Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CURTAIN SHIELD AIRBAG ASSEMBLY › from 2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443939 CURTAIN SHIELD AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CURTAIN SHIELD AIRBAG ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B620254N02
5.625,3.229 6.375,3.396 0.75,0.167 5.583,3.188 6.417,3.438 0.833,0.25 6.49,0.188 6.885,0.188 false 6.479,0.51 6.813,0.51 false 6.51,0.844 6.844,0.844 false 3.417,3.094 3.917,3.094 false 2.25,2 2.583,2 false 4.854,3.021 5.188,3.021 false 6,2.885 6,3.219 false 5.646,2.865 5.979,2.865 false 6.323,0.021 6.604,0.323 0.281,0.302 18 false 5 6.021,0.344 6.604,0.594 0.583,0.25 18 false 4, 6 6.354,0.677 6.635,0.979 0.281,0.302 18 false 3 3.229,2.896 3.51,3.198 0.281,0.302 18 false 1 2.083,1.813 2.365,2.063 0.281,0.25 18 false 2 4.552,2.927 5.042,3.094 0.49,0.167 10 false ● *1 6.104,2.771 6.594,2.938 0.49,0.167 10 false x4 5.292,2.927 5.781,3.094 0.49,0.167 10 false x3 5.635,3.24 6.396,3.406 0.76,0.167 8 false 14.0 (143, 10) 5.51,2.771 6,2.938 0.49,0.167 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CURTAIN SHIELD AIR BAG ASSEMBLY 62170A (Click here) - -
2 ROOF HEADLINING ASSEMBLY 63310 - - -
3 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
4 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
5 INSPECT SRS WARNING LIGHT - (Click here) - -
6 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

*1 ROOF SIDE INNER GARNISH CLIP - -
V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) ● Non-reusable part

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.

·

Use the same procedure for the LH and RH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 62170A 1.INSTALL CURTAIN SHIELD AIR BAG ASSEMBLY

a.
B620238C04
1.25,0.875 0.438,0.875 true 0.26,0.771 0.573,0.927 0.313,0.156 10 false *a 4.615,0.104 4.896,0.458 0.281,0.354 18 false ii 0.167,0.094 0.448,0.448 0.281,0.354 18 false i 3.01,1.76 3.24,1.969 0.229,0.208 12 false *A 1.823,1.76 2.063,1.979 0.24,0.219 12 true *B
*A w/ Entry and Start System *B w/o Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B620255C02
1.438,5.188 1.99,5.406 1.99,5.406 1.833,5.177 true 1.885,0.625 2.531,1.271 2.531,1.271 3.333,0.885 true 3.875,0.635 4.792,1.271 4.792,1.271 5.552,0.948 true 0.385,0.083 0.542,0.333 0.156,0.25 18 true i 6.802,3.188 6.969,3.448 0.167,0.26 18 true ii 0.99,4.073 1.26,4.344 0.271,0.271 18 false iii 2.365,2.344 2.573,2.542 0.208,0.198 10 true *1 4.938,4.073 5.208,4.313 0.271,0.24 18 false iv 2.031,5.365 2.344,5.563 0.313,0.198 10 false *a 4.729,1.292 5.042,1.49 0.313,0.198 10 false *b 2.448,1.281 2.76,1.479 0.313,0.198 10 false *b 2.542,2.854 2.823,3.208 0.281,0.354 18 false ii 2.875,2.854 3.156,3.208 0.281,0.354 18 false ii 0.76,2.229 0.927,2.469 0.167,0.24 18 true ii 4.865,2.5 5.073,2.698 0.208,0.198 10 true *1 4.292,2.427 4.5,2.625 0.208,0.198 10 true *1
*1 Roof Side Inner Garnish Clip - -
*a Claw (A) *b Claw (B)
V113147

Install in this Direction - -


i.

Engage the hooks and claws (B) to temporarily install the curtain shield airbag assembly.

NOTICE:

Do not twist the curtain shield airbag assembly when installing it.



ii.

Install the 4 new bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


iii.

Install the curtain shield airbag assembly with new roof side inner garnish clips.

HINT:

Engage the claws(A) to install each new roof side inner garnish clip.



iv.

Push the pins into the roof side inner garnish clips.

NOTICE:
·

Do not damage the pins.

·

Make sure that the pins of the roof side inner garnish clips are pushed in firmly.





c.
B620252N02
3.281,0.49 3.417,0.74 0.135,0.25 18 true i

i.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




Hide 63310 2.INSTALL ROOF HEADLINING ASSEMBLY

Hide 3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 5.INSPECT SRS WARNING LIGHT

Z101186

Click here(Click here)

Hide 6. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART