Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C05121F  Right Rear Wheel Speed Sensor Circuit Intermittent  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for brake control.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.

Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C445802E01
1.573,1.073 1.094,0.667 true 6.094,1.156 6.594,1.323 0.5,0.167 10 false 1.4 V 6.094,1.479 6.604,1.635 0.51,0.156 10 false 0.7 V 0.167,0.552 1.188,0.885 1.021,0.333 10 false Speed Sensor 4.01,1.979 4.938,2.208 0.927,0.229 10 false Low speed 4.958,1.99 6.073,2.302 1.115,0.313 10 false High speed 1.021,2.313 2.646,2.667 1.625,0.354 10 false Speed Sensor Rotor

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C05121F Right Rear Wheel Speed Sensor Circuit Intermittent Any of the following is detected:
·

When the +BS terminal voltage is 17.4 V or less, an open in the sensor signal circuit of a malfunctioning area occurs 255 times or more.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 20 km/h (12 mph) or more, noise occurs in the sensor signals of a malfunctioning wheel 75 times or more within 5 seconds.

·

When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per rotor rotation for 15 seconds or more.


·

Rear speed sensor RH (rear axle hub and bearing assembly RH)

·

Sensor installation

·

Skid control sensor wire RH (No. 1 parking brake wire assembly)

·

Wire harness and connector

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Skid control ECU (brake actuator assembly)


Brake/EPB A

WIRING DIAGRAM

C467243E01
0.573,2.219 2.01,2.802 1.438,0.583 10 false Rear Speed Sensor RH (Rear Axle Hub and Bearing Assembly RH) 2.365,2.208 3.51,2.729 1.146,0.521 10 false Skid Control Sensor Wire RH 5.167,3.167 6.76,3.802 1.594,0.635 10 false Skid Control ECU (Brake Actuator Assembly) 5.25,1.031 5.75,1.271 0.5,0.24 10 false RR+ 3.198,1.125 3.646,1.385 0.448,0.26 10 false RR+ 1.76,1.104 2.177,1.344 0.417,0.24 10 false + 2.438,1.125 2.927,1.375 0.49,0.25 10 false RR+ 1.771,1.802 2.167,2.042 0.396,0.24 10 false - 2.438,1.833 2.917,2.01 0.479,0.177 10 false RR- 3.219,1.833 3.677,2.021 0.458,0.188 10 false RR- 5.25,1.708 5.75,1.917 0.5,0.208 10 false RR- 2.052,1.104 2.604,1.344 0.552,0.24 10 false u2 2.052,1.792 2.385,2.042 0.333,0.25 10 false u2 3.615,1.115 4.104,1.333 0.49,0.219 10 false uO1 3.604,1.802 4.021,2.104 0.417,0.302 10 false uO1 2.094,1.615 2.396,1.844 0.302,0.229 10 false 1 5.167,3 5.667,3.198 0.5,0.198 10 false A94 2.104,0.917 2.406,1.146 0.302,0.229 10 false 2 3.698,0.917 4,1.146 0.302,0.229 10 false 4 3.698,1.615 4,1.844 0.302,0.229 10 false 3 4.99,1.01 5.281,1.25 0.292,0.24 10 false 20 4.99,1.698 5.344,1.948 0.354,0.25 10 false 19

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TEST MODE PROCEDURE



PROCEDURE

1.READ VALUE USING GTS (RR SPEED SENSOR VOLTAGE OPEN)

Pre-procedure1

a.

Select the line graph display on the GTS.


Procedure1

a.

Check for any momentary interruption in the wire harness and connector.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Speed Sensor Voltage Open Rear speed sensor RH voltage open detection Under intermittent / Normal Under intermittent: Momentary interruption detected
Normal: Momentary interruption not detected
-
Chassis > Brake/EPB > Data List
Tester Display
RR Speed Sensor Voltage Open
50003 435 112
OK:

Normal (There are no momentary interruptions.)


NOTICE:

Perform the above inspection before removing the sensor and connector.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.READ VALUE USING GTS (RR WHEEL SPEED)

NG

5.CHECK REAR SPEED SENSOR RH INSTALLATION
2.READ VALUE USING GTS (RR WHEEL SPEED)

Pre-procedure1

a.

Drive the vehicle and perform a road test.


Procedure1

a.

Check the speed value output from the speed sensor displayed on the GTS.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake/EPB > Data List
Tester Display
RR Wheel Speed
50003 435 15
HINT:

Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

5.CHECK REAR SPEED SENSOR RH INSTALLATION
3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Operate the GTS to clear the codes.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

a.

Operate the GTS to read the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435
Result:
Result Proceed to
C05121F is not output A
C05121F is output B



Post-procedure1

a.

None



A

B

5.CHECK REAR SPEED SENSOR RH INSTALLATION

Pre-procedure1

a.
C210569C19
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 false *a 2.344,1.698 2.656,1.896 0.313,0.198 10 false *b 1.344,0.104 1.656,0.302 0.313,0.198 10 false *c
*a Correct
*b Incorrect
*c No clearance


Turn the ignition switch off.


Procedure1

a.

Check the rear speed sensor RH installation.

OK:

There is no clearance between the rear speed sensor RH and the rear axle hub and bearing assembly RH.


HINT:

The rear speed sensor rotor RH and rear speed sensor RH are incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor rotor RH needs to be replaced, replace the rear axle hub and bearing assembly RH with rear speed sensor RH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

6.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

6.INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the u2 and uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(u2,uO1)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

u2-2 (+) - uO1-4 (RR+) Always Below 1 Ω
u2-2 (+) or uO1-4 (RR+) - Body ground and other terminals Always 10 kΩ or higher
u2-1 (-) - uO1-3 (RR-) Always Below 1 Ω
u2-1 (-) or uO1-3 (RR-) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

7.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (NO. 1 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(uO1,A94)Location & Routing

Click Connector(uO1)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 1 Parking Brake Wire Assembly and Floor Wire

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

uO1-4 (RR+) - A94-20 (RR+) Always Below 1 Ω
uO1-4 (RR+) or A94-20 (RR+) - Body ground Always 10 kΩ or higher
uO1-3 (RR-) - A94-19 (RR-) Always Below 1 Ω
uO1-3 (RR-) or A94-19 (RR-) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT BRAKE ACTUATOR ASSEMBLY (SENSOR POWER SOURCE CIRCUIT)

Pre-procedure1

a.

Reconnect the A94 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the uO1 skid control sensor wire RH (No. 1 parking brake wire assembly) connector.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure2

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(u2)Location & Routing

Click Connector(u2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Rear Speed Sensor RH (Rear Axle Hub & Bearing Assembly RH)

u2-2 (+) - Body ground Ignition switch ON 11 to 14 V


HINT:

The rear speed sensor RH is incorporated into the rear axle hub and bearing assembly RH.

If the rear speed sensor RH needs to be replaced, replace the rear axle hub and bearing assembly RH.


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG