Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0484413 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMC Made)  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch (combination switch assembly) turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, the TRC OFF message will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C326774E32
0.281,4.125 2.219,4.458 1.938,0.333 10 false Combination Meter Assembly 0.292,3.958 0.833,4.208 0.542,0.25 10 false H6 0.906,1.76 1.74,2.125 0.833,0.365 10 false CANH 0.917,0.948 1.75,1.313 0.833,0.365 10 false CANL 1.406,0.76 1.729,0.969 0.323,0.208 10 false 25 1.406,1.573 1.729,1.781 0.323,0.208 10 false 9 5.667,0.729 5.99,0.938 0.323,0.208 10 false 43 5.677,1.542 6,1.75 0.323,0.208 10 false 27 5.969,0.948 6.448,1.271 0.479,0.323 10 false CANL 5.969,1.76 6.448,2.083 0.479,0.323 10 false CANH 5.938,2.75 6.417,3.073 0.479,0.323 10 false CSW 5.688,2.75 6.01,2.958 0.323,0.208 10 false 9 3.667,2.76 3.99,2.969 0.323,0.208 10 false 5 3.833,2.781 4.219,2.99 0.385,0.208 10 false E 4.531,2.792 4.854,3 0.323,0.208 10 false + 2.917,4.365 4.896,4.635 1.979,0.271 10 false : CAN Communication Line 3.573,3.438 5.583,3.885 2.01,0.448 10 false VSC OFF Switch (Combination Switch Assembly) 5.521,4.01 7.083,4.729 1.563,0.719 10 false Skid Control ECU (Brake Actuator Assembly) 3.573,3.271 3.896,3.479 0.323,0.208 10 false H18 5.531,3.844 5.854,4.052 0.323,0.208 10 false A94 4.719,2.75 5.042,2.958 0.323,0.208 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION


PROCEDURE

1.READ VALUE USING GTS (TRC (TRAC)/VSC OFF MODE)
a.

Operate the GTS to check the Data List.

Chassis > Brake/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) / TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) / Not defined / VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Chassis > Brake/EPB > Data List
Tester Display
TRC(TRAC)/VSC OFF Mode
50003 435 45

b.

Check that the indicator light and mode condition on the GTS change according to VSC OFF switch (combination switch assembly) operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display (TRC OFF Message) VSC OFF Indicator Light
Not pressed Normal mode (TRC(TRAC) ON/VSC ON) Not displayed Does not come on
Pressing the VSC OFF switch (combination switch assembly) TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) Displayed Does not come on
Pressing and holding the VSC OFF switch (combination switch assembly) VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change. A
Mode condition display is normal, but indicator light does not change. B
Indicator light and mode condition display are normal. C



A

2.INSPECT COMBINATION SWITCH ASSEMBLY

B

C

2.INSPECT COMBINATION SWITCH ASSEMBLY

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH (for Instrument Panel Side)>INSPECTION

OK:

The VSC OFF switch (combination switch assembly) operates normally.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION SWITCH ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H18,A94)Location & Routing

Click Connector(H18)Instrument Panel>Instrument Panel Wire / Speaker Wire>Combination Switch Assembly

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

H18-7 (+) - A94-9 (CSW) Always Below 1 Ω
H18-7 (+) or A94-9 (CSW) - Body ground Always 10 kΩ or higher
H18-5 (E) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR