Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › from 2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443941 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B620275N01
0.271,0.135 1.104,0.302 0.833,0.167 0.229,0.094 1.146,0.344 0.917,0.25 6.344,2.25 6.677,2.25 false 6.5,0.208 6.865,0.208 false 6.5,0.604 6.781,0.604 false 5.167,3.417 5.75,3.417 true 1.896,0.5 2.313,0.5 false 6.5,1.042 6.823,1.042 false 1.104,0.219 1.438,0.219 false 6.281,0.042 6.563,0.396 0.281,0.354 18 false 7 5.427,0.448 6.563,0.802 1.135,0.354 18 false 5, 6, 8, 9 6.719,2.104 7,2.458 0.281,0.354 18 false 3 5.802,3.25 6.083,3.604 0.281,0.354 18 false 2 2.594,0.344 2.875,0.698 0.281,0.354 18 false 1 1.552,0.208 1.865,0.406 0.313,0.198 10 false x3 2.469,3.406 2.781,3.604 0.313,0.198 10 false x2 6.271,0.875 6.552,1.229 0.281,0.354 18 false 4 0.323,0.135 2.042,0.292 1.719,0.156 8 false 17.5 (178, 13)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 AIR BAG SENSOR ASSEMBLY 89170 (Click here) - -
2 FRONT FLOOR CARPET ASSEMBLY 58510D - - -
3 REAR CONSOLE BOX ASSEMBLY 58910C - - -
4 CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
5 UPDATE ECU SECURITY KEY - - - (Click here)
6 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
7 INSPECT SRS WARNING LIGHT - (Click here) - -
8 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)
9 PERFORM SYSTEM INITIALIZATION AND CALIBRATION - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

NOTICE:
·

After replacing the airbag ECU assembly, make sure to perform ECU configuration.

·

After performing the ECU configuration procedure, make sure to perform the initialization procedure for when the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal.



PROCEDURE

Hide 89170 1.INSTALL AIR BAG SENSOR ASSEMBLY

a.
B620238C01
0.396,0.781 1.333,0.781 true 0.333,0.094 0.615,0.448 0.281,0.354 18 false i 4.604,0.094 4.885,0.448 0.281,0.354 18 false ii 0.198,0.677 0.479,1.031 0.281,0.354 10 false *a 1.865,1.792 2.115,2.021 0.25,0.229 12 true *B 3.052,1.781 3.302,2.01 0.25,0.229 12 false *A
*A w/ Entry and Start System *B w/o Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592996N01
0.74,0.104 1.021,0.458 0.281,0.354 18 false i 3.938,0.615 4.219,0.969 0.281,0.354 18 false ii 0.76,2.677 1.042,3.031 0.281,0.354 18 false iii 2.708,1.458 2.865,1.656 0.156,0.198 10 false A 0.875,1.208 1.031,1.406 0.156,0.198 10 false B 2.344,0.135 2.5,0.333 0.156,0.198 10 false C

i.

Install the air bag sensor assembly with 3 bolts.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Temporarily tighten the 2 bolts in the order of (A), (B) and then fully tighten the 3 bolts in the order of (C), (A) and (B).

·

If the air bag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the air bag sensor assembly with a new one.

·

When installing the air bag sensor assembly, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

When the ignition switch is first turned to on (IG) after the air bag sensor assembly has been replaced, make sure that no one is in the vehicle.




ii.

Check that there is no looseness in the installed parts of the air bag sensor assembly.


iii.

Connect the 2 connectors and push in the lock lever to lock the connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.




Hide 58510D 2.INSTALL FRONT FLOOR CARPET ASSEMBLY

Hide 58910C 3.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 4.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 7.INSPECT SRS WARNING LIGHT

Z101186

Click here(Click here)

Hide 8. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART