Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C143A7E  ABS Solenoid Control Actuator Stuck On  C143A7F  ABS Solenoid Control Actuator Stuck Off  


DESCRIPTION

The ABS solenoid relay built into the skid control ECU (brake booster with master cylinder assembly) supplies power to the holding solenoid and reduction solenoid.

The ABS solenoid relay is operated 1.5 seconds after the ignition switch is turned ON, and is turned off if an open or short in the ABS solenoid is detected during self-diagnosis when the vehicle starts driving.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C143A7E ABS Solenoid Control Actuator Stuck On When operation of the ABS solenoid relay is not requested, the ABS solenoid relay operates (+BS terminal voltage is 3.5 V or more) for 4.5 seconds or more. Skid control ECU (brake booster with master cylinder assembly) Brake/EPB A
C143A7F ABS Solenoid Control Actuator Stuck Off Any of the following is detected:
·

When the ignition switch ON (READY):

When the IGR terminal voltage is 9.5 V or more and operation of the ABS solenoid relay is requested, the ABS solenoid relay does not operate (+BS terminal voltage is less than 3.5 V) for 0.2 seconds or more.

·

When the ignition switch is off:

When operation of the ABS solenoid relay is requested, the ABS solenoid relay does not operate (+BS terminal voltage is less than 3.5 V) for 0.2 seconds or more.


·

Wire harness or connector

·

Skid control ECU (brake booster with master cylinder assembly)


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When DTCs C12C014 and/or C12C017 are output together with C143A7E and/or C143A7F, inspect and repair the trouble areas indicated by C12C014 and/or C12C017 first.

for C12C014: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>C12C014

for C12C017: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>C12C017


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BS TERMINAL)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-52 (BS) - Body ground Always 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A95 brake actuator assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,A95)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A38-14 (+BS) - A95-5 (+BS) Always Below 1 Ω
A38-14 (+BS) or A95-5 (+BS) - Body ground Always 10 kΩ or higher
A38-48 (SFRH) - A95-28 (SFRH) Always Below 1 Ω
A38-48 (SFRH) or A95-28 (SFRH) - Body ground Always 10 kΩ or higher
A38-49 (SFLH) - A95-31 (SFLH) Always Below 1 Ω
A38-49 (SFLH) or A95-31 (SFLH) - Body ground Always 10 kΩ or higher
A38-50 (SRRH) - A95-30 (SRRH) Always Below 1 Ω
A38-50 (SRRH) or A95-30 (SRRH) - Body ground Always 10 kΩ or higher
A38-51 (SRLH) - A95-29 (SRLH) Always Below 1 Ω
A38-51 (SRLH) or A95-29 (SRLH) - Body ground Always 10 kΩ or higher
A38-44 (SFRR) - A95-18 (SFRR) Always Below 1 Ω
A38-44 (SFRR) or A95-18 (SFRR) - Body ground Always 10 kΩ or higher
A38-45 (SFLR) - A95-15 (SFLR) Always Below 1 Ω
A38-45 (SFLR) or A95-15 (SFLR) - Body ground Always 10 kΩ or higher
A38-46 (SRRR) - A95-16 (SRRR) Always Below 1 Ω
A38-46 (SRRR) or A95-16 (SRRR) - Body ground Always 10 kΩ or higher
A38-47 (SRLR) - A95-17 (SRLR) Always Below 1 Ω
A38-47 (SRLR) or A95-17 (SRLR) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC

Pre-procedure1

a.

Reconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Reconnect the A95 brake actuator assembly connector.


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C143A7E and C143A7F are not output A
C143A7E or C143A7F is output B


HINT:
·

If a speed signal of 20 km/h (12 mph) or more is sent to the skid control ECU (brake booster with master cylinder assembly) with the ignition switch ON and the stop light switch assembly off, the ECU performs self-diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake booster with master cylinder assembly).

·

If any DTCs are output while jiggling a connector or wire harness from the brake booster with master cylinder assembly, inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.




Post-procedure1

a.

None



A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY