Home › Engine / Hybrid System › M15A-FKS (STARTING) › STARTER (w/ Stop And Start System) › from 2021.07
RM3700E _51 Engine / Hybrid System _093780 M15A-FKS STARTING _0485193 STARTER(w/ Stop And Start System) A

M15A-FKS STARTING  STARTER(w/ Stop And Start System)  REASSEMBLY  


CAUTION / NOTICE / HINT

COMPONENTS (REASSEMBLY)
A495877N01
1.063,4.979 2.146,5.146 1.083,0.167 0.073,2.74 1.156,2.906 1.083,0.167 1.24,0.844 2.323,1.01 1.083,0.167 1.135,0.208 2.219,0.375 1.083,0.167 5.26,1.354 6.344,1.521 1.083,0.167 3.552,5.167 3.385,5.167 3.385,5.167 3.333,5.031 false 2.958,0.875 2.667,0.604 2.667,0.604 2.5,0.604 false 4.885,1.813 5.219,1.813 false 2.063,3.417 1.729,3.417 false 2.656,2.813 2.323,2.813 false 3.104,1.979 2.771,1.979 false 3.698,2.917 3.365,2.917 false 0.927,2.042 0.594,2.042 false 3.104,5.583 2.938,5.583 2.938,5.583 2.771,5.24 false 4.667,4.979 4.5,4.979 4.5,4.979 4.385,4.698 false 6,4.729 5.833,4.729 5.833,4.729 5.719,4.448 false 1.063,5.052 0.896,5.052 0.896,5.052 0.802,5.635 false 2.563,0.302 2.229,0.302 false 5.792,1.021 5.792,1.354 false 1.229,0.927 1.063,0.927 1.063,0.927 0.938,1.135 false 1.333,2.823 1.167,2.823 false 0.427,1.875 0.708,2.229 0.281,0.354 18 false 9 2.313,0.458 2.594,0.813 0.281,0.354 18 false 8 3.396,1.865 3.677,2.219 0.281,0.354 18 false 7 6.302,4.615 6.583,4.969 0.281,0.354 18 false 6 3.396,5.458 3.677,5.813 0.281,0.354 18 false 3 3.854,5.063 4.135,5.417 0.281,0.354 18 false 5 4.938,4.844 5.219,5.198 0.281,0.354 18 false 4 2.719,2.667 3,3.021 0.281,0.354 18 false 2 2.698,0.344 3.01,0.542 0.313,0.198 10 false x2 5.906,0.927 6.219,1.125 0.313,0.198 10 false x2 0.917,5.417 1.229,5.615 0.313,0.198 10 false x3 1.563,3.292 1.844,3.646 0.281,0.354 18 false 1 3.74,2.833 4.052,3.031 0.313,0.198 10 false *2 5.271,1.698 5.583,1.896 0.313,0.198 10 false *1 1.135,4.99 2.26,5.188 1.125,0.198 8 false 6.0 (61, 53 in.*lbf) 1.219,0.208 2.344,0.406 1.125,0.198 8 false 7.5 (76, 66 in.*lbf) 1.292,0.854 2.417,1.052 1.125,0.198 8 false 9.8 (100, 87 in.*lbf) 0.125,2.75 1.25,2.948 1.125,0.198 8 false 9.8 (100, 87 in.*lbf) 5.354,1.354 6.479,1.552 1.125,0.198 8 false 8.3 (85, 73 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY 28021 (Click here) - -
2 RUBBER SEAL - - - -
3 STARTER COMMUTATOR END FRAME ASSEMBLY - (Click here) - -
4 STARTER ARMATURE ASSEMBLY 28160 (Click here) - -
5 STARTER BRUSH HOLDER ASSEMBLY 28140 (Click here) - -
6 STARTER YOKE ASSEMBLY - (Click here) - -
7 MAGNET SWITCH 28226B (Click here) - -
8 STARTER INRUSH CURRENT REDUCTION RELAY 28249 - - -
9 WIRE HARNESS - - - -

*1 STARTER DRIVE HOUSING ASSEMBLY *2 PINION DRIVE LEVER
V100146

N*m (kgf*cm, ft.*lbf): Specified torque
V100135

Hi-temperature Grease

PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A495884C01
5.365,0.552 6.125,0.271 6.125,0.271 6.292,0.271 true 5.583,1.552 5.75,1.552 5.75,1.552 5.948,1.115 true 6.354,0.188 6.667,0.344 0.313,0.156 10 false *a 5.385,1.448 5.698,1.604 0.313,0.156 10 false *b 0.615,0.073 0.896,0.427 0.281,0.354 18 false i 4.323,0.104 4.604,0.458 0.281,0.354 18 false ii
*a Cutout *b Protrusion
V100135

High-temperature Grease - -


i.

