Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  C14FE14  Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C14FE14 Steering Angle Sensor Supply Voltage Circuit Circuit Short to Ground or Open Steering sensor power supply malfunction signal is received from steering sensor.
·

Wire harness or connector

·

Steering sensor


Brake/EPB A

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

2.RECONFIRM DTC
2.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Check if the same DTC is output.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C14FE14 is not output A
C14FE14 is output B



Post-procedure1

a.

None



A

B

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

Pre-procedure1

a.

Remove the steering wheel and column cover.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the H39 steering sensor connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-4 (BAT) - Body ground Always 11 to 14 V
H39-9 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

NOTICE:

Before measuring the resistance of the steering sensor, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or switches, or opening or closing the doors.


Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-6 (ESS) - Body ground 1 minute after ignition switch off Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)