Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C05262A  Steering Angle Sensor Module Signal Stuck In Range  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the steering sensor via CAN communication.

HINT:

When a malfunction occurs in the communication line to the steering sensor, U012687 is output.

If a DTC related to the CAN communication line is output, first troubleshoot the CAN communication line.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C05262A Steering Angle Sensor Module Signal Stuck In Range Normal communication between the skid control ECU and the steering sensor and abnormal steering sensor zero point.
·

Steering sensor

·

Wire harness and connector


Brake/EPB A

WIRING DIAGRAM

C377599E38
6.052,0.667 6.667,0.865 0.615,0.198 10 false CANL 0.792,0.667 1.406,0.865 0.615,0.198 10 false CANL 6.042,1.25 6.656,1.448 0.615,0.198 10 false CANH 0.781,1.25 1.396,1.448 0.615,0.198 10 false CANH 5.74,0.479 6.052,0.677 0.313,0.198 10 false 43 5.74,1.063 6.052,1.26 0.313,0.198 10 false 27 1.281,0.5 1.438,0.698 0.156,0.198 10 false 8 1.281,1.083 1.438,1.281 0.156,0.198 10 false 3 1.271,1.635 1.427,1.833 0.156,0.198 10 false 4 0.917,1.729 1.375,1.927 0.458,0.198 10 false BAT 0.938,2.385 1.396,2.583 0.458,0.198 10 false IGR 0.896,3.323 1.354,3.521 0.458,0.198 10 false ESS 1.26,2.323 1.417,2.521 0.156,0.198 10 false 9 1.271,3.177 1.427,3.375 0.156,0.198 10 false 6 2.021,1.865 3.854,2.063 1.833,0.198 10 false ECU-DCC NO. 1 1.969,2.563 3.802,2.76 1.833,0.198 10 false ECU-IGR NO. 1 3.573,1.729 5.188,1.927 1.615,0.198 10 false from Auxiliary Battery 3.646,2.406 5.563,2.625 1.917,0.219 10 false from IGR-NO. 1 Relay 0.302,4 0.76,4.198 0.458,0.198 10 false H39 0.292,4.156 1.813,4.365 1.521,0.208 10 false Steering Sensor 3,3.531 5.031,3.781 2.031,0.25 10 false : CAN Communication Line 5.552,3.844 6.01,4.042 0.458,0.198 10 false A94 5.542,4.01 7.073,4.448 1.531,0.438 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Operate the GTS to clear the codes.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

2.RECONFIRM DTC (CAN COMMUNICATION SYSTEM)
2.RECONFIRM DTC (CAN COMMUNICATION SYSTEM)
a.

Check if CAN communication system DTCs are output.

HINT:

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM



Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B

3.RECONFIRM DTC
3.RECONFIRM DTC

Pre-procedure1

a.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left.


Procedure1

a.

Operate the GTS to read the DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435

b.

Check that no speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output.

HINT:
·

If a speed sensor, or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering sensor may be stored even though the steering sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair these malfunctions and then inspect the steering sensor.



Result:
Result Proceed to
Only C05262A is output A
Speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output B
None of the above conditions are met C



Post-procedure1

a.

Turn the ignition switch off.



A

4.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)

B

C

4.CHECK HARNESS AND CONNECTOR (IGR TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the H39 steering sensor connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-9 (IGR) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

5.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BAT TERMINAL)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-4 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H39)Location & Routing

Click Connector(H39)Instrument Panel>Instrument Panel Wire / Speaker Wire>Spiral Cable Sub-Assembly

H39-6 (ESS) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR