Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  C13807E  Stop Lamp Relay Actuator Stuck On  


DESCRIPTION

When any of the following conditions are met, the skid control ECU (brake actuator assembly) sets the drive output (STPO) ON which operates the stop light switch assembly and turns on the stop lights.

Illumination Conditions:
·

Pre-collision brake is operating.

·

The dynamic radar cruise control system is operating and is applying the brakes.

·

Secondary collision brake is operating.

·

Brake hold is operating.

·

The parking brake is engaged while the vehicle is being driven.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C13807E Stop Lamp Relay Actuator Stuck On When the IGR terminal voltage exceeds 10 V and the +BS terminal voltage is 9.5 V or higher, stop light drive output (STPO) is OFF, STP is OFF and STP2 is ON continuously for 5 seconds or more.
·

Wire harness and connector

·

Skid control ECU (Brake actuator assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light assembly


Brake/EPB A

WIRING DIAGRAM

C427243E24
0.125,0.135 2.698,0.375 2.573,0.24 12 false for Halogen Headlight: 1.313,0.698 2.75,0.927 1.438,0.229 10 false from IGP Relay 2.177,1.125 3.406,1.354 1.229,0.229 10 false to Each Computers 1.302,1.563 2.688,1.802 1.385,0.24 10 false from Auxiliary Battery 1.635,2.302 1.76,2.49 0.125,0.188 10 false 7 1.656,3.219 1.781,3.406 0.125,0.188 10 false 6 0.958,2.583 1.396,2.792 0.438,0.208 10 false STOP 0.667,3.5 1.677,3.719 1.01,0.219 10 false ECU-IGP NO. 3 1.646,5.01 3.5,5.26 1.854,0.25 10 false Stop Light Switch Assembly 1.656,4.823 2.021,5.031 0.365,0.208 10 false A63 1.635,4.208 1.771,4.406 0.135,0.198 10 false 2 1.844,2.427 2.208,2.635 0.365,0.208 10 false B 1.844,3.323 2.208,3.531 0.365,0.208 10 false B 1.844,4.323 2.208,4.531 0.365,0.208 10 false GND 3.115,2.417 3.313,2.625 0.198,0.208 10 false L 2.938,3.323 3.302,3.542 0.365,0.219 10 false ACC 2.948,4.323 3.313,4.542 0.365,0.219 10 false OUT 3.323,2.302 3.521,2.51 0.198,0.208 10 false 3 3.323,3.229 3.521,3.438 0.198,0.208 10 false 4 3.313,4.198 3.51,4.406 0.198,0.208 10 false 1 4.667,2.292 4.865,2.5 0.198,0.208 10 false 11 4.646,3.208 4.875,3.417 0.229,0.208 10 false 32 4.646,4.188 4.875,4.396 0.229,0.208 10 false 37 4.927,2.417 5.365,2.635 0.438,0.219 10 false STP 4.917,3.323 5.354,3.542 0.438,0.219 10 false STPO 4.917,4.313 5.354,4.531 0.438,0.219 10 false STP2 4.719,5.021 6.25,5.417 1.531,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 4.729,4.833 5.094,5.042 0.365,0.208 10 false A94 1.625,6.552 3.063,6.948 1.438,0.396 10 false Rear Combination Light Assembly LH 1.625,6.385 2.438,6.604 0.813,0.219 10 false O102 1.646,5.875 1.802,6.115 0.156,0.24 10 false 2 1.813,5.979 2.021,6.198 0.208,0.219 10 false E 2.75,5.979 2.958,6.198 0.208,0.219 10 false B 2.948,5.865 3.156,6.083 0.208,0.219 10 false 3 1.615,8.042 3.063,8.438 1.448,0.396 10 false Rear Combination Light Assembly RH 1.615,7.875 2.344,8.073 0.729,0.198 10 false O104 1.646,7.344 1.802,7.583 0.156,0.24 10 false 2 1.813,7.448 2.021,7.667 0.208,0.219 10 false E 2.75,7.438 2.958,7.656 0.208,0.219 10 false B 2.948,7.344 3.156,7.563 0.208,0.219 10 false 3 4.792,8.052 6.573,8.281 1.781,0.229 10 false Center Stop Light Assembly 4.802,7.885 5.167,8.094 0.365,0.208 10 false Q1 4.979,7.344 5.135,7.583 0.156,0.24 10 false 2 6.083,7.438 6.292,7.656 0.208,0.219 10 false E 5.156,7.427 5.365,7.646 0.208,0.219 10 false B 6.281,7.344 6.49,7.563 0.208,0.219 10 false 1

C427243E25
1.333,0.698 2.74,0.927 1.406,0.229 10 false from IGP Relay 1.313,1.563 2.74,1.813 1.427,0.25 10 false from Auxiliary Battery 2.198,1.135 3.448,1.365 1.25,0.229 10 false to Each Computers 1.625,2.302 1.781,2.5 0.156,0.198 10 false 7 3.333,2.302 3.49,2.5 0.156,0.198 10 false 3 4.656,2.292 4.927,2.5 0.271,0.208 10 false 11 4.938,2.427 5.552,2.625 0.615,0.198 10 false STP 4.938,3.333 5.552,3.531 0.615,0.198 10 false STPO 4.938,4.323 5.552,4.521 0.615,0.198 10 false STP2 4.635,3.208 4.865,3.396 0.229,0.188 10 false 32 4.646,4.198 4.896,4.396 0.25,0.198 10 false 37 3.333,3.219 3.49,3.417 0.156,0.198 10 false 4 3.333,4.198 3.49,4.396 0.156,0.198 10 false 1 1.625,3.219 1.781,3.417 0.156,0.198 10 false 6 1.625,4.198 1.781,4.396 0.156,0.198 10 false 2 3.104,2.427 3.26,2.625 0.156,0.198 10 false L 2.906,3.344 3.323,3.521 0.417,0.177 10 false ACC 2.938,4.344 3.354,4.531 0.417,0.188 10 false OUT 1.844,2.417 2,2.615 0.156,0.198 10 false B 1.865,3.333 2.021,3.531 0.156,0.198 10 false B 1.854,4.333 2.281,4.531 0.427,0.198 10 false GND 0.979,2.563 1.594,2.76 0.615,0.198 10 false STOP 0.635,3.5 2.469,3.698 1.833,0.198 10 false ECU-IGP NO. 3 1.667,4.813 2.125,5.01 0.458,0.198 10 false A63 1.667,4.99 3.542,5.26 1.875,0.271 10 false Stop Light Switch Assembly 4.74,4.813 5.198,5.01 0.458,0.198 10 false A94 4.729,4.99 6.26,5.49 1.531,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 1.625,5.865 1.781,6.063 0.156,0.198 10 false 2 2.958,5.865 3.115,6.063 0.156,0.198 10 false 3 1.833,5.979 1.99,6.177 0.156,0.198 10 false E 2.75,5.979 2.906,6.177 0.156,0.198 10 false B 1.635,6.385 2.271,6.594 0.635,0.208 10 false O106 1.635,6.552 3.073,6.948 1.438,0.396 10 false Rear Combination Light Assembly LH 1.635,7.344 1.792,7.542 0.156,0.198 10 false 2 2.958,7.344 3.115,7.542 0.156,0.198 10 false 3 4.969,7.333 5.146,7.594 0.177,0.26 10 false 2 6.292,7.333 6.49,7.625 0.198,0.292 10 false 1 1.615,7.875 2.302,8.063 0.688,0.188 10 false O109 1.604,8.052 3.042,8.469 1.438,0.417 10 false Rear Combination Light Assembly RH 1.833,7.438 1.99,7.635 0.156,0.198 10 false E 2.76,7.438 2.917,7.635 0.156,0.198 10 false B 5.177,7.438 5.333,7.635 0.156,0.198 10 false B 6.083,7.438 6.24,7.635 0.156,0.198 10 false E 4.823,7.885 5.146,8.073 0.323,0.188 10 false Q1 4.823,8.042 6.563,8.333 1.74,0.292 10 false Center Stop Light Assembly 0.167,0.146 2.156,0.344 1.99,0.198 12 false for LED Headlight:

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


PROCEDURE

1.CHECK VEHICLE SPECIFICATION
a.

Check the vehicle specification.


Result:
Result Proceed to
for Halogen Headlight A
for LED Headlight B



A

2.CHECK STOP LIGHT ILLUMINATION STATUS (FOR HALOGEN HEADLIGHT)

B

9.CHECK STOP LIGHT ILLUMINATION STATUS (FOR LED HEADLIGHT)
2.CHECK STOP LIGHT ILLUMINATION STATUS (FOR HALOGEN HEADLIGHT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A63 stop light switch assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Check the illumination status of the brake lights.

Result:
Result Proceed to
The stop lights are illuminated A
The stop lights are not illuminated B



Post-procedure1

a.

Turn the ignition switch off.



A

3.READ VALUE USING GTS (STOP LIGHT RELAY)

B

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
3.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Reconnect the A63 stop light switch assembly connector.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE STOP LIGHT SWITCH ASSEMBLY

B

4.READ VALUE USING GTS (STOP LIGHT RELAY)
4.READ VALUE USING GTS (STOP LIGHT RELAY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the O102 rear combination light assembly LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY LH (STOP LIGHT CIRCUIT))

B

5.READ VALUE USING GTS (STOP LIGHT RELAY)
5.READ VALUE USING GTS (STOP LIGHT RELAY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the O104 rear combination light assembly RH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY RH (STOP LIGHT CIRCUIT))

B

6.READ VALUE USING GTS (STOP LIGHT RELAY)
6.READ VALUE USING GTS (STOP LIGHT RELAY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the Q1 center stop light assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

B

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A94)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A94-37 (STP2) - Body ground Ignition switch ON 0 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63,A94)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A63-4 (ACC) or A94-32 (STPO) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK STOP LIGHT ILLUMINATION STATUS (FOR LED HEADLIGHT)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A63 stop light switch assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Check the illumination status of the brake lights.

Result:
Result Proceed to
The stop lights are illuminated A
The stop lights are not illuminated B



Post-procedure1

a.

Turn the ignition switch off.



A

10.READ VALUE USING GTS (STOP LIGHT RELAY)

B

15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
10.READ VALUE USING GTS (STOP LIGHT RELAY)

Pre-procedure1

a.

Reconnect the A63 stop light switch assembly connector.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

REPLACE STOP LIGHT SWITCH ASSEMBLY

B

11.READ VALUE USING GTS (STOP LIGHT RELAY)
11.READ VALUE USING GTS (STOP LIGHT RELAY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the O106 rear combination light assembly LH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

GO TO LIGHTING SYSTEM ((REAR COMBINATION LIGHT ASSEMBLY LH (STOP LIGHT CIRCUIT))

B

12.READ VALUE USING GTS (STOP LIGHT RELAY)
12.READ VALUE USING GTS (STOP LIGHT RELAY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the O109 rear combination light assembly RH connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

GO TO LIGHTING SYSTEM (REAR COMBINATION LIGHT ASSEMBLY RH (STOP LIGHT CIRCUIT))

B

13.READ VALUE USING GTS (STOP LIGHT RELAY)
13.READ VALUE USING GTS (STOP LIGHT RELAY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the Q1 center stop light assembly connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



b.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Relay STP2 terminal input OFF / ON OFF: STP2 terminal input OFF
ON: STP2 terminal input ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Chassis > Brake/EPB > Data List
Tester Display
Stop Light Relay
50003 435 67

c.

With the brake pedal released, check the value of Data List item "Stop Light Relay".

Result:
Result Proceed to
The value of Stop Light Relay is OFF A
The value of Stop Light Relay is ON B



Post-procedure1

a.

Turn the ignition switch off.



A

B

14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A94)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A94-37 (STP2) - Body ground Ignition switch ON 0 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure1

a.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A63,A94)Location & Routing

Click Connector(A63)Instrument Panel>Engine Room Main Wire>Stop Light Switch Assembly

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A63-4 (ACC) or A94-32 (STPO) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

Turn the ignition switch off.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR