While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly*3 or clutch start switch assembly*4 and to terminal STA of the ECM (STA signal).
*1: w/o Entry and Start System
*2: w/ Entry and Start System
*3: for Continuously Variable Transaxle Models
*4: for Manual Transaxle Models
Refer to DTC P061512.
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>P061512
Inspect the fuses for circuits related to this system before performing the following procedure.
Confirm the vehicle specifications.
| Result | Proceed to |
|---|---|
| w/ Stop and Start System | A |
| w/o Stop and Start System | B |
A
B
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).
Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.
| Tester Display |
|---|
| Starter SW |
| Condition | GTS Display (Starter SW) |
|---|---|
| Ignition switch ON | OFF |
| Engine started | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/o Stop And Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D54)Location & Routingewd_type=routing;type=c;code=D54 Click Connector(D54)Engine Compartment>Engine Wire>Starter Assemblyewd_type=component;type=c;code=D54;pinno=1 |
||
| 3 (ST NO. 1 relay) - D54-1 (ST) | Always | Below 1 Ω |
| 3 (ST NO. 1 relay) or D54-1 (ST) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D80)Location & Routingewd_type=routing;type=c;code=D80 Click Connector(D80)Engine Compartment>Engine Wire>Starter Assemblyewd_type=component;type=c;code=D80;pinno=1 |
||
| Positive (+) battery terminal - D80-1 (B) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (ST NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ST NO. 1 relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A64)Location & Routingewd_type=routing;type=c;code=A64 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=1 |
||
| 2 (ST NO. 1 relay) - A64-1 (L) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the stop and start system.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch assembly.
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the engine stop and start ECU connector.
Disconnect the ECM connector.
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the clutch start switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A64,A54,A67,H45)Location & Routingewd_type=routing;type=c,c,c,c;code=A64,A54,A67,H45 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=1 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=30 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=21 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=3 |
||
| A64-1 (L) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A54-30 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A67-21 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| H45-3 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| H45-3 (STA), 2 (ST NO. 1 relay), A64-1 (L) or A54-30 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the clutch start switch assembly connector.
Disconnect the ECM connector.
Disconnect the engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H45,A64,A67,A54)Location & Routingewd_type=routing;type=c,c,c,c;code=H45,A64,A67,A54 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=10 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=2 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=17 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=23 |
||
| H45-10 (STAR) - A64-2 (B) | Always | Below 1 Ω |
| H45-10 (STAR) - A67-17 (CLL) | Always | Below 1 Ω |
| A67-17 (CLL) - A54-23 (NSW) | Always | Below 1 Ω |
| H45-10 (STAR), A67-17 (CLL), A54-23 (NSW) or A64-2 (B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Disconnect the ECM connector.
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A64,A54,A67)Location & Routingewd_type=routing;type=c,c,c;code=A64,A54,A67 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=1 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=30 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=21 |
||
| A64-1 (L) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A54-30 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A67-21 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A64-1 (L), 2 (ST NO. 1 relay), A67-21 (STA) or A54-30 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the clutch start switch assembly connector.
Disconnect the engine stop and start ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H54,A64,A67)Location & Routingewd_type=routing;type=c,c,c;code=H54,A64,A67 Click Connector(H54)Instrument Panel>Instrument Panel Wire / Speaker Wire>Ignition Or Starter Switch Assemblyewd_type=component;type=c;code=H54;pinno=4 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=2 Click Connector(A67)Instrument Panel>Engine Room Main Wire>Engine Stop and Start ECUewd_type=component;type=c;code=A67;pinno=17 |
||
| H54-4 (ST2) - A64-2 (B) | Always | Below 1 Ω |
| H54-4 (ST2) - A67-17 (CLL) | Always | Below 1 Ω |
| H54-4 (ST2) or A64-2 (B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).
Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.
| Tester Display |
|---|
| Starter SW |
| Condition | GTS Display (Starter SW) |
|---|---|
| Ignition switch ON | OFF |
| Engine started | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).
Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.
| Tester Display |
|---|
| Starter SW |
| Condition | GTS Display (Starter SW) |
|---|---|
| Ignition switch ON | OFF |
| Engine started | ON |
| Result | Proceed to |
|---|---|
| NG (for Continuously Variable Transaxle Models) | A |
| NG (for Manual Transaxle Models) | B |
| OK | C |
A
B
C
Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the park/neutral position switch assembly connector.
