Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093686 AUDIO / VIDEO _0484174 AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type with TAS Type)  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume based on vehicle speed signals sent from the combination meter assembly.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective system based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E463249E01
1.667,0.156 3.031,0.427 1.365,0.271 10 false to Other Systems 2.323,1.385 2.635,1.583 0.313,0.198 10 false +S 2.625,1.271 2.938,1.469 0.313,0.198 10 false 36 4.375,1.271 4.688,1.469 0.313,0.198 10 false 27 4.635,1.385 5.083,1.604 0.448,0.219 10 false SPD 4.229,1.927 5.063,2.135 0.833,0.208 10 false H79 4.229,2.094 6.844,2.448 2.615,0.354 10 false Radio and Display Receiver Assembly 1.281,1.917 2.052,2.115 0.771,0.198 10 false H6 1.281,2.083 3.25,2.438 1.969,0.354 10 false Combination Meter Assembly

PROCEDURE

1.CHECK STATUS INDICATORS

Result:
Result Proceed to
CAN communication is red A
CAN communication indicator is green B



A

B

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E396774C33
1.448,0.188 1.948,0.5 0.5,0.313 0.698,2.052 1.083,1.521 true 0.573,2.063 0.885,2.26 0.313,0.198 10 false +S 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 1.615,0.271 1.927,0.469 0.313,0.198 10 false H6 2.802,3.604 3.26,3.802 0.458,0.198 10 false GND
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal H6-36 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H6-36 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.
E360497C45
1.5,0.333 1.917,0.583 0.417,0.25 0.781,2.104 1.135,1.594 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 1.583,0.365 1.896,0.563 0.313,0.198 10 false H79 0.646,2.115 1.083,2.344 0.438,0.229 10 false SPD 2.875,3.667 3.313,3.896 0.438,0.229 10 false GND 1.208,3.917 1.646,4.146 0.438,0.229 10 false A
*a Component with harness connected
(Radio and Display Receiver Assembly)


Check the input waveform.

i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal H79-27 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H79-27 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR