Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093836 TELEMATICS _0483689 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B153711  Telephone Sub Antenna Circuit Short to Ground  B153713  Telephone Sub Antenna Circuit Open  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B153711 Telephone Sub Antenna Circuit Short to Ground Navigation antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly


Telematics A
B153713 Telephone Sub Antenna Circuit Open Navigation antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit)
·

Telephone transceiver assembly

·

Navigation antenna assembly

·

Antenna cord sub-assembly


Telematics A

WIRING DIAGRAM

E427067E38
5.021,1.865 6.438,2.292 1.417,0.427 10 false Telephone Transceiver Assembly 3.573,1.885 4.49,2.333 0.917,0.448 10 false Antenna Cord Sub-assembly 2.135,1.677 3.375,2.104 1.24,0.427 10 false Navigation Antenna Assembly 4.75,0.719 5.573,1.094 0.823,0.375 10 false C 4.74,1.26 5.563,1.635 0.823,0.375 10 false C 4.719,1.031 5.542,1.406 0.823,0.375 10 false 1a 4.75,0.51 5.573,0.885 0.823,0.375 10 false 1 3.271,0.719 4.094,1.094 0.823,0.375 10 false A 3.281,1.25 4.104,1.625 0.823,0.375 10 false A 3.26,1.042 4.083,1.417 0.823,0.375 10 false 4a 3.271,0.51 4.094,0.885 0.823,0.375 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System (for eCall).

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telephone transceiver assembly, make sure to replace it with a new one.

·

Before replacing the telematics transceiver assembly, refer to Service Bulletin.



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

Result:
Proceed to
NEXT



NEXT

2.CHECK DTC
2.CHECK DTC

Pre-procedure1

a.

Turn the ignition switch to ON and wait for 10 seconds or more.


Procedure1

a.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
Result:
Result Proceed to
DTCs are not output A
B157111 or B157113 is output B
None of the above conditions are met C



Post-procedure1

a.

None



A

B

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

C

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

4.INSPECT ANTENNA CORD SUB-ASSEMBLY

Pre-procedure1

a.

Disconnect the antenna cord sub-assembly from the navigation antenna assembly.


b.

Disconnect the antenna cord sub-assembly from the antenna cord sub-assembly.


Procedure1

a.
E427068C38
1.427,1.719 1.917,2.021 0.49,0.302 1.427,0.115 1.917,0.417 0.49,0.302 2.104,0.802 2.677,0.604 true 1.802,2.74 2.375,2.542 true 0.271,0.188 0.583,0.385 0.313,0.198 10 false *a 0.354,1.917 0.667,2.115 0.313,0.198 10 false *b 1.625,1.802 2.333,2.104 0.708,0.302 10 false C 1.635,0.208 2.344,0.51 0.708,0.302 10 false A 2.771,0.51 3.115,0.802 0.344,0.292 10 false 4a 2.438,2.427 2.781,2.719 0.344,0.292 10 false 1a
*a Front view of wire harness connector
(to Navigation Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-4 - C-1 Always Below 1 Ω
A-4a - C-1a Always Below 1 Ω
A-4 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

5.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Replace the telephone transceiver assembly with a new one.

HINT:

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL



Result:
Proceed to
NEXT



NEXT