Apply high-temperature grease to the pinion drive lever.

HINT:

Apply approximately 0.1 g of high-temperature grease to each section.



ii.

Align the cutout of the starter drive housing assembly with the protrusion of the starter center bearing clutch sub-assembly and install the starter center bearing clutch sub-assembly.



Hide 2.INSTALL RUBBER SEAL

Hide 3.INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY

a.
A495886N01
0.479,0.104 0.76,0.458 0.281,0.354 18 false i

i.

Install the starter commutator end frame assembly to the starter brush holder assembly as shown in the illustration.

HINT:

If the parts are not aligned correctly, the through bolt cannot be attached.




Hide 28160 4.INSTALL STARTER ARMATURE ASSEMBLY

a.
A495887C01
0.49,0.125 0.771,0.479 0.281,0.354 18 false i
V113147

Install in this Direction - -


i.

Spread the brushes on the starter brush holder assembly, and install the starter armature assembly to the starter brush holder assembly.



Hide 28140 5.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A495888C01
3.146,0.552 3.479,0.552 false 2.896,0.969 3.063,0.969 3.063,0.969 3.542,1.458 true 2.875,1.667 3.208,1.667 false 3.813,2.458 4.104,2.646 4.104,2.646 4.271,2.646 false 2.698,1.583 3.01,1.74 0.313,0.156 10 false *1 4.323,2.563 4.635,2.719 0.313,0.156 10 false *2 2.719,0.865 3.031,1.021 0.313,0.156 10 false *3 2.969,0.427 3.281,0.583 0.313,0.156 10 false *a 0.698,0.219 0.979,0.573 0.281,0.354 18 false i
*1 Starter Yoke Assembly *2 Starter Brush Holder Assembly
*3 Starter Armature Assembly - -
*a Hammer - -
V113147

Install in this Direction - -


i.

Install the starter yoke assembly while holding down the starter armature assembly and starter brush holder assembly with the handle of a hammer.



Hide 6.INSTALL STARTER YOKE ASSEMBLY

a.
A498329C01
1.333,0.563 1.521,0.198 1.521,0.198 1.688,0.198 false 1.719,0.594 2.031,1.458 2.031,1.458 2.198,1.458 true 1.75,0.104 2.063,0.26 0.313,0.156 10 false *a 2.292,1.396 2.604,1.552 0.313,0.156 10 false *b 0.552,0.021 0.875,0.438 0.323,0.417 21 false i 4,0.063 4.323,0.479 0.323,0.417 21 false ii
*a Protrusion *b Cutout


i.

Align the cutout of the starter yoke assembly with the protrusion of the starter center bearing clutch sub-assembly.


ii.

Install the starter yoke assembly with the 3 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)



Hide 28226B 7.INSTALL MAGNET SWITCH

a.
A495889C01
0.813,1.135 0.979,1.135 false 0.99,1.052 1.188,1.24 0.198,0.188 10 true *a 0.552,0.073 0.833,0.427 0.281,0.354 18 false i 4.375,0.094 4.656,0.448 0.281,0.354 18 false ii
*a Terminal C - -


i.

Hang the hook of the magnet starter switch assembly on the pinion drive lever.

NOTICE:
·

Connect the magnet starter switch assembly securely to terminal C.

·

Check that the parts are free of foreign matter, oil or grease.




ii.

Install the magnet starter switch assembly with the 2 nuts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)



Hide 28249 8.INSTALL STARTER INRUSH CURRENT REDUCTION RELAY

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

Hide 9.INSTALL WIRE HARNESS

a.
A498331C01
2.469,0.281 2.635,0.281 false 2.563,0.771 2.729,0.771 false 2.385,0.677 2.698,0.833 0.313,0.156 10 false *1 2.323,0.177 2.635,0.333 0.313,0.156 10 false *a
*1 Wire Harness - -
*a Nut - -


Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)