Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443936 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B638011N01
2.542,1.646 4.188,3.208 1.646,1.563 5.927,1.927 6.594,2.094 0.667,0.167 5.885,1.885 6.635,2.135 0.75,0.25 6.521,0.177 6.854,0.177 false 1.563,0.698 1.896,0.698 false 3.979,2.208 3.979,2.542 false 5.177,2.51 5.177,2.76 false 2.969,2.542 2.969,2.875 false 1.156,4.938 1.156,5.271 false 3.375,3.219 3.375,3.51 false 6.479,0.573 6.813,0.573 false 6.094,1.531 6.24,1.76 6.24,1.76 6.24,1.927 false 6.458,0.948 6.625,0.948 6.625,0.948 6.677,1.125 false 5.219,2.771 5.5,3.125 0.281,0.354 18 false 8 5.354,0.021 6.583,0.385 1.229,0.365 18 false 1, 3, 7, 11 1.094,5.271 1.375,5.625 0.281,0.354 18 false 6 1.927,0.542 2.208,0.896 0.281,0.354 18 false 5 3.01,2.844 3.292,3.198 0.281,0.354 18 false 2 3.906,2.531 4.219,2.729 0.313,0.198 10 false *1 3.406,3.458 3.688,3.813 0.281,0.354 18 false 4 2.073,4.073 2.448,4.313 0.375,0.24 10 false x3 6.271,0.792 6.552,1.146 0.281,0.354 18 false 9 5.729,0.396 6.521,0.74 0.792,0.344 18 false 10, 12 6.031,1.927 6.594,2.052 0.563,0.125 8 false 62 (632)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT SPIRAL CABLE SUB-ASSEMBLY 84306 (Click here) - -
2 STEERING SENSOR 89245B (Click here) - -
3 PLACE FRONT WHEELS FACING STRAIGHT AHEAD - (Click here) - -
4 INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY 84306 (Click here) - -
5 UPPER STEERING COLUMN COVER 45286B - - -
6 LOWER STEERING COLUMN COVER 45287 - - -
7 ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY 84306 (Click here) - -
8 STEERING WHEEL ASSEMBLY 45100 (Click here) - -
9 HORN BUTTON ASSEMBLY 45130 - - -
10 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
11 INSPECT SRS WARNING LIGHT - (Click here) - -
12 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

*1 SPIRAL CABLE SUB-ASSEMBLY - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.
B597004C01
4.052,1 4.906,0.698 true 4.906,1.354 4.021,1.073 true 2.958,1.073 2.385,0.813 2.385,0.813 3.052,1.031 true 0.365,0.063 0.646,0.417 0.281,0.354 18 false i 4.948,0.594 5.26,0.792 0.313,0.198 10 false *a 4.969,1.281 5.281,1.479 0.313,0.198 10 false *c 2.188,0.74 2.5,0.938 0.313,0.198 10 false *b
*a Check Window *b Matchmark
*c Top of Flat Cable U-turn - -


i.

Check if the spiral cable sub-assembly is centered.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.




b.
B597005C01
1.656,1.083 2.021,0.719 true 5.156,2.177 5.813,1.406 true 4.833,2.708 4.156,3.063 true 4.854,3.458 4.115,3.135 true 3.125,3.104 2.51,2.938 2.51,2.938 3.021,3.146 true 0.375,0.042 0.656,0.396 0.281,0.354 18 false i 2.031,0.573 2.344,0.771 0.313,0.198 10 false *a 4.833,2.583 5.146,2.781 0.313,0.198 10 false *b 4.865,3.396 5.177,3.594 0.313,0.198 10 false *d 2.354,2.823 2.563,3.021 0.208,0.198 10 true *c 5.073,2.188 5.385,2.385 0.313,0.198 10 false *a 0.188,0.417 0.469,0.771 0.281,0.354 18 false 1 2.51,0.417 2.792,0.771 0.281,0.354 18 false 2 4.844,0.417 5.125,0.771 0.281,0.354 18 false 3 2.51,2.167 2.792,2.521 0.281,0.354 18 false 4
*a Interlock *b Check Window
*c Matchmark *d Top of Flat Cable U-turn
V113147

Rotation Direction - -


i.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Make sure to observe the following precautions, otherwise the spiral cable sub-assembly may be damaged.

·

Release the interlock before rotating the spiral cable sub-assembly.

·

Do not rotate the spiral cable sub-assembly using the airbag wire harness.

·

Do not rotate the spiral cable sub-assembly with excessive force.



1.

While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable with sensor sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.


2.

If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

3.

While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


4.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable with sensor sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.





Hide 89245B 2.INSTALL STEERING SENSOR

Z101186

NOTICE:

Remove the steering sensor from the spiral cable sub-assembly only when replacing the spiral cable sub-assembly.



a.

Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.

B585635C01
4.958,0.417 5.208,0.865 true 3.833,0.51 4.115,0.865 0.281,0.354 18 false i 4.688,0.719 5.24,1.073 0.552,0.354 18 false iii 4.844,0.26 5.156,0.458 0.313,0.198 10 false *a 3.167,0.635 3.385,0.813 0.219,0.177 10 true *b 0.417,0.104 0.969,0.458 0.552,0.354 18 false ii 0.99,0.604 1.208,0.781 0.219,0.177 10 true *b
*a Lock Pin *b Guide


i.

Align the guides to install the steering sensor to the spiral cable sub-assembly.


ii.

Engage the claws to install the steering sensor to the spiral cable sub-assembly.

NOTICE:
·

Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

·

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.

·

The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.




iii.

Remove the lock pin from the steering sensor.



Hide 3.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

a.
B620947


Hide 84306 4.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Z101186

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).

·

When rotating the spiral cable with sensor sub-assembly to check the operation of the spiral cable with sensor sub-assembly (checking for abnormal noise, checking the DTC, Data list, etc.) make sure to perform the inspection with the steering wheel assembly installed.




a.
B620238C07
0.396,0.781 1.333,0.781 true 0.333,0.094 0.615,0.448 0.281,0.354 18 false i 4.604,0.094 4.885,0.448 0.281,0.354 18 false ii 0.198,0.677 0.479,1.031 0.281,0.354 10 false *a 1.865,1.792 2.115,2.021 0.25,0.229 12 true *B 3.052,1.781 3.302,2.01 0.25,0.229 12 false *A
*A w/ Entry and Start System *B w/o Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B620247N01
0.073,0.042 0.354,0.396 0.281,0.354 18 false i 4.177,0.01 4.458,0.365 0.281,0.354 18 false ii

i.

Check that the front wheels are aligned facing straight ahead.


ii.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the turn signal switch cancel ratchet may snap.




c.
B620245N02
4.625,1.188 4.802,1.469 0.177,0.281 18 true i 5.99,1.198 6.177,1.49 0.188,0.292 18 true i 5.24,0.708 5.406,0.979 0.167,0.271 18 true i 0.656,1.563 0.917,1.875 0.26,0.313 18 true iii 1.76,0.99 2.021,1.271 0.26,0.281 18 true iii 2.365,1.281 2.615,1.563 0.25,0.281 18 true iii 2.229,2.021 2.448,2.302 0.219,0.281 18 true ii 0.563,1.177 0.792,1.5 0.229,0.323 18 true iv

i.

Engage the claw and clip to install the spiral cable with sensor sub-assembly.


ii.

Install the wire harness to the spiral cable with sensor sub-assembly.


iii.

Connect each connector.


iv.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




Hide 45286B 5.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 6.INSTALL LOWER STEERING COLUMN COVER

Hide 84306 7.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Z101186

NOTICE:

Do not rotate the spiral cable with sensor sub-assembly with the battery connected and the ignition switch on (IG).



a.
B620238C07
0.396,0.781 1.333,0.781 true 0.333,0.094 0.615,0.448 0.281,0.354 18 false i 4.604,0.094 4.885,0.448 0.281,0.354 18 false ii 0.198,0.677 0.479,1.031 0.281,0.354 10 false *a 1.865,1.792 2.115,2.021 0.25,0.229 12 true *B 3.052,1.781 3.302,2.01 0.25,0.229 12 false *A
*A w/ Entry and Start System *B w/o Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B597006C02
3.917,1.104 4.906,0.656 true 4.906,1.521 3.896,1.156 true 0.365,0.063 0.646,0.417 0.281,0.354 18 false i 4.927,0.552 5.24,0.75 0.313,0.198 10 false *a 4.948,1.427 5.26,1.625 0.313,0.198 10 false *b
*a Check Window *b Top of Flat Cable U-turn


i.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The top of the flat cable U-turn can be checked from the check window.




c.
B597007C01
1.948,0.427 1.521,1.031 true 5.333,1.938 5.823,1.219 true 5.052,2.594 3.99,2.979 true 5.021,3.365 3.948,3.031 true 0.406,0.083 0.688,0.438 0.281,0.354 18 false i 0.083,0.333 0.365,0.688 0.281,0.354 18 false 1 2.417,0.313 2.698,0.667 0.281,0.354 18 false 2 2.417,2.083 2.698,2.438 0.281,0.354 18 false 4 4.75,0.333 5.031,0.688 0.281,0.354 18 false 3 1.969,0.25 2.281,0.448 0.313,0.198 10 false *a 5.063,2.49 5.375,2.688 0.313,0.198 10 false *b 5.042,3.302 5.354,3.5 0.313,0.198 10 false *c 5.24,1.938 5.552,2.135 0.313,0.198 10 false *a
*a Interlock *b Check Window
*c Top of Flat Cable U-turn - -
V113147

Rotation Direction - -


i.

If the spiral cable with sensor sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.

·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



1.

While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


2.

If the spiral cable with sensor sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.

3.

While pushing on the interlock, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable with sensor sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.


4.

Check that the spiral cable with sensor sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.





Hide 45100 8.INSTALL STEERING WHEEL ASSEMBLY

Z101186

Click here(Click here)

Hide 45130 9.INSTALL HORN BUTTON ASSEMBLY

Hide 11.INSPECT SRS WARNING LIGHT

Z101186

Click here(Click here)

Hide 12. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART