Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  Brake Hold Standby Indicator Light Circuit  


DESCRIPTION

The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (electric parking brake switch assembly) is turned on while the power switch is on (IG).

Conditions required for operation standby:

(a)

The driver side door is closed.

(b)

The driver side seat belt is fastened.

(c)

The system is normal.



WIRING DIAGRAM

C378328E18
0.917,0.635 1.531,0.833 0.615,0.198 10 false CANL 5.542,0.646 6.156,0.844 0.615,0.198 10 false CA1L 0.906,1.448 1.521,1.646 0.615,0.198 10 false CANH 5.542,1.458 6.156,1.656 0.615,0.198 10 false CA1H 5.271,0.469 5.583,0.667 0.313,0.198 10 false 42 5.271,1.281 5.583,1.479 0.313,0.198 10 false 43 1.385,0.469 1.698,0.667 0.313,0.198 10 false 25 1.385,1.281 1.698,1.479 0.313,0.198 10 false 9 5.281,3.083 5.594,3.281 0.313,0.198 10 false 24 5.542,3.073 6,3.271 0.458,0.198 10 false CTY 6.615,3.156 6.927,3.354 0.313,0.198 10 false IC 6.615,4.979 6.927,5.177 0.313,0.198 10 false IC 5.271,4.896 5.583,5.094 0.313,0.198 10 false 20 5.531,4.896 6.146,5.094 0.615,0.198 10 false CSW2 0.073,1.99 0.865,2.198 0.792,0.208 10 false H6 0.063,2.156 1.958,2.542 1.896,0.385 10 false Combination Meter Assembly 2.406,2.083 4.208,2.813 1.802,0.729 10 false to Main Body ECU (Multiplex Network Body ECU) 3.792,3.083 3.948,3.281 0.156,0.198 10 false 1 3.792,4.906 4.219,5.156 0.427,0.25 10 false 10 2.344,3.521 2.802,3.719 0.458,0.198 10 false O40 2.344,3.698 4.375,4.25 2.031,0.552 10 false Front Door Courtesy Light Switch Assembly RH 3.521,4.906 3.833,5.104 0.313,0.198 10 false +B 2.927,4.906 3.542,5.104 0.615,0.198 10 false E 2.646,4.906 2.875,5.104 0.229,0.198 10 false 12 2.271,5.354 2.729,5.552 0.458,0.198 10 false H140 2.271,5.521 4.469,6.042 2.198,0.521 10 false Brake Hold Switch (Electric Parking Brake Switch Assembly) 0.615,6.219 2.438,6.521 1.823,0.302 10 false : CAN Communication Line 5.094,5.823 5.74,6.021 0.646,0.198 10 false A38 5.083,6 7.135,6.406 2.052,0.406 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform linear solenoid valve offset learning, ABS holding solenoid valve learning, yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.PRE-CHECK
a.

If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.

1.

The driver side door is closed.

2.

The driver side seat belt is fastened.

3.

The system is normal.


HINT:

If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.

·

Brake system

·

Electric parking brake system

·

Hybrid control system



Result:
Proceed to
NEXT




NEXT

2.CHECK CAN COMMUNICATION SYSTEM
2.CHECK CAN COMMUNICATION SYSTEM

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

3.CHECK IF BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

CONNECT CONNECTOR TO BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY CORRECTLY

4.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform the Active Test of the combination meter assembly using the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display
Brake Hold Indicator
50004 409 117

c.

Check the combination meter assembly.

OK:

The brake hold standby indicator light turns on or off in accordance with GTS operation.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (BRAKE HOLD READY)

NG

5.READ VALUE USING GTS (BRAKE HOLD READY)
a.

Check the brake hold standby indicator light and mode condition on the GTS changes according to brake hold switch (electric parking brake switch assembly) operation.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated)
-
Chassis > Brake/EPB > Data List
Tester Display
Brake Hold Ready
50003 435 164
Standard:
Brake Hold Switch (Electric Parking Brake Switch Assembly) Operation Mode Condition Display Brake Hold Standby Indicator Light
Not pressed Not in stand-by mode Does not come on
Pressing the brake hold switch (electric parking brake switch assembly) Stand-by mode Come on



Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display are normal C



A

6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

B

C

6.INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY
a.

Turn the ignition switch off.


b.

Inspect the brake hold switch (electric parking brake switch assembly).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE HOLD SWITCH>INSPECTION

OK:

The brake hold switch (electric parking brake switch assembly) operates normally.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A38,H140)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

Click Connector(H140)Instrument Panel>Instrument Panel Wire / Speaker Wire>Electric Parking Brake Switch Assembly

A38-20 (CSW2) - H140-10 (+B) Always Below 1 Ω
A38-20 (CSW2) or H140-10 (+B) - Body ground Always 10 kΩ or higher
H140-12 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Turn on the interior lights and check that they illuminate, and then set the switch so that the lights illuminate when the door is opened.


b.

Check that the lights illuminate when the driver side door is opened.

OK:

The interior lights illuminate when the driver side door is opened.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)

NG

INSPECT LIGHTING SYSTEM (COURTESY LIGHT SWITCH CIRCUIT)

9.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-24 (CTY) - Body ground Driver door open 1.5 V or less
A38-24 (CTY) - Body ground Driver door closed 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CTY CIRCUIT)