Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for HV Model TMC Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0484414 ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMC Made) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for HV Model TMC Made)  C102014  Ignition Switch On/Start Position Circuit Short to Ground or Open  


DESCRIPTION

When the ignition switch to ON, power is supplied to the parking brake ECU (brake actuator assembly). This DTC is stored if IG power source voltage is not supplied to the parking brake ECU (brake actuator assembly) when communication with other ECUs is established.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C102014 Ignition Switch On/Start Position Circuit Short to Ground or Open
·

Diagnosis Condition:

Ignition switch ON

·

Malfunction Status:

When the hybrid vehicle control ECU is communicating via CAN communication, IG power is not input to the parking brake ECU (brake actuator assembly).

·

Detection Time:

Approximately 15 seconds


·

Wire harness and connector

·

Parking brake ECU (brake actuator assembly)


DTC stored Electric Parking Brake A An electric parking brake system malfunction is displayed on the multi-information display.

WIRING DIAGRAM

C381928E25
1.375,0.948 2.625,1.24 1.25,0.292 10 false ECU-IGR NO. 2 3.26,0.667 3.542,0.979 0.281,0.313 10 false 26 3.521,0.792 3.802,1.104 0.281,0.313 10 false IG 4.531,0.781 5.177,1.031 0.646,0.25 10 false EGND 5.021,0.667 5.302,0.979 0.281,0.313 10 false 2 3.417,2.458 3.813,2.708 0.396,0.25 10 false A95 3.417,2.625 5.073,3.073 1.656,0.448 10 false Parking Brake ECU (Brake Actuator Assembly) 0.75,1.875 2.719,2.271 1.969,0.396 10 false to CAN Communication System 0.958,3.24 2.99,3.552 2.031,0.313 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the parking brake ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMC Made)>UTILITY

·

When replacing the parking brake ECU (brake actuator assembly), operate the electric parking brake switch assembly as the parking brake indicator light blinks when the ignition switch is first turned ON.



PROCEDURE

1.READ VALUE USING GTS (IGR VOLTAGE)
a.

Read the Data List according to the display on the GTS.

Chassis > Electric Parking Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IGR Voltage IG voltage value Min.: 0.0 V
Max.: 25.5 V
Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
Chassis > Electric Parking Brake > Data List
Tester Display
IGR Voltage
50003 485 321
Result:
Result Proceed to
The value of IGR Voltage is between 11 and 14 V A
None of the above conditions are met B




A

2.CLEAR DTC

B

4.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)
2.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Electric Parking Brake > Clear DTCs
50002 485
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check for DTCs.

Chassis > Electric Parking Brake > Trouble Codes
50001 485

Result:
Result Proceed to
C102014 is output A
C102014 is not output B



A

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

B

4.CHECK HARNESS AND CONNECTOR (IG TERMINAL VOLTAGE)

Pre-procedure1

a.

Turn the ignition switch off.


Procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



Pre-procedure2

a.

Disconnect the A95 parking brake ECU (brake actuator assembly) connector.


Procedure2

a.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure3

a.

Turn the ignition switch to ON.


Procedure3

a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A95-26 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

5.CHECK HARNESS AND CONNECTOR (EGND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EGND TERMINAL)

Pre-procedure1

a.

Turn the ignition switch off.


b.

Disconnect the A95 parking brake ECU (brake actuator assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A95)Location & Routing

Click Connector(A95)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

A95-2 (EGND) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

REPLACE PARKING BRAKE ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR