| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory | DTC Output from | Priority | Note |
|---|---|---|---|---|---|---|---|
| C060B12 | Left Electric Parking Brake Actuator Control Circuit Short to Battery | ·
Diagnosis Condition: Electric parking brake not operating ·
Malfunction Status: The ECU power supply is normal but there is a malfunction in the electric parking brake actuator LH internal circuit (short to +B). ·
Detection Time: Approximately 1 second |
·
Parking brake actuator assembly LH ·
No. 2 parking brake wire assembly ·
Wire harness or connector ·
Parking brake ECU (brake actuator assembly) |
DTC stored | Electric Parking Brake | A | An electric parking brake system malfunction is displayed on the multi-information display. |
To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.
After replacing the parking brake ECU(brake actuator assembly), perform "Calibration".
When replacing the parking brake ECU(brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.
Pre-procedure1
Turn the ignition switch off.
Make sure the No. 2 parking brake wire assembly is securely installed.
Disconnect the u3 parking brake actuator assembly LH connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(u3)Location & Routingewd_type=routing;type=c;code=u3 Click Connector(u3)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>Parking Brake Actuator Assembly LHewd_type=component;type=c;code=u3;pinno=2,1 |
||
| u3-2 (+) - u3-1 (-) | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
for 2WD:Brake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for TMC Made 2WD)>REMOVAL
for AWD:Brake>PARKING BRAKE>ELECTRIC PARKING BRAKE ACTUATOR (for AWD)>REMOVAL
NG
Pre-procedure1
Disconnect the uO2 No. 2 parking brake wire assembly connector.
Procedure1
| *a | Front view of wire harness connector
(to No. 2 Parking Brake Wire Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO2)Location & Routingewd_type=routing;type=w;code=uO2 Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO2;pinno=1,2 |
||
| uO2-1 - uO2-2 | Electric parking brake not operating | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Pre-procedure1
Disconnect the uO2 No. 2 parking brake wire assembly connector.
Disconnect the A95 parking brake ECU (brake actuator assembly) connector.
Procedure1
Measure the voltage according to the value(s) in the table below.
| *a | Front view of wire harness connector | *b | (to Parking Brake ECU (Brake Actuator Assembly)) |
| *c | (to No. 2 Parking Brake Wire Assembly) | - | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(uO2,A95)Location & Routingewd_type=routing;type=w,c;code=uO2,A95 Click Connector(uO2)Body>No. 1 Parking Brake Wire Assembly / No. 2 Parking Brake Wire Assembly>No. 2 Parking Brake Wire Assembly and Floor Wireewd_type=component;type=w;code=uO2;pinno=1,2 Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assemblyewd_type=component;type=c;code=A95;pinno=7,8 |
||
| uO2-1 or A95-7 (MRL+) - Body ground | Always | Below 1 V |
| uO2-2 or A95-8 (MRL-) - Body ground | Always | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMC Made RHD)>REMOVAL
NG