Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485736 PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park) D

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park)  CALIBRATION  


ADJUST PANORAMIC VIEW MONITOR SYSTEM


a.

This panoramic view monitor system can be set from the diagnostic screen of the multi-display assembly.


b.

If the following operations are performed, it is necessary to perform adjustments and checks on the diagnostic screen.


c.

Conduct the pre-work checks (Procedure 1) before performing screen adjustment.

Part Name Operation Adjustment Item Proceed to

*1: At the time of SST (marker tool set) non-use

*2: At the time of use SST (marker tool set)

Parking assist ECU Replacement Parking assist ECU initialization Procedure 2
Procedure 11*1
Procedure 12*2
Procedure 13
Procedure 14
Adjust steering angle Procedure 15
Suspension, tires, etc. The vehicle height changes because of suspension or tire replacement Parking assist ECU initialization Procedure 2
Procedure 11*1
Procedure 12*2
Procedure 13
Procedure 14
Adjust steering angle Procedure 15
Rear television camera assembly
·

Replacement

·

Installation angle of the rear television camera changes because of the removal and installation of the rear television camera, etc.


Rear television camera view adjustment Procedure 2
Procedure 5*1
Procedure 12*2
Procedure 6
Procedure 14
·

Front television camera assembly

·

Front bumper assembly

·

Radiator grille assembly


·

Replacement

·

Installation angle of the front television camera changes because of the removal and installation of the front television camera, etc.


Front television camera view adjustment Procedure 2
Procedure 3*1
Procedure 12*2
Procedure 4
Procedure 14
·

Side television camera assembly LH

·

Outer rear view mirror assembly LH


·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 7*1
Procedure 12*2
Procedure 8
Procedure 14
Procedure 16
·

Side television camera assembly RH

·

Outer rear view mirror assembly RH


·

Replacement

·

Installation angle of the side television camera changes because of the removal and installation of the side television camera, etc.


Side television camera view adjustment Procedure 2
Procedure 9*1
Procedure 12*2
Procedure 10
Procedure 14
Procedure 16
·

Front television camera assembly, radiator grille assembly or front bumper assembly

·

Rear television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Replacement or removal and installation of 2 or more parts Television camera view adjustment Procedure 2
Procedure 11*1
Procedure 12*2
Procedure 13
Procedure 14
Procedure 16



PROCEDURE 1: PRE-WORK CHECKS


a.

Preliminary checks

NOTICE:
·

Provide shadow to prevent backlight from hitting the camera.

·

Use string that does not stretch.

·

Apply pieces of adhesive tape to serve as check markers. When placing the markers, make them 100 mm (3.94 in.) wide.

·

SST may also be used for the recognition markers and the positioning and check markers used in optical axis adjustment.



i.

Perform the work in a wide, level location (L direction approximately 6.5 m x W direction approximately 3.5 m).


ii.

Park the vehicle on a flat surface with the steering wheel centered.

NOTICE:

Before stopping the vehicle, move the vehicle backward and forward to ensure that both the steering wheel and the tires point straight ahead.



iii.

Adjust the tire pressure to the specified value(s).


iv.

Remove all luggage from the vehicle and place the markers before starting work.



b.

Marker locations (check marker)

i.

Secure the string to the locations required to make the checks and set markers as shown in the illustration.

·
E287135C01
0.479,0.698 0.844,1.146 false 2.229,0.469 1.844,1.115 false 2.302,1.333 2.552,1.708 false 1.104,1.333 0.854,1.74 false 2.01,4.052 1.708,3.688 false 2.573,3.49 2.271,3.083 false 0.292,0.583 0.75,0.781 0.458,0.198 10 false *e 2.302,0.396 3.188,0.677 0.885,0.281 10 false *b 0.729,1.76 0.948,2 0.219,0.24 10 false *a 2.063,4 2.521,4.198 0.458,0.198 10 false *d 2.615,3.5 3.073,3.698 0.458,0.198 10 false *c 2.531,1.75 2.75,1.99 0.219,0.24 10 false *a
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3


Front camera adjustment only

·
E287136C01
1.719,1.042 2.073,0.563 false 2.552,3.135 2.781,2.729 false 2.375,3.823 2.5,4.01 false 0.958,3.823 0.708,4.094 false 1.521,3.813 1.521,4.292 false 0.552,3.49 0.76,3.792 false 2.146,0.469 2.604,0.667 0.458,0.198 10 false *d 0.385,3.406 0.844,3.604 0.458,0.198 10 false *e 0.563,4.094 1.25,4.458 0.688,0.365 10 false *a 2.458,4.042 3.146,4.406 0.688,0.365 10 false *a 1.427,4.344 2.365,4.552 0.938,0.208 10 false *b 2.823,2.635 3.323,2.854 0.5,0.219 10 false *c
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 4


Rear camera adjustment only

·
E287137C01
1.063,0.917 0.688,0.563 false 2.281,0.958 2.688,0.656 false 2.271,2.906 2.625,2.646 false 2.375,3.521 2.688,3.313 false 1.719,3.635 1.927,3.875 false 1.125,3.542 1.49,4.125 false 1.094,3.833 0.844,4.083 false 1.073,1.542 0.771,1.365 false 1.052,2.25 0.781,2.375 false 0.531,0.458 1.24,0.833 0.708,0.375 10 false *a 1.469,4.167 1.698,4.406 0.229,0.24 10 false *a 0.594,1.281 0.969,1.573 0.375,0.292 10 false *b 0.708,4.083 1.156,4.333 0.448,0.25 10 false *g 1.958,3.844 2.406,4.094 0.448,0.25 10 false *d 2.667,2.563 3.115,2.813 0.448,0.25 10 false *c 2.74,3.24 3.188,3.49 0.448,0.25 10 false *f 2.719,0.583 3.167,0.833 0.448,0.25 10 false *e 0.604,2.323 0.979,2.615 0.375,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 5


Left camera adjustment only

·
E287138C01
0.573,0.438 0.854,0.906 false 2.615,0.563 2.344,0.854 false 2.594,3.781 2.313,3.74 false 2.271,3.521 1.844,4.188 false 1.708,3.615 1.365,3.844 false 0.969,3.479 0.75,3.229 false 0.885,2.865 0.667,2.615 false 2.615,1.188 2.344,1.479 false 2.677,2.427 2.344,2.167 false 2.646,0.5 3.344,0.844 0.698,0.344 10 false *a 1.74,4.188 2.104,4.448 0.365,0.26 10 false *a 2.635,1.094 2.979,1.385 0.344,0.292 10 false *b 0.406,0.323 0.792,0.542 0.385,0.219 10 false *e 0.51,2.49 0.896,2.708 0.385,0.219 10 false *c 0.594,3.125 0.979,3.344 0.385,0.219 10 false *f 1.188,3.792 1.573,4.01 0.385,0.219 10 false *d 2.635,3.729 3.021,3.948 0.385,0.219 10 false *g 2.708,2.427 3.052,2.719 0.344,0.292 10 false *b
*a Cross Check Marker
*b Check Marker
*c String 1
*d String 2
*e String 3
*f String 4
*g String 6


Right camera adjustment only

·

Adjustment of 4 cameras

E287104C01
4.833,3.344 5.083,3 false 2.417,1.5 2.875,1.5 false 4.26,1.5 4.75,1.5 false 3.25,4.469 3.573,4.135 false 3.917,4.469 3.792,4.073 false 5,4.031 5.25,4.344 false 5,1.115 5.25,0.833 false 4.292,1.073 5,0.417 false 2.823,1.083 2.406,0.667 false 3.667,1.083 3.844,0.76 false 4.302,1.771 4.823,1.771 false 4.302,2.552 4.823,2.552 false 4.292,4.094 4.542,4.406 false 2.5,4.417 2.823,4.083 false 2.313,1.792 2.833,1.792 false 2.313,2.552 2.833,2.552 false 2.219,0.521 2.51,0.75 0.292,0.229 10 false *a 5.052,0.333 6.302,0.5 1.25,0.167 10 false *a 4.875,1.698 5.708,1.865 0.833,0.167 10 false *b 3.865,4.5 4.115,4.719 0.25,0.219 10 false *b 3.854,0.646 4.083,0.896 0.229,0.25 10 false *b 2.25,1.438 2.667,1.604 0.417,0.167 10 false *g 4.802,1.417 5.219,1.583 0.417,0.167 10 false *h 5.135,2.917 5.552,3.083 0.417,0.167 10 false *c 5.302,0.75 5.719,0.917 0.417,0.167 10 false *e 5.229,4.385 5.646,4.552 0.417,0.167 10 false *f 3.063,4.5 3.479,4.667 0.417,0.167 10 false *d 4.865,2.479 5.698,2.646 0.833,0.167 10 false *b 4.531,4.448 4.948,4.615 0.417,0.167 10 false *a 2.365,4.406 2.781,4.573 0.417,0.167 10 false *a 2.125,1.719 2.958,1.885 0.833,0.167 10 false *b 2.125,2.458 2.958,2.625 0.833,0.167 10 false *b
*a Cross Check Marker *b Check Marker
*c String 1 *d String 2
*e String 3 *f String 4
*g String 5 *h String 6





c.

Marker positions

i.

Set the check markers at the positions shown in the illustration.

E287105C01
1.594,2.135 1.594,1.938 1.594,1.938 1.927,1.938 false 1.594,4.073 1.594,3.875 1.594,3.875 1.927,3.875 false 3.76,0.5 3.76,0.198 3.76,0.198 4.094,0.198 false 4.927,3.281 4.927,3.125 4.927,3.125 4.646,3.125 false 3.385,0.5 3.385,0.198 3.385,0.198 3.073,0.198 false 5.5,3.073 5.5,2.917 5.5,2.917 5.219,2.917 false 6.073,2.75 6.073,2.594 6.073,2.594 5.792,2.594 false 6.656,2.531 6.656,2.375 6.656,2.375 6.375,2.375 false 3.313,5.094 3.406,4.99 false 3.167,5.458 3.24,5.333 false 3.802,5.104 3.729,4.99 false 4,5.469 3.927,5.333 false 1.51,2.167 1.823,2.365 0.313,0.198 10 false *a 1.531,4.104 1.844,4.302 0.313,0.198 10 false *b 3.073,5.479 3.385,5.677 0.313,0.198 10 false *c 3.938,5.479 4.25,5.677 0.313,0.198 10 false *c 4.865,3.302 5.177,3.5 0.313,0.198 10 false *e 6,2.76 6.313,2.958 0.313,0.198 10 false *g 6.583,2.573 6.896,2.771 0.313,0.198 10 false *h 4.135,0.125 4.448,0.323 0.313,0.198 10 false *d 3.208,5.125 3.521,5.323 0.313,0.198 10 false *d 2.885,0.135 3.198,0.333 0.313,0.198 10 false *d 3.74,5.125 4.052,5.323 0.313,0.198 10 false *d 5.438,3.115 5.75,3.313 0.313,0.198 10 false *f
*a 3700 mm (12.14 ft.) *b 1400 mm (4.59 ft.)
*c 1200 mm (3.94 ft.) *d 693 mm (2.27 ft.)
*e 1000 mm (3.28 ft.) *f 1200 mm (3.94 ft.)
*g 2200 mm (7.22 ft.) *h 2400 mm (7.87 ft.)




d.

Marker locations (SST)

SST
09870-52010  09870-52020  

i.

Secure the strings to the location required to make the checks and set SST as shown in the illustration.

·
E439704C01
0.719,1.729 0.375,1.24 false 2.156,4.5 1.729,4.083 false 2.854,3.906 2.427,3.49 false 2.219,0.177 2.531,0.333 0.313,0.156 10 false *a 2.917,3.854 3.229,4.01 0.313,0.156 10 false *b 2.219,4.438 2.531,4.594 0.313,0.156 10 false *c 0.198,1.146 0.51,1.302 0.313,0.156 10 false *d 3.115,2.469 3.427,2.625 0.313,0.156 10 false *a 0.156,2.51 0.469,2.667 0.313,0.156 10 false *a
*a SST (Except Side Setting)
*b String 1
*c String 2
*d String 3


Front camera adjustment only

·
E439705C01
0.281,3.385 0.698,2.969 false 1.719,0.51 2.135,0.302 false 0.365,2.615 0.563,2.438 false 0.167,1.365 0.479,1.521 0.313,0.156 10 false *a 0.177,2.563 0.49,2.719 0.313,0.156 10 false *b 2.208,0.229 2.521,0.385 0.313,0.156 10 false *c 0.094,3.333 0.406,3.49 0.313,0.156 10 false *d 3.083,1.344 3.396,1.5 0.313,0.156 10 false *a 2.219,3.229 2.531,3.385 0.313,0.156 10 false *a
*a SST (Except Side Setting)
*b String 1
*c String 2
*d String 4


Rear camera adjustment only

·
E439706C01
3.021,3.167 2.875,2.917 false 2.969,3.698 2.823,3.448 false 2.542,0.469 2.208,0.865 false 1.917,4.385 1.677,4.125 false 3.083,0.875 2.813,1.208 false 0.24,0.229 0.552,0.385 0.313,0.156 10 false *a 0.219,1.792 0.531,1.948 0.313,0.156 10 false *b 3.031,3.208 3.344,3.365 0.313,0.156 10 false *c 2.594,0.396 2.906,0.552 0.313,0.156 10 false *d 3.115,0.792 3.427,0.948 0.313,0.156 10 false *e 3,3.75 3.313,3.906 0.313,0.156 10 false *f 1.979,4.354 2.292,4.51 0.313,0.156 10 false *g 0.198,3.625 0.51,3.781 0.313,0.156 10 false *a
*a SST (Except Side Setting)
*b SST (Side Setting)
*c String 1
*d String 2
*e String 3
*f String 4
*g String 5


Left camera adjustment only

NOTICE:

The vertical direction of SST (television camera adjustment target) differs depending on whether side setting or front, rear and corner setting is used.


·
E439707C01
2.51,3.219 2.208,2.927 false 0.406,3.708 0.604,3.448 false 1.083,0.771 1.385,0.417 false 0.49,0.938 0.792,1.208 false 1.406,4.385 1.625,4.115 false 2.906,0.198 3.219,0.354 0.313,0.156 10 false *a 2.906,1.802 3.219,1.958 0.313,0.156 10 false *b 2.563,3.208 2.875,3.365 0.313,0.156 10 false *c 1.438,0.344 1.75,0.5 0.313,0.156 10 false *d 0.302,0.823 0.615,0.979 0.313,0.156 10 false *e 0.24,3.688 0.552,3.844 0.313,0.156 10 false *f 1.208,4.333 1.521,4.49 0.313,0.156 10 false *g 2.927,3.583 3.24,3.74 0.313,0.156 10 false *a
*a SST (Except Side Setting)
*b SST (Side Setting)
*c String 1
*d String 2
*e String 3
*f String 4
*g String 6


Right camera adjustment only

NOTICE:

The vertical direction of SST (television camera adjustment target) differs depending on whether side setting or front, rear and corner setting is used.


·

Adjustment of 4 cameras

NOTICE:

The vertical direction of SST differs depending on whether side setting or front, rear and corner setting is used.


E439708C01
4.927,3.635 5.313,3.219 false 3.135,5.635 3.521,5.219 false 1.385,1.052 1.833,1.448 false 1.375,4.729 1.76,4.313 false 2.365,0.594 2.813,0.99 false 3.802,5.594 4.188,5.177 false 5.271,2.198 5.583,2.354 0.313,0.156 10 false *b 5.396,3.125 5.708,3.281 0.313,0.156 10 false *c 2.938,5.573 3.25,5.729 0.313,0.156 10 false *d 1.167,0.979 1.479,1.135 0.313,0.156 10 false *e 1.198,4.729 1.51,4.885 0.313,0.156 10 false *f 2.167,0.49 2.479,0.646 0.313,0.156 10 false *g 3.625,5.573 3.938,5.729 0.313,0.156 10 false *h 0.531,3.5 0.844,3.656 0.313,0.156 10 false *a 4.74,4.615 5.052,4.771 0.313,0.156 10 false *a 6.208,3.479 6.521,3.635 0.313,0.156 10 false *a 6.25,1.583 6.563,1.74 0.313,0.156 10 false *a 4.74,0.115 5.052,0.271 0.313,0.156 10 false *a 0.542,1.552 0.854,1.708 0.313,0.156 10 false *a 1.563,2.208 1.875,2.365 0.313,0.156 10 false *b
*a SST (Except Side Setting) *b SST (Side Setting)
*c String 1 *d String 2
*e String 3 *f String 4
*g String 5 *h String 6