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D45,A54,H45)Location & Routingewd_type=routing;type=c,c,c;code=D45,A54,H45 Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assemblyewd_type=component;type=c;code=D45;pinno=5 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=30 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=3 |
||
| D45-5 (L) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A54-30 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| H45-3 (STA), 2 (ST NO. 1 relay), D45-5 (L) or A54-30 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H45,D45,A54)Location & Routingewd_type=routing;type=c,c,c;code=H45,D45,A54 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=10 Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assemblyewd_type=component;type=c;code=D45;pinno=4 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=23 |
||
| H45-10 (STAR) - D45-4 (B) | Always | Below 1 Ω |
| H45-10 (STAR) - A54-23 (NSW) | Always | Below 1 Ω |
| H45-10 (STAR), D45-4 (B) or A54-23 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D45,A54)Location & Routingewd_type=routing;type=c,c;code=D45,A54 Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assemblyewd_type=component;type=c;code=D45;pinno=5 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=30 |
||
| D45-5 (L) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A54-30 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| D45-5 (L), 2 (ST NO. 1 relay) or A54-30 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H54,D45,A54)Location & Routingewd_type=routing;type=c,c,c;code=H54,D45,A54 Click Connector(H54)Instrument Panel>Instrument Panel Wire / Speaker Wire>Ignition Or Starter Switch Assemblyewd_type=component;type=c;code=H54;pinno=4 Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assemblyewd_type=component;type=c;code=D45;pinno=4 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=23 |
||
| H54-4 (ST2) - D45-4 (B) | Always | Below 1 Ω |
| H54-4 (ST2) - A54-23 (NSW) | Always | Below 1 Ω |
| H54-4 (ST2), D45-4 (B) or A54-23 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch start switch assembly.
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the clutch start switch assembly connector.
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A64,A54,H45)Location & Routingewd_type=routing;type=c,c,c;code=A64,A54,H45 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=1 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=30 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=3 |
||
| A64-1 (L) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A54-30 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| H45-3 (STA), 2 (ST NO. 1 relay), A64-1 (L) or A54-30 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H45,A64)Location & Routingewd_type=routing;type=c,c;code=H45,A64 Click Connector(H45)Instrument Panel>Instrument Panel Wire / Speaker Wire>Certification ECUewd_type=component;type=c;code=H45;pinno=10 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=2 |
||
| H45-10 (STAR) - A64-2 (B) | Always | Below 1 Ω |
| H45-10 (STAR) or A64-2 (B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the clutch start switch assembly connector.
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A64,A54)Location & Routingewd_type=routing;type=c,c;code=A64,A54 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=1 Click Connector(A54)Engine Compartment>Engine Room Main Wire>ECMewd_type=component;type=c;code=A54;pinno=30 |
||
| A64-1 (L) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A54-30 (STA) - 2 (ST NO. 1 relay) | Always | Below 1 Ω |
| A64-1 (L), 2 (ST NO. 1 relay) or A54-30 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H54,A64)Location & Routingewd_type=routing;type=c,c;code=H54,A64 Click Connector(H54)Instrument Panel>Instrument Panel Wire / Speaker Wire>Ignition Or Starter Switch Assemblyewd_type=component;type=c;code=H54;pinno=4 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=2 |
||
| H54-4 (ST2) - A64-2 (B) | Always | Below 1 Ω |
| H54-4 (ST2) or A64-2 (B) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/o Stop And Start System)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D54)Location & Routingewd_type=routing;type=c;code=D54 Click Connector(D54)Engine Compartment>Engine Wire>Starter Assemblyewd_type=component;type=c;code=D54;pinno=1 |
||
| 3 (ST NO. 1 relay) - D54-1 (ST) | Always | Below 1 Ω |
| 3 (ST NO. 1 relay) or D54-1 (ST) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D80)Location & Routingewd_type=routing;type=c;code=D80 Click Connector(D80)Engine Compartment>Engine Wire>Starter Assemblyewd_type=component;type=c;code=D80;pinno=1 |
||
| Positive (+) battery terminal - D80-1 (B) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | No. 1 Engine Room Relay Block and Junction Block Assembly |
| *2 | ST NO. 1 Relay |
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (ST NO. 1 relay) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from No. 1 engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ST NO. 1 relay) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for Continuously Variable Transaxle Models) | A |
| OK (for Manual Transaxle Models) | B |
| NG | C |
A
B
C
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(D45)Location & Routingewd_type=routing;type=c;code=D45 Click Connector(D45)Engine Compartment>Engine Wire>Park/Neutral Position Switch Assemblyewd_type=component;type=c;code=D45;pinno=5 |
||
| 2 (ST NO. 1 relay) - D45-5 (L) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST NO. 1 relay from the No. 1 engine room relay block and junction block assembly.
Disconnect the clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(A64)Location & Routingewd_type=routing;type=c;code=A64 Click Connector(A64)Instrument Panel>Engine Room Main Wire>Clutch Start Switch Assemblyewd_type=component;type=c;code=A64;pinno=1 |
||
| 2 (ST NO. 1 relay) - A64-1 (L) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Fully depress the clutch pedal (for Manual Transaxle Models with Clutch Start System).
Check the value displayed on the GTS when the ignition switch is turned to ON and START positions.
| Tester Display |
|---|
| Starter SW |
| Condition | GTS Display (Starter SW) |
|---|---|
| Ignition switch ON | OFF |
| Engine started | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG