Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM (for Gasoline Model TMC Made) › from 2021.07
RM3700E _54 Brake _093729 PARKING BRAKE _0484415 ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMC Made) C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM(for Gasoline Model TMC Made)  C060962  Electric Parking Brake Switch Signal Compare Failure  


DESCRIPTION

When the electric parking brake switch is pulled, a lock request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from Priority Note
C060962 Electric Parking Brake Switch Signal Compare Failure
·

Parking brake switch open or short circuit is detected for 1 seconds or more

·

Parking brake switch stuck malfunction


·

Electric parking brake switch (electric parking brake switch assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored Brake/EPB A An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status Parking brake switch open circuit is detected ○ - -
Parking brake switch short circuit is detected - ○ -
Parking brake switch stuck malfunction - - ○
Detection Time 1 second or more 1 second or more -
Number of Trips 1 trip 1 trip 1 trip

WIRING DIAGRAM

C367775E80
1.333,3.167 3.75,3.615 2.417,0.448 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 5.167,3.667 6.719,4.083 1.552,0.417 10 false Skid Control ECU (Brake Actuator Assembly) 5.167,3.5 5.604,3.688 0.438,0.188 10 false A94 1.333,3 1.833,3.25 0.5,0.25 10 false H140 3.333,1.25 3.771,1.438 0.438,0.188 10 false SWI1 3.26,1.563 3.792,1.75 0.531,0.188 10 false SWO1 3.323,1.865 3.76,2.052 0.438,0.188 10 false SWI2 3.25,2.427 3.781,2.615 0.531,0.188 10 false SWO2 5.469,1.365 5.906,1.552 0.438,0.188 10 false SWI1 5.458,1.646 5.938,1.833 0.479,0.188 10 false SWO1 5.458,1.969 5.896,2.156 0.438,0.188 10 false SWI2 5.469,2.563 5.979,2.75 0.51,0.188 10 false SWO2 3.802,1.25 3.99,1.448 0.188,0.198 10 false 7 3.802,1.552 4.063,1.75 0.26,0.198 10 false 8 5.198,1.563 5.385,1.76 0.188,0.198 10 false 31 3.802,1.854 3.99,2.052 0.188,0.198 10 false 1 3.802,2.438 3.99,2.635 0.188,0.198 10 false 2 5.188,1.26 5.375,1.458 0.188,0.198 10 false 36 5.198,1.865 5.385,2.063 0.188,0.198 10 false 41 5.188,2.448 5.375,2.646 0.188,0.198 10 false 39

CAUTION / NOTICE / HINT

NOTICE:
·

If the electric parking brake switch is held near the lock position but not fully in the lock position for 1 second or more, a DTC may be stored due to one of the two contacts being ON while the other is OFF. (This is not a system malfunction.)

·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

After replacing the skid control ECU (brake actuator assembly), perform "Calibration".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>CALIBRATION

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

Pre-procedure1

a.

Disconnect the H140 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the A94 skid control ECU (brake actuator assembly) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(A94,H140)Location & Routing

Click Connector(A94)Engine Compartment>Engine Room Main Wire>Brake Actuator Assembly

Click Connector(H140)Instrument Panel>Instrument Panel Wire / Speaker Wire>Electric Parking Brake Switch Assembly

A94-36 (SWI1) - H140-7 (SWI1) Always Below 1 Ω
A94-31 (SWO1) - H140-8 (SWO1) Always Below 1 Ω
A94-41 (SWI2) - H140-1 (SWI2) Always Below 1 Ω
A94-39 (SWO2) - H140-2 (SWO2) Always Below 1 Ω
A94-36 (SWI1) or H140-7 (SWI1) - Body ground Always 10 kΩ or higher
A94-31 (SWO1) or H140-8 (SWO1) - Body ground Always 10 kΩ or higher
A94-41 (SWI2) or H140-1 (SWI2) - Body ground Always 10 kΩ or higher
A94-39 (SWO2) or H140-2 (SWO2) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC

Pre-procedure1

a.

None


Procedure1

a.

Clear the DTCs.

Chassis > Brake/EPB > Clear DTCs
50002 435
Result:
Proceed to
NEXT



Post-procedure1

a.

Turn the ignition switch off.



NEXT

4.CHECK DTC
4.CHECK DTC
a.

Check for DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B