| *A | w/ Advanced Park | - | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 9 | ULTRASONIC SENSOR CUSHION SET | - | ( )
|
- | - |
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.
1.REMOVE REAR BUMPER ASSEMBLY
89348D
2.REMOVE ULTRASONIC SENSOR CLIP
w/ Advanced park:
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
89342A
3.REMOVE REAR CENTER ULTRASONIC SENSOR
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
89342
4.REMOVE REAR CORNER ULTRASONIC SENSOR
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
89342B
5.REMOVE REAR SIDE ULTRASONIC SENSOR (w/ Advanced Park)
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
89C48B
6.REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER
|
|
|
Heated Area | - | - |
Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Rear Center Ultrasonic Sensor Retainer |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper assembly and rear center ultrasonic sensor retainer excessively.
Remove the rear center ultrasonic sensor retainer.
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
89C48A
7.REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER
|
|
|
Heated Area | - | - |
Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Rear Corner Ultrasonic Sensor Retainer |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper assembly and rear corner ultrasonic sensor retainer excessively.
Remove the rear corner ultrasonic sensor retainer.
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
89C48C
8.REMOVE REAR SIDE ULTRASONIC SENSOR RETAINER (w/ Advanced Park)
|
|
|
Heated Area | - | - |
Heat the rear bumper assembly and rear side ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
| Item | Temperature |
|---|---|
| Rear Bumper Assembly | 40 to 60°C (104 to 140°F) |
| Rear Side Ultrasonic Sensor Retainer |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the rear bumper assembly and rear side ultrasonic sensor retainer excessively.
Remove the rear side ultrasonic sensor retainer.
The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.
9.REMOVE ULTRASONIC SENSOR CUSHION SET
|
|