is detected. Brake control power supply assembly Brake Booster A
C13FD14 Electronic Brake Booster Control Module "A" Backup Power Supply Module Discharge Circuit Circuit Short to Ground or Open During IG ON, a brake control power supply assembly discharging circuit malfunction is detected. Brake control power supply assembly Brake Booster A
C148E1C Electronic Brake Booster Control Module "A" Backup Power Supply Module Sensor Circuit Voltage Out of Range During IG ON, a brake control power supply assembly internal circuit malfunction is detected. Brake control power supply assembly Brake Booster A
C14BF49 Electronic Brake Booster Control Module "A" Backup Power Supply Module Backup Circuit Internal Electronic Failure During IG ON, a brake control power supply assembly backup circuit malfunction is detected. Brake control power supply assembly Brake Booster A
C14CC1C Electronic Brake Booster Control Module "A" Backup Power Supply Module Temperature Sensor Circuit Voltage Out of Range During IG ON, a brake control power supply assembly power source backup unit internal circuit (voltage monitor circuit) failure is detected. Brake control power supply assembly Brake Booster A

WIRING DIAGRAM

C444368E02
1.042,0.844 1.302,1.021 0.26,0.177 10 false LIN 0.854,1.344 1.313,1.521 0.458,0.177 10 false WKUP 0.979,1.833 1.302,2.01 0.323,0.177 10 false OUT 0.99,2.563 1.333,2.74 0.344,0.177 10 false +BC 0.24,4.104 1.552,4.719 1.313,0.615 10 false Brake Control Power Supply Assembly 2.708,2.729 3.573,2.927 0.865,0.198 10 false CAPACITOR 5.885,0.865 6.25,1.042 0.365,0.177 10 false CLIN 5.885,1.354 6.333,1.531 0.448,0.177 10 false CWKP 5.885,1.854 6.333,2.031 0.448,0.177 10 false CBKP 4.677,4.333 7.052,4.813 2.375,0.479 10 false Electric Brake Booster (Brake Booster with Master Cylinder Assembly) 0.844,5.354 2.469,5.552 1.625,0.198 10 false : LIN Communication Line 0.99,3.396 1.333,3.573 0.344,0.177 10 false GND 5.219,0.865 5.719,1.073 0.5,0.208 10 false A34 5.552,0.854 6.052,1.063 0.5,0.208 10 false A35 2.625,4.865 3.458,5.094 0.833,0.229 10 false *1: for LHD 5.594,1.531 6.094,1.74 0.5,0.208 10 false *2 2.656,5.313 3.688,5.573 1.031,0.26 10 false *2: for RHD 1.406,0.708 1.906,0.917 0.5,0.208 10 false 2 5.552,1.354 6.052,1.563 0.5,0.208 10 false A35 5.563,1.854 6.063,2.063 0.5,0.208 10 false A35 5.625,2.042 6.125,2.25 0.5,0.208 10 false *2 5.25,2.042 5.75,2.25 0.5,0.208 10 false *1 5.26,1.531 5.76,1.74 0.5,0.208 10 false *1 5.563,1.042 6.063,1.25 0.5,0.208 10 false *2 5.229,1.042 5.729,1.25 0.5,0.208 10 false *1 5.271,0.688 5.771,0.896 0.5,0.208 10 false 4 5.635,0.688 6.135,0.896 0.5,0.208 10 false 4 1.406,1.24 1.906,1.448 0.5,0.208 10 false 3 1.406,1.719 1.906,1.927 0.5,0.208 10 false 6 1.406,2.458 1.906,2.667 0.5,0.208 10 false 1 1.406,3.24 1.906,3.448 0.5,0.208 10 false 4 0.24,3.938 0.74,4.146 0.5,0.208 10 false O64 5.271,1.188 5.771,1.396 0.5,0.208 10 false 24 5.615,1.188 6.115,1.396 0.5,0.208 10 false 24 5.594,1.688 6.094,1.896 0.5,0.208 10 false 17 5.25,1.677 5.75,1.885 0.5,0.208 10 false 17 5.219,1.354 5.719,1.563 0.5,0.208 10 false A34 5.219,1.854 5.719,2.063 0.5,0.208 10 false A34

CAUTION / NOTICE / HINT

NOTICE:

After replacing the electric brake booster (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY


PROCEDURE

1.INSPECT BRAKE CONTROL POWER SUPPLY (+BC TERMINAL)

Pre-procedure1

a.

Disconnect the 064 brake control power supply assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O64)Location & Routing

Click Connector(O64)Body>Floor Wire>Brake Control Power Supply Assembly

O64-1 (+BC) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.INSPECT BRAKE CONTROL POWER SUPPLY (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BRAKE CONTROL POWER SUPPLY (GND TERMINAL)

Pre-procedure1

a.

Disconnect the 064 brake control power supply assembly connector.


Procedure1

a.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O64)Location & Routing

Click Connector(O64)Body>Floor Wire>Brake Control Power Supply Assembly

O64-4 (GND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CONFIRM MODEL
a.

Choose the model to be inspected


Result:
Result Proceed to
for LHD A
for RHD B



A

4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE CONTROL POWER SUPPLY ASSEMBLY)

B

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE CONTROL POWER SUPPLY ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE CONTROL POWER SUPPLY ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A34 electric brake booster (brake booster with master cylinder assembly) connector.


b.

Disconnect the O64 brake control power supply assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A34,O64)Location & Routing

Click Connector(A34)Engine Compartment>Engine Room Main Wire>Brake Booster Control ECU (Brake Booster with Master Cylinder Assembly)

Click Connector(O64)Body>Floor Wire>Brake Control Power Supply Assembly

A34-4 (CLIN) - O64-2 (LIN) Always Below 1 Ω
A34-4 (CLIN) or O64-2 (LIN) - Body ground Always 10 kΩ or higher
A34-17 (CBKP) - O64-6 (OUT) Always Below 1 Ω
A34-17 (CBKP) or O64-6 (OUT) - Body ground Always 10 kΩ or higher
A34-24 (CWKP) - O64-3 (WKUP) Always Below 1 Ω
A34-24 (CWKP) or O64-3 (WKUP) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE CONTROL POWER SUPPLY ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A35 electric brake booster (brake booster with master cylinder assembly) connector.


b.

Disconnect the O64 brake control power supply assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A35,O64)Location & Routing

Click Connector(A35)Engine Compartment>Engine Room Main Wire>Brake Booster Control ECU (Brake Booster with Master Cylinder Assembly)

Click Connector(O64)Body>Floor Wire>Brake Control Power Supply Assembly

A35-4 (CLIN) - O64-2 (LIN) Always Below 1 Ω
A35-4 (CLIN) or O64-2 (LIN) - Body ground Always 10 kΩ or higher
A35-17 (CBKP) - O64-6 (OUT) Always Below 1 Ω
A35-17 (CBKP) or O64-6 (OUT) - Body ground Always 10 kΩ or higher
A35-24 (CWKP) - O64-3 (WKUP) Always Below 1 Ω
A35-24 (CWKP) or O64-3 (WKUP) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR