This DTC is output when an open circuit or short occurs in the communication line between a rear side ultrasonic sensor (RLS sensor) and the clearance warning ECU assembly connector or when a malfunction occurs in a rear side ultrasonic sensor (RLS sensor) on the rear.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from | Priority |
|---|---|---|---|---|---|
| C1AF187 | Ultrasonic Sensor (Rear Left Side) Missing Message | Rear side ultrasonic sensor (RLS sensor) lost communication | ·
Rear side ultrasonic sensor (RLS sensor) ·
Harness or connector ·
Clearance warning ECU assembly |
Clearance Warning | A |
Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.
If a DTC is detected again after the repair, turn the ignition switch to ON and turn the TOYOTA parking assist-sensor system on, and then clear the DTC.
Check the vehicle condition and work details.
| Result | Proceed to |
|---|---|
| The clearance warning ECU assembly or ultrasonic sensor has not been replaced | A |
| The clearance warning ECU assembly or ultrasonic sensor has been replaced | B |
A
B
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION
Check that the connector is properly connected to the rear side ultrasonic sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AF187 is output | B |
| None of the above conditions are met | C |
A
B
C
Check that the connector is properly connected to the clearance warning ECU assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AF187 is output | B |
| None of the above conditions are met | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Pre-procedure1
Disconnect the O60 clearance warning ECU assembly connector.
Disconnect the W10 rear side ultrasonic sensor (RLS sensor) connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
Click Location & Routing(O60,W10)Location & Routingewd_type=routing;type=c,c;code=O60,W10 Click Connector(O60)Body>Floor Wire>Clearance Warning ECU Assemblyewd_type=component;type=c;code=O60;pinno=24,22,23 Click Connector(W10)Body>No. 2 Luggage Room Wire>Rear Ultrasonic Sensor Side LHewd_type=component;type=c;code=W10;pinno=4,5,6 |
||
| O60-24 (CDB2) - W10-4 (BI) | Always | Below 1 Ω |
| O60-22 (LIN2) - W10-5 (SI) | Always | Below 1 Ω |
| O60-23 (CSG2) - W10-6 (EI) | Always | Below 1 Ω |
| O60-24 (CDB2) or W10-4 (BI) - Body ground | Always | 10 kΩ or higher |
| O60-22 (LIN2) or W10-5 (SI) - Body ground | Always | 10 kΩ or higher |
| O60-23 (CSG2) or W10-6 (EI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None
OK
NG
Replace the rear side ultrasonic sensor (RLS sensor) with a known good one.
All of the sensors are interchangeable. To confirm whether a sensor is functioning normally, switch it with a known good sensor from the other end of the vehicle.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| C1AF187 is output | B |
| None of the above conditions are met | C |
A
B
C