Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › from 2021.07
RM3700E _58 Vehicle Interior _093147 SUPPLEMENTAL RESTRAINT SYSTEMS _0443956 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
B596995N03
0.208,3.813 1.208,3.979 1,0.167 0.167,3.771 1.25,4.021 1.083,0.25 6.51,0.24 6.844,0.24 false 6.417,0.563 6.75,0.563 false 1.448,3.229 1.448,2.896 false 6.448,0.885 6.781,0.885 false 0.708,3.813 0.708,2.896 false 6.365,0.104 6.646,0.458 0.281,0.354 18 false 4 5.958,0.417 6.521,0.771 0.563,0.354 18 false 3, 5 1.479,3.229 1.76,3.583 0.281,0.354 18 false 1 0.271,3.813 1.271,3.979 1,0.167 8 false 7.8 (80, 69 in.*lbf) 6.271,0.76 6.552,1.115 0.281,0.354 18 false 2

Procedure Part Name Code
Z101186

Z101188

Z101187

1 FRONT AIRBAG SENSOR 89174A (Click here) - -
2 CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 PERFORM DIAGNOSTIC SYSTEM CHECK - - - (Click here)
4 INSPECT SRS WARNING LIGHT - (Click here) - -
5 INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL - - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 89174A 1.INSTALL FRONT AIRBAG SENSOR

a.
B620238C14
1.354,0.802 0.354,0.802 true 0.146,0.688 0.458,0.844 0.313,0.156 10 false *a 4.615,0.104 4.896,0.458 0.281,0.354 18 false ii 0.167,0.094 0.448,0.448 0.281,0.354 18 false i 3.031,1.781 3.406,2.021 0.375,0.24 12 false *A 1.813,1.76 2.083,1.99 0.271,0.229 12 true *B
*A w/ Entry and Start System *B w/o Entry and Start System
*a Illumination off - -


i.

Check that the ignition switch is off.


ii.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


·

If the airbag deploys for any reason, it may cause a serious accident.





b.
B592999N01
0.344,0.021 1.719,0.375 1.375,0.354 18 false i, ii 2.521,0.021 3.896,0.375 1.375,0.354 18 false iii 5.115,0.021 6.49,0.375 1.375,0.354 18 false iv

i.

Engage the claw to hold the front airbag sensor in place.

NOTICE:

If the front airbag sensor has been dropped, replace it with a new one.



ii.

Install the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)

NOTICE:
·

When installing the front airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the nut while holding the front airbag sensor because the front airbag sensor guide is easily damaged.




iii.

Check that there is no looseness in the installation parts of the front airbag sensor.


iv.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR




Hide 2.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.INSPECT SRS WARNING LIGHT

Z101186

Click here(Click here)

Hide 5. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART