The airbag sensor assembly has a built-in yaw rate and acceleration sensor.
If a power source malfunction signal from the yaw rate and acceleration sensor (airbag sensor assembly) is detected by the skid control ECU (brake booster with master cylinder assembly), DTC C14D71C is stored.
DTC C14D71C may be stored due to an intermittent low power source voltage.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C14D71C | Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range | At a vehicle speed of more than 3 km/h (2 mph), the acceleration sensor power source malfunction signal is received for 10 seconds or more. | ·
Wire harness or connector ·
Acceleration sensor (airbag sensor assembly) |
Brake/EPB | A |
After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration after clearing previously calibrated data.
Inspect the fuses for circuits related to this system before performing the following procedure.
Pre-procedure1
Turn the ignition switch off.
Procedure1
Make sure that there is no looseness at the locking part and the connecting part of the connector.
The connector is securely connected.
Pre-procedure2
Disconnect the H14 yaw rate and acceleration sensor (airbag sensor assembly) connector.
Procedure2
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Pre-procedure3
Turn the ignition switch to ON.
Procedure3
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H14)Location & Routingewd_type=routing;type=c;code=H14 Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assemblyewd_type=component;type=c;code=H14;pinno=36 |
||
| H14-36 (IGR) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Turn the ignition switch off.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(H14)Location & Routingewd_type=routing;type=c;code=H14 Click Connector(H14)Instrument Panel>Instrument Panel Wire / Speaker Wire>Airbag Sensor Assemblyewd_type=component;type=c;code=H14;pinno=33,32 |
||
| H14-33 (E1) - Body ground | Always | Below 1 Ω |
| H14-32 (E2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Reconnect the H14 yaw rate and acceleration sensor (airbag sensor assembly) connector.
Procedure1
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
Post-procedure1
Turn the ignition switch off.
NEXT
Pre-procedure1
Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.
Procedure1
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C14D71C is not output | A |
| C14D71C is output | B |
Post-procedure1
None
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B