Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model TMC Made RHD) › from 2021.07
RM3700E _54 Brake _093745 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0480812 BRAKE ACTUATOR(for HV Model TMC Made RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model TMC Made RHD)  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C442402N01
1.417,3.083 1.583,2.75 1.583,2.75 1.75,2.75 false 2.979,2.75 3.313,2.75 false 2.708,3.167 3.042,3.167 false 4.385,2.021 4.719,2.021 false 5.479,1.281 5.844,1.281 false 6.438,2.833 6.802,2.833 false 6.635,3.354 6.667,3.583 6.667,3.583 6.833,3.583 false 3.521,4.99 3.552,5.219 3.552,5.219 3.719,5.219 false 4.927,2.49 5.26,2.49 false 1.771,2.615 2.052,2.969 0.281,0.354 18 false 1 2.792,2.635 3.073,2.99 0.281,0.354 18 false 3 2.521,3.031 2.802,3.385 0.281,0.354 18 false 4 4.198,1.896 4.479,2.25 0.281,0.354 18 false 3 6.219,1.146 6.5,1.5 0.281,0.354 18 false 2 6.885,3.448 7.135,3.781 0.25,0.333 18 false 4 6.25,2.688 6.531,3.042 0.281,0.354 18 false 3 3.792,5.146 4.104,5.344 0.313,0.198 10 false *1 5.323,2.365 5.573,2.698 0.25,0.333 18 false 4

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE BOOSTER PUMP ASSEMBLY 47070 - - -
2 BRAKE ACTUATOR ASSEMBLY 44510 (Click here) - -
3 NO. 1 BRAKE ACTUATOR CASE COLLAR 44521A - - -
4 BRAKE ACTUATOR BOLT CUSHION 44546A - - -

*1 BRAKE ACTUATOR BRACKET ASSEMBLY - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)
Brake actuator
1.

Bleed air

2.

Perform "Reset Memory"

3.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Parking Brake ECU (Brake actuator assembly) Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned ON (Click here)

CAUTION:
·
A340386

This vehicle has contains high voltage circuits standardized with orange colored wiring and connectors, so follow the instructions in this manual to perform the procedures correctly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

·

If the correct procedures are not followed according to the instructions in this manual, there is a danger of electric shock from the high voltage circuits.

·
A340358

Be sure to wear insulating gloves when working on high voltage wiring or components.

·

If work is performed without wearing insulating gloves, there is a danger of electric shock.



HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 47070 1.REMOVE BRAKE BOOSTER PUMP ASSEMBLY

Hide 44510 2.REMOVE BRAKE ACTUATOR ASSEMBLY

Z101186

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




a.
C430295


Hide 44521A 3.REMOVE NO. 1 BRAKE ACTUATOR CASE COLLAR

a.
C430297


Hide 44546A 4.REMOVE BRAKE ACTUATOR BOLT CUSHION

a.
C430387