If the telephone transceiver assembly detects an error in communication between the telephone transceiver assembly and the airbag sensor assembly as a result of the telephone transceiver assembly self check, this DTC will be set.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| B15C464 | Airbag Signal Signal Plausibility Failure | Telephone transceiver assembly detects an error in signals from airbag sensor assembly when ignition switch is ON. | ·
Airbag system ·
Harness or connector ·
Airbag sensor assembly ·
Telephone transceiver assembly |
Telematics | A |
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Before replacing the telematics transceiver assembly, refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
Post-procedure1
None
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Turn the ignition switch to ON and wait for 10 seconds or more.
Procedure1
Check for DTCs and check that no DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| B15C464 is output | B |
| None of the above conditions are met | C |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>DIAGNOSTIC TROUBLE CODE CHART
Pre-procedure1
Remove the telephone transceiver assembly but do not disconnect the connectors.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
Procedure1
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Check the input waveform.
Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telephone transceiver assembly while the airbag sensor assembly connectors are connected.)
| Item | Condition |
|---|---|
| Tester connection | H85-13 (GSW) - Body ground |
| Tool setting | 5.0 V/DIV., 20 ms/DIV. |
| Vehicle condition | Ignition switch ON |
The waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the telephone transceiver assembly with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (except TAS Type)>REMOVAL
The ignition switch must be off.
Do not exchange the telephone transceiver assembly with one from another vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
Disconnect the H85 telephone transceiver assembly connector.
Procedure1
Disconnect the H14 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H85,H14)Location & Routingewd_type=routing;type=c,c;code=H85,H14 Click Connector(H85)Instrument Panel>Instrument Panel Wire / Speaker Wire>Telematics Transceiverewd_type=component;type=c;code=H85;pinno=13 Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assemblyewd_type=component;type=c;code=H14;pinno=23 |
||
| H85-13 (GSW) - H14-23 (GSW3) | Always | Below 1 Ω |
| H85-13 (GSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG