Home › General › MAINTENANCE › M15A-FKS AUXILIARY BATTERY › from 2021.07
RM3700E _V1 General _093024 MAINTENANCE _0442334 M15A-FKS AUXILIARY BATTERY A

MAINTENANCE  M15A-FKS AUXILIARY BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
A478816N01
5.406,0.719 5.74,0.719 false 3.896,0.615 4.229,0.615 false 3.927,1.781 4.26,1.781 false 2.208,2.135 2.521,2.135 false 6.563,0.219 6.875,0.219 false 2.021,1.969 2.302,2.323 0.281,0.354 18 false 4 4.313,1.646 4.594,2 0.281,0.354 18 false 5 4.292,0.469 4.573,0.823 0.281,0.354 18 false 3 5.792,0.573 6.073,0.927 0.281,0.354 18 false 2 6.396,0.073 6.677,0.427 0.281,0.354 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 PRECAUTION - (Click here) - -
2 CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL - - - -
3 CABLE FROM POSITIVE AUXILIARY BATTERY TERMINAL - - - -
4 NO. 2 BATTERY CLAMP SUB-ASSEMBLY 74405 (Click here) - -
5 AUXILIARY BATTERY 28800 - - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during auxiliary battery removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (w/o Advanced Park) (Click here)

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Parking support brake system
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Power back door system Fully close the back door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the back door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When replacing the auxiliary battery, use a new auxiliary battery of the same dimensions and same capacity or more from the same class at a 20-hour rate.



Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

a.
A455696


Hide 3.DISCONNECT CABLE FROM POSITIVE AUXILIARY BATTERY TERMINAL

a.
A455697


Hide 74405 4.REMOVE NO. 2 BATTERY CLAMP SUB-ASSEMBLY

a.
A472809N01
2.917,2.146 3.073,2.344 0.156,0.198 10 true 1 6.667,0.979 6.823,1.177 0.156,0.198 10 true 2 5.521,1.146 5.677,1.344 0.156,0.198 10 true 3 0.167,0.115 0.427,0.427 0.26,0.313 18 true i 2.833,0.333 3.094,0.646 0.26,0.313 18 false ii

i.

Remove the bolt.


ii.

No. 2 battery clamp from the battery clamp sub-assembly in the order shown in the illustration.



Hide 28800 5.REMOVE AUXILIARY BATTERY

a.
A461531