Home › Vehicle Interior › SEAT › LUMBAR SUPPORT ADJUSTER ASSEMBLY › from 2021.07
RM3700E _58 Vehicle Interior _092990 SEAT _0484608 LUMBAR SUPPORT ADJUSTER ASSEMBLY A

SEAT  LUMBAR SUPPORT ADJUSTER ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
B622691N01
6.469,0.229 6.802,0.229 false 3.219,1.708 3.552,1.708 false 2.938,4.208 3.271,4.208 false 4.281,4.698 4.615,4.698 false 5.583,4.271 5.917,4.271 false 5.208,5.063 5.542,5.063 false 6.375,5.26 6.375,4.927 false 0.969,1.5 1.302,1.5 false 6.313,0.063 6.594,0.417 0.281,0.354 18 false 1 3.625,1.573 3.906,1.927 0.281,0.354 18 false 2 5,4.896 5.281,5.25 0.281,0.354 18 false 3 6.302,5.292 6.583,5.646 0.281,0.354 18 false 4 5.99,4.094 6.271,4.448 0.281,0.354 18 false 5 4.063,4.552 4.344,4.906 0.281,0.354 18 false 6 2.74,4.052 3.021,4.406 0.281,0.354 18 false 7 1.375,1.333 1.656,1.688 0.281,0.354 18 false 8

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 FRONT SEAT ASSEMBLY - - - -
3 VERTICAL ADJUSTING HANDLE 72494A - - -
4 RECLINING HINGE COVER 72552B - - -
5 RECLINING ADJUSTER RELEASE HANDLE 72525A - - -
6 SEAT ADJUSTER COVER CAP 71849 - - -
7 FRONT SEAT CUSHION SHIELD 72498A (Click here) - -
8 FRONT SEAT INNER CUSHION SHIELD 71861 - - -

B620228N01
5.76,1 6.094,1 false 5.844,2.802 6.156,3 0.313,0.198 10 false x4 6.167,0.813 6.448,1.167 0.281,0.354 18 false 9

Procedure Part Name Code
Z101186

Z101188

Z101187

9 SEPARATE TYPE FRONT SEATBACK ASSEMBLY - - - -

B621770N01
0.813,2.281 1.229,2.281 false 5.458,0.865 5.458,0.667 false 4.99,0.875 5.74,0.875 5.74,0.875 5.74,0.792 false 4.656,0.719 5.208,1.073 0.552,0.354 18 false 10 0.531,2.125 1.083,2.479 0.552,0.354 18 false 11

Procedure Part Name Code
Z101186

Z101188

Z101187

10 FRONT SEAT HEADREST SUPPORT 71930A - - -
11 SEPARATE TYPE FRONT SEATBACK COVER WITH PAD - (Click here) - -

B620230N02
2.083,3.104 2.083,2.771 false 3.25,3.167 3.25,2.833 false 1.083,3.083 1.083,2.833 false 1.479,3.281 1.479,2.833 1.479,2.833 0.563,2.833 false 0.208,2.688 0.76,3.042 0.552,0.354 18 false 14 1.927,3.125 2.479,3.479 0.552,0.354 18 false 12 3.104,3.188 3.656,3.542 0.552,0.354 18 false 13

Procedure Part Name Code
Z101186

Z101188

Z101187

12 LUMBAR SUPPORT ADJUSTER ASSEMBLY LH 72760D - - -
13 FRONT SEATBACK FELT 79977G - - -
14 FRONT SEATBACK EDGE PROTECTOR 71587 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during lumbar support adjuster assembly LH removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

CAUTION:
B401522

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad, separate type front seatback cover and front seatback pad with cover with the necessary parts in accordance with the extent of the collision damage.


HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system*1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD.

·

The following procedure is for LHD.

·

Lumbar Support Adjuster Assembly is available only on the driver side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B473126

Some of these service operations affect the SRS airbag system. Read precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


Hide 72494A 3.REMOVE VERTICAL ADJUSTING HANDLE

Hide 72552B 4.REMOVE RECLINING HINGE COVER

Hide 72525A 5.REMOVE RECLINING ADJUSTER RELEASE HANDLE

Hide 71849 6.REMOVE SEAT ADJUSTER COVER CAP

Hide 72498A 7.REMOVE FRONT SEAT CUSHION SHIELD

Z101186

Click here(Click here)

Hide 71861 8.REMOVE FRONT SEAT INNER CUSHION SHIELD

Hide 9.REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY

Hide 71930A 10.REMOVE FRONT SEAT HEADREST SUPPORT

Hide 11.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

Z101186

Click here(Click here)

Hide 72760D 12.REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

a.
B622692C01
3.833,0.042 4.052,0.375 0.219,0.333 18 true iii 1.698,0.344 1.896,0.656 0.198,0.313 18 true ii 2.698,0.719 2.896,1.031 0.198,0.313 18 true i 2.802,2.063 3.146,2.365 0.344,0.302 18 false iv
V113147

Remove in this Direction - -


i.

Disengage the clamp.


ii.

Disconnect the connector.


iii.

Disengage the 2 claws to remove the 2 front seatback edge protectors from the front seatback frame sub-assembly.


iv.

Remove the lumbar support adjuster assembly from the front seatback frame sub-assembly as shown in the illustration.



Hide 79977G 13.REMOVE FRONT SEATBACK FELT

a.
B620492


Hide 71587 14.REMOVE FRONT SEATBACK EDGE PROTECTOR