Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for HV Model TMC Made RHD) › from 2021.07
RM3700E _54 Brake _093767 BRAKE SYSTEM (OTHER) _0480877 BRAKE BOOSTER(for HV Model TMC Made RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for HV Model TMC Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442470N01
6.521,0.188 6.854,0.188 false 5.208,0.917 5.542,0.917 false 3.594,1.281 3.927,1.281 false 4.521,2.083 4.854,2.083 false 4.094,3.333 4.427,3.333 false 6.313,0.052 6.594,0.406 0.281,0.354 18 false 1 5.615,0.781 5.896,1.135 0.281,0.354 18 false 2 4,1.146 4.281,1.5 0.281,0.354 18 false 3 4.938,1.948 5.219,2.302 0.281,0.354 18 false 4 4.51,3.188 4.792,3.542 0.281,0.354 18 false 5 1.958,1.448 2.25,1.646 0.292,0.198 10 false x12

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 WINDSHIELD WIPER MOTOR AND LINK - - - -
3 FRONT NO. 1 VENTILATOR SEAL 55815E - - -
4 WATER GUARD PLATE LH 55735A - - -
5 OUTER COWL TOP PANEL SUB-ASSEMBLY 55701J - - -

C467502N01
6.458,0.219 6.792,0.219 false 6.448,0.719 6.781,0.719 false 1.854,0.5 2.333,0.5 false 5.281,3.448 5.448,3.229 5.448,3.229 5.615,3.229 false 4.302,3.802 4.51,4.24 4.51,4.24 4.844,4.24 false 3.76,4.188 4.24,4.188 false 4.604,4.24 4.375,3.729 true 4.708,4.229 4.458,3.635 true 6.229,0.083 6.51,0.438 0.281,0.354 18 false 6 6.229,0.573 6.51,0.927 0.281,0.354 18 false 7 2.677,0.396 2.958,0.75 0.281,0.354 18 false 8 5.667,3.063 5.948,3.417 0.281,0.354 18 false 9 5.115,4.115 5.479,4.469 0.365,0.354 18 false 11 3.26,4.094 3.417,4.292 0.156,0.198 10 false ● 3.438,4.052 3.802,4.406 0.365,0.354 18 false 10

Procedure Part Name Code
Z101186

Z101188

Z101187

6 PERFORM ACCUMULATOR PRESSURE ZERO DOWN - (Click here) - -
7 DRAIN BRAKE FLUID - - (Click here) -
8 ENGINE ROOM MAIN WIRE 82111 (Click here) - -
9 NO. 2 BRAKE ACTUATOR HOSE 44572C - - -
10 NO. 4 BRAKE TUBE CLAMP 47374B - - -
11 BRAKE LINE - (Click here) - -

● Non-reusable part - -

C463596N01
4.5,0.865 4.833,0.865 false 3.396,2.156 3.729,2.156 false 5.406,3.698 5.74,3.698 false 4.917,4.781 5.25,4.781 false 3.104,4.708 3.229,5.052 3.229,5.052 3.396,5.052 false 2.854,2.479 3.188,2.479 false 3.76,2.063 4.313,2.417 0.552,0.354 18 false 13 5.302,4.615 5.854,4.969 0.552,0.354 18 false 14 3.708,4.917 4.26,5.271 0.552,0.354 18 false 15 5.958,3.531 6.51,3.885 0.552,0.354 18 false 16 5.083,0.698 5.635,1.052 0.552,0.354 18 false 12 5.729,3.958 6.083,4.177 0.354,0.219 10 false x4 5.813,3.604 6.167,3.823 0.354,0.219 10 false ● 3.25,2.385 3.604,2.604 0.354,0.219 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

12 NO. 1 AIR DUCT 87211 (Click here) - -
13 BRAKE PEDAL RETURN SPRING 47101A - - -
14 PUSH ROD PIN 47264A - - -
15 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L (Click here) - -
16 BRAKE BOOSTER GASKET 44785 - - -

● Non-reusable part - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during brake booster with master cylinder assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Skid control ECU (brake booster with master cylinder assembly)
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Update ECU security key Vehicle control history (RoB) are stored (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



NOTICE:

While the auxiliary battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected.


HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

Z101186

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

(Click here)



Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55815E 3.REMOVE FRONT NO. 1 VENTILATOR SEAL

Hide 55701J 5.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 6.PERFORM ACCUMULATOR PRESSURE ZERO DOWN

a.
C442435N01
0.448,0.073 0.729,0.427 0.281,0.354 18 false i

i.

Using the GTS, perform the accumulator pressure zero down.

1. Connect the GTS to the DLC3 with the ignition switch off.

2. Turn the ignition switch to ON.

3. Turn the GTS on and enter the following menus: Chassis / Brake/EPB / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617

4. Select "Motor Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.

5. Perform "Motor Invalid" according to the display on the GTS.

6. Enter the following menus: Chassis / Brake/EPB / Utility / ECB (Electronically Controlled Brake system) Utility.

Chassis > Brake/EPB > Utility
Tester Display
ECB Utility
50005 435 2617

7. Select "ECB (Electronically Controlled Brake system) Invalid" on the "ECB (Electronically Controlled Brake system) Utility" screen.

8. Perform "ECB (Electronically Controlled Brake system) Invalid" according to the display on the GTS.

9. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

HINT:

A buzzer may sound due to low accumulator pressure. As this is not a malfunction, continue the procedure.


10. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.


11. Turn the GTS off and turn the ignition switch off.

12. Disconnect the GTS from the DLC3.

13. Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL



b.

When the accumulator pressure zero down could not be performed using the GTS:

C442473C02
0.344,0.031 0.625,0.385 0.281,0.354 18 false i
V113147

Release the lock lever
V113148

Disconnect the connector


i.

If DTCs are output, accumulator pressure zero down may not be complete. In this case, perform the following procedure.

1. With the ignition switch off, release the lock lever and disconnect the brake booster pump assembly connector as shown in the illustration.

2. Depress the brake pedal 40 times or more to return all the fluid in the accumulator back to the reservoir.

3. Check that the brake pedal is firm.

NOTICE:

If the brake pedal is not firm or the pump motor continues to operate even after depressing the brake pedal 40 times or more, the accumulator pressure zero down is not complete.


4. Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL



Hide 7.DRAIN BRAKE FLUID

Z101186

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.



Hide 82111 8.REMOVE ENGINE ROOM MAIN WIRE

a.
C442474C02
3.469,2.646 3.333,2.333 true 3.833,2.667 4,2.667 4,2.667 4.042,2.49 true 4.219,2.375 4.333,2.333 true 5.5,2.75 5.417,2.75 5.417,2.75 5.417,2.583 true 6.427,2.708 6.333,2.417 6.333,2.417 6.167,2.417 true 1.813,2.281 2.01,2.531 0.198,0.25 18 true i 0.708,1.646 0.958,1.896 0.25,0.25 18 true ii 3.406,2.656 3.615,2.844 0.208,0.188 10 false *a 3.844,2.229 4.052,2.417 0.208,0.188 10 false *c 3.677,2.594 3.885,2.781 0.208,0.188 10 false *b 4.344,2.24 4.552,2.427 0.208,0.188 10 false *a 5.531,2.656 5.74,2.844 0.208,0.188 10 false *d 5.979,2.333 6.188,2.521 0.208,0.188 10 false *e 2.688,0.313 2.938,0.563 0.25,0.25 18 true iii 5.125,0.302 5.375,0.552 0.25,0.25 18 true iv 6.365,1.177 6.615,1.427 0.25,0.25 18 true v
*a Lock Lever *b Lock Arm
*c Push *d Screwdriver Insertion Point
*e Pre-lock - -
V113147

Release the lock lever
V113148

Disconnect the connector


i.

Disconnect the connector from the brake booster with master cylinder assembly.


ii.

Disengage the clamp.


iii.

Push the lock arm of the connector to release the lock and rotate the lock lever to the position shown in the illustration.


iv.

Using a screwdriver, release the pre-lock and disconnect the connector from the brake booster with master cylinder assembly as shown in the illustration.


v.

Disengage the clamp to separate the engine room main wire.



Hide 44572C 9.DISCONNECT NO. 2 BRAKE ACTUATOR HOSE

a.
C429876


Hide 47374B 10.REMOVE NO. 4 BRAKE TUBE CLAMP

a.
C430395


Hide 11.DISCONNECT BRAKE LINE

a.
C442475N01
0.365,0.042 0.583,0.292 0.219,0.25 18 false i

i.

Using a union nut wrench, disconnect the 3 brake lines from the brake booster with master cylinder assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.





Hide 87211 12.REMOVE NO. 1 AIR DUCT

Z101186

Click here(Click here)

Hide 47101A 13.REMOVE BRAKE PEDAL RETURN SPRING

Hide 47210L 15.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

a.
C442476N01
0.344,0.042 0.625,0.396 0.281,0.354 18 false i

i.

Remove the 4 nuts and brake booster with master cylinder assembly.

NOTICE:
·
C429884C02
1.375,0.688 1.375,0.438 1.375,0.438 1.208,0.438 false 1.76,0.594 2.094,0.594 false 0.51,1.667 0.51,1.333 false 0.771,1.167 0.771,0.917 0.771,0.917 0.604,0.917 false 2.302,1.771 2.302,1.438 false 1.771,0.76 2.104,0.76 false 1.021,0.375 1.333,0.573 0.313,0.198 10 false *1 2.146,0.542 2.458,0.74 0.313,0.198 10 false *2 0.438,1.667 0.75,1.865 0.313,0.198 10 false *3 0.427,0.854 0.74,1.052 0.313,0.198 10 false *4 2.219,1.792 2.531,1.99 0.313,0.198 10 false *5 2.146,0.719 2.458,0.917 0.313,0.198 10 false *6
*1 Skid Control ECU
*2 No. 1 Reservoir Hose
*3 Brake Master Cylinder Push Rod Clevis
*4 Boot
*5 Master Cylinder Reservoir Assembly
*6 Brake Actuator Bracket


Do not kink or damage the brake lines.

·

Do not carry the brake booster with master cylinder assembly by the parts shown in the illustration.

·

Be careful not to allow any brake fluid to enter the connector.





Hide 44785 16.REMOVE BRAKE BOOSTER GASKET

a.
C429885