Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE CONTROL POWER SUPPLY › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0483477 BRAKE CONTROL POWER SUPPLY A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE CONTROL POWER SUPPLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C461352N01
3.563,2.031 4.052,2.031 false 3.656,0.708 4.042,0.708 false 6.458,0.24 6.844,0.24 false 6.469,0.667 6.813,0.667 false 6.302,0.094 6.583,0.448 0.281,0.354 18 false 1 6.302,0.51 6.583,0.865 0.281,0.354 18 false 2 4.344,0.531 4.625,0.885 0.281,0.354 18 false 3 4.333,1.885 4.615,2.24 0.281,0.354 18 false 4 2.646,1.021 2.938,1.26 0.292,0.24 10 false x2 3.635,2.521 3.927,2.76 0.292,0.24 10 false x4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 BRAKE CONTROL POWER SUPPLY ASSEMBLY 89680 (Click here) - -
4 NO. 1 BRAKE CONTROL POWER SUPPLY BRACKET 89686 (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake control power supply assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 89680 3.REMOVE BRAKE CONTROL POWER SUPPLY ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake control power supply assembly by the connector.

·

Do not drop the brake control power supply assembly when carrying it.




a.
C461350C01
6.698,0.552 6.813,0.313 true 0.302,0.042 0.583,0.396 0.281,0.354 18 false i 3.74,0.031 4.531,0.344 0.792,0.313 18 true ii, iii, iv 6.833,0.219 7.094,0.448 0.26,0.229 10 false *a
*a Lock Lever - -


i.

Turn back the floor carpet.


ii.

Remove the 2 bolts and disengage the hook to remove the brake control power supply assembly.


iii.

Disconnect the brake control power supply assembly connector.


iv.

Disengage the claw and raise the lock lever to disconnect the brake control power supply assembly connector as shown in the illustration.

NOTICE:

After disconnecting the brake control power supply assembly connector, make sure that dirt, water or other foreign matter does not contact the connecting parts of the brake control power supply assembly connector.




Hide 89686 4.REMOVE NO. 1 BRAKE CONTROL POWER SUPPLY BRACKET

Z101186

NOTICE:
·

Do not hold the brake control power supply assembly by the connector.

·

Do not drop the brake control power supply assembly when carrying it.




a.
C461351