| *A | for TMC Made front Passenger Side | *B | w/ Under Tray |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD.
The following procedure is for LHD.
Use the same procedure for the driver side and front passenger side.
The procedure listed below is for the driver side.
1.INSTALL FRONT SEAT ASSEMBLY
Place the front seat assembly in the cabin as shown in the illustration.
2 or more people are required when reinstalling the front seat assembly into the vehicle.
Protect the front seat leg.
Be careful not to damage the front seat assembly, body exterior or body interior.
for TMC Made:
| *A | for Driver Seat | *B | for Front Passenger Seat |
Disconnect the front seat airbag assembly connector under the front seat assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Connect the connector and engage the clamps.
Insert the 2 location pins of the front seat assembly through the 2 body holes, place the front seat assembly and make sure that the inner and outer seat tracks are locked securely.
Operate the seat track adjusting handle to move the front seat assembly to the rearmost position.
Temporarily install the 2 bolts on the front side of the front seat assembly.
Operate the seat track adjusting handle to move the front seat assembly to the foremost position.
Temporarily install the 2 bolts on the rear side of the front seat assembly.
Operate the seat track adjusting handle to move the front seat assembly to the rearmost position.
Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly in the order shown in the illustration.
Operate the seat track adjusting handle to move the front seat assembly to the foremost position.
Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly in the order shown in the illustration.
for TMMF Made:
Disconnect the front seat airbag assembly connector under the front seat assembly.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Connect the connector and engage the clamps.
Insert the 2 location pins of the front seat assembly through the 2 body holes, place the front seat assembly and make sure that the inner and outer seat tracks are locked securely.
Operate the seat track adjusting handle to move the front seat assembly to the rearmost position.
Temporarily install the 2 bolts on the front side of the front seat assembly.
Operate the seat track adjusting handle to move the front seat assembly to the foremost position.
Temporarily install the 2 bolts on the rear side of the front seat assembly.
Operate the seat track adjusting handle to move the front seat assembly to the rearmost position.
Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly in the order shown in the illustration.
Operate the seat track adjusting handle to move the front seat assembly to the foremost position.
Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly in the order shown in the illustration.
2.INSPECT SEAT SLIDE ADJUSTER LOCK
While performing a sliding operation of the front seat assembly, check that the left and right adjusters move together smoothly and lock simultaneously.
If the seat adjusters do not lock simultaneously, loosen the front seat assembly installation bolts and adjust the adjuster position.
3.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for M15A-FKS:
Click hereGeneral>MAINTENANCE>M15A-FKS AUXILIARY BATTERY>INSTALLATION
for M15A-FXE:
Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>INSTALLATION
71537D
6.INSTALL FRONT SEAT CUSHION PROTECTOR (for TMC Made Front Passenger Side)
71753
7.INSTALL FRONT SEAT UNDER TRAY (w/ Under Tray)
72157A
8.INSTALL SEAT TRACK BRACKET INNER COVER
72137
9.INSTALL SEAT TRACK BRACKET OUTER COVER
72127A
10.INSTALL FRONT SEAT TRACK BRACKET INNER COVER
72123A
11.INSTALL FRONT SEAT TRACK BRACKET OUTER COVER
71910A
12.INSTALL FRONT SEAT HEADREST ASSEMBLY
13. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART