Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485737 PANORAMIC VIEW MONITOR SYSTEM(w/o Advanced Park) J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/o Advanced Park)  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the Signal Check screen, it is possible to check if the signals sent to the parking assist ECU are normal.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>DIAGNOSIS SYSTEM

HINT:
·

On the Signal Check screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the Signal Check screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Panoramic view monitor switch signal input state DTC is not output Panoramic view monitor switch

WIRING DIAGRAM

E287159E32
2.948,0.406 3.406,0.604 0.458,0.198 10 false D 2.073,0.417 2.531,0.615 0.458,0.198 10 false E 3.271,0.406 3.51,0.583 0.24,0.177 10 false 5 1.833,0.417 2.073,0.594 0.24,0.177 10 false 2 4.833,0.427 5.073,0.604 0.24,0.177 10 false 15 5.146,0.552 5.875,0.75 0.729,0.198 10 false BLSW 5.073,2.302 6.667,2.51 1.594,0.208 10 false Parking Assist ECU 1.729,1.083 4.271,1.604 2.542,0.521 10 false Panoramic View Monitor Switch 1.719,0.896 2.104,1.104 0.385,0.208 10 false H22 5.073,2.125 5.458,2.333 0.385,0.208 10 false O25 0.948,2.25 2.99,2.448 2.042,0.198 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the radio and display receiver assembly after the auxiliary battery cable is disconnected, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>CALIBRATION



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E409396

Check which items display on the signal check screen.


Result:
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN" displays "CHK" (red) B



A

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)
a.

Disconnect the H22 panoramic view monitor switch connector.


b.

Disconnect the O25 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(H22,O25)Location & Routing

Click Connector(H22)Instrument Panel>Instrument Panel Wire / Speaker Wire>Panoramic View Monitor Switch

Click Connector(O25)Body>Floor Wire>Parking Assist ECU

H22-5 (D) - O25-15 (BLSW) Always Below 1 Ω
H22-2 (E) - Body ground Always Below 1 Ω
H22-5 (D) or O25-15 (BLSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PANORAMIC VIEW MONITOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR