Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484411 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMC Made)  Abnormal Brake Pedal Response on First Depression  


DESCRIPTION

If the vehicle has been stopped without opening or closing the driver door for a long period of time, the electronically controlled brake system will not be ready and sufficient fluid pressure may not be stored in the accumulator. In this case, the brake pedal response may not be the same as usual the first time the brake pedal is depressed. This is not a malfunction.

WIRING DIAGRAM

C350988E34
5.115,2.021 5.594,2.354 0.479,0.333 10 false 24 5.375,2.01 5.854,2.344 0.479,0.333 10 false CTY 6.333,2.104 6.813,2.438 0.479,0.333 10 false IC 5.021,3.875 5.5,4.208 0.479,0.333 10 false A38 5.01,4.042 7.083,4.5 2.073,0.458 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.521,1.104 2.333,1.563 1.813,0.458 10 false to Main Body ECU (Multiplex Network Body ECU) 2.417,2.51 2.896,2.844 0.479,0.333 10 false O40 3.573,2.01 4.052,2.344 0.479,0.333 10 false 1 2.365,2.667 5.313,3 2.948,0.333 10 false Front Door Courtesy Light Switch Assembly RH

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake booster with master cylinder assembly), perform "Calibration" after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY


PROCEDURE

1.BRAKE PROBLEM CHECK
a.

Check the conditions at the time the problem occurred.

i.

Whether a warning light illuminated or the buzzer sounded.


ii.

The number of times the ignition switch was turned ON since the latest symptom occurred.


iii.

Frequency of the symptom.



Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Check the DTCs (electronically controlled brake system) that are output.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs C125600, C125609 and C139100 are not output. A
DTCs C125600, C125609 and/or C139100 are output. B



A

4.CHECK VEHICLE

B

4.CHECK VEHICLE
a.

Turn the ignition switch off.


b.

Depress the brake pedal within 3 minutes of opening the driver door and check the response of the brake pedal.


c.

Release the brake pedal and wait for 3 minutes without depressing the brake pedal, opening or closing the driver door or operating the ignition switch.


d.

After 3 seconds or more have elapsed, depress the brake pedal and check that the first depression response is different to successive depression responses.

HINT:

Compare the response of the brake pedal when the system is in sleep mode and when the stroke simulator is operating.



Result:
Result Proceed to
The response of the brake pedal does not change. A
The response of the brake pedal changed. B



A

5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR DRIVER SIDE)

B

END

5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (FOR DRIVER SIDE)
a.

Set the interior light door switch to ON and check that the map light assembly illuminates, then set the interior light door switch to DOOR.


b.

Check that the map light assembly illuminates when the driver door is opened.

OK:

The map light assembly illuminates when the driver door is opened.



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)

NG

6.CHECK HARNESS AND CONNECTOR (CTY TERMINAL)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A38)Location & Routing

Click Connector(A38)Engine Compartment>Engine Room Main Wire>Brake Booster with Master Cylinder Assembly

A38-24 (CTY) - Body ground Driver door open 1.5 V or less
A38-24 (CTY) - Body ground Driver door closed 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR