Home › Drivetrain › K320 (MULTIDRIVE / CVT) › PARK / NEUTRAL POSITION SWITCH
RM3700E _52 Drivetrain _092906 K320 MULTIDRIVE / CVT _0438036 PARK / NEUTRAL POSITION SWITCH A

K320 MULTIDRIVE / CVT  PARK / NEUTRAL POSITION SWITCH  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C446031N07
1.938,1.083 2.271,1.083 false 1.958,1.771 2.292,1.771 false 2.031,2.583 2.365,2.583 false 6.448,0.25 6.781,0.25 false 6.417,0.698 6.75,0.698 false 4.563,1.073 4.896,1.073 false 5.677,2.208 6.01,2.208 false 5.948,0.094 6.531,0.365 0.583,0.271 18 false 1, 2 6.24,0.542 6.521,0.896 0.281,0.354 18 false 3 2.333,0.948 2.615,1.302 0.281,0.354 18 false 4 2.385,1.615 2.667,1.969 0.281,0.354 18 false 5 2.438,2.427 2.719,2.781 0.281,0.354 18 false 6 4.396,0.917 4.677,1.271 0.281,0.354 18 false 7 6.052,2.063 6.333,2.417 0.281,0.354 18 false 8 5.385,1.583 5.635,1.75 0.25,0.167 10 false x3

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 SECURE VEHICLE - (Click here) - -
3 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 AIR CLEANER CAP WITH AIR CLEANER HOSE - - - -
5 AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 17801 - - -
6 AIR CLEANER CASE SUB-ASSEMBLY 17701 - - -
7 ECM 89661 - - -
8 BATTERY CLAMP SUB-ASSEMBLY 74404A - - -

C429226N03
2.917,2.417 3.25,2.417 false 2.771,1.417 3.354,1.417 false 3.969,0.667 4.302,0.667 false 2.688,2.052 3.021,2.052 false 2.604,1.281 2.917,1.667 0.313,0.385 18 false 9 2.625,2.313 3,2.667 0.375,0.354 18 false 11 4.344,0.594 4.5,0.75 0.156,0.156 10 false ● 4.292,2.26 4.604,2.417 0.313,0.156 10 false x2 2.375,1.917 2.75,2.271 0.375,0.354 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

9 TRANSMISSION CONTROL CABLE ASSEMBLY 33820B (Click here) - -
10 TRANSMISSION CONTROL SHAFT LEVER 33572C (Click here) - -
11 PARK/NEUTRAL POSITION SWITCH ASSEMBLY 84540 (Click here) - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the park/neutral position switch assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Air intake system parts Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click here(Click here)



Hide 2.SECURE VEHICLE

a.
C432457N01
0.417,0.083 0.698,0.438 0.281,0.354 18 false i

i.

Fully apply the parking brake and chock a wheel.

CAUTION:
·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.





Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17801 5.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 6.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 8.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 33820B 9.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C431092C01
2.073,2.063 2.385,1.802 false 2.417,1.719 2.729,1.875 0.313,0.156 10 false *1 3.104,2.719 3.417,2.875 0.313,0.156 10 false *a 0.656,0.135 0.833,0.385 0.177,0.25 18 true i 3.917,1.167 4.094,1.417 0.177,0.25 18 true ii
*1 Clip - -
*a 45° to 60° - -


i.

While disengaging the clip as shown in the illustration, disconnect the transmission control cable assembly from the transmission control shaft lever together with the clip.


ii.

Remove the clip to separate the transmission control cable assembly from the No. 1 transmission control cable bracket.



Hide 35572C 10.REMOVE TRANSMISSION CONTROL SHAFT LEVER

a.
C432075N01
0.583,0.104 0.781,0.417 0.198,0.313 18 true i 3.958,0.083 4.156,0.396 0.198,0.313 18 true ii

i.

Disconnect the park/neutral position switch assembly connector.


ii.

Using a piece of wood or equivalent to secure the transmission control shaft lever to prevent it from rotating, remove the nut, washer and transmission control shaft lever from the manual valve lever shaft.

NOTICE:
C432070C02
1.458,0.417 1.667,0.167 1.667,0.167 1.833,0.167 true 1.833,1.323 2.333,0.583 2.333,0.583 2.5,0.583 true 1.479,1.833 1.896,1.833 true 1.885,0.104 2.167,0.344 0.281,0.24 10 false *1 2.542,0.521 2.823,0.76 0.281,0.24 10 false *2 1.271,1.771 1.469,1.917 0.198,0.146 10 true *3
*1 Transmission Control Shaft Lever
*2 Manual Valve Link Lever Sub-assembly
*3 Manual Valve


If the transmission control shaft lever is not secured when loosening the nut, the manual valve link lever sub-assembly may separate from the manual valve.




Hide 84540 11.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C430100N01
2.396,0.083 2.563,0.417 0.167,0.333 18 true i

i.

Remove the 2 bolts and park/neutral position switch assembly from the continuously variable transaxle assembly.

NOTICE:

Before removing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to remove the park/neutral position switch assembly straight along the manual valve lever shaft sub-assembly while being careful not to deform the plate spring that supports the manual valve lever shaft sub-assembly. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.