e.

Marker positions

SST
09870-52010  09870-52020  

i.

Set SST in the positions shown in the illustration.

NOTICE:

The vertical direction of SST (television camera adjustment target) differs depending on whether side setting or front, rear and corner setting is used.


E439709C02
3.208,1.323 3.365,1.177 false 4.177,1.313 4.042,1.177 false 3.26,4.979 3.417,4.833 false 4.198,4.969 4.063,4.833 false 1.427,3.333 1.74,3.49 0.313,0.156 10 false *b 2.281,3.333 2.594,3.49 0.313,0.156 10 false *c 0.375,3.323 0.688,3.479 0.313,0.156 10 false *a 0.354,4.583 0.667,4.74 0.313,0.156 10 false *d 1.417,4.594 1.729,4.75 0.313,0.156 10 false *e 3.156,6.427 3.469,6.583 0.313,0.156 10 false *f 4.01,6.427 4.323,6.583 0.313,0.156 10 false *f 4.969,3.354 5.281,3.51 0.313,0.156 10 false *c 3.063,4.917 3.375,5.073 0.313,0.156 10 false *g 4.25,4.917 4.563,5.073 0.313,0.156 10 false *g 3.021,1.323 3.333,1.479 0.313,0.156 10 false *g 4.229,1.323 4.542,1.479 0.313,0.156 10 false *g
*a 6350 mm (20.83 ft.) *b 3750 mm (12.3 ft.)
*c 2200 mm (7.22 ft.) *d 2650 mm (8.69 ft.)
*e 1450 mm (4.76 ft.) *f 1250 mm (4.1 ft.)
*g 1450 mm (4.76 ft.) - -





PROCEDURE 2: SET DATUM POINTS


a.

Extend the datum line (string 1).

i.
E444506C01
1.021,2.781 1.51,3.135 true 0.969,3.188 1.521,3.271 true 0.771,3.104 1.083,3.26 0.313,0.156 10 false *a 0.823,2.677 1.135,2.833 0.313,0.156 10 false *b
*a Mark A
*b Weight


Hang a weight with a pointed tip and accurately mark the center position on the road surface. (Mark A)

NOTICE:

Make sure that the weight hangs straight down from the string.



ii.

Repeat the procedure to mark the right side. (Mark B)


iii.
E287139C01
1.01,2.771 1.292,2.458 false 2.417,2.74 2.125,2.458 false 2.385,2.458 2.542,2.073 false 2.594,1.969 2.875,2.135 0.281,0.167 10 false *a 0.885,2.802 1.135,2.938 0.25,0.135 10 false *b 2.385,2.792 2.646,2.969 0.26,0.177 10 false *c
*a String 1
*b Mark A
*c Mark B


Secure string 1 so that it passes through marks A and B on the left and right sides.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.




b.

Extend the vehicle center line (string 2).

i.

Hang a weight with a pointed tip such that is passes through the center of the front television camera assembly and accurately mark the center position on the road surface. (Mark C)

E444507C01
3.51,2.177 3.865,2.25 true 3.917,2.365 4.396,2.438 true 1.063,0.177 1.646,0.823 true 2.271,0.24 1.656,0.688 true 2.344,2.531 1.698,1.427 true 0.854,0.115 1.167,0.271 0.313,0.156 10 false *a 3.333,2.115 3.646,2.271 0.313,0.156 10 false *b 2.344,0.146 2.594,0.354 0.25,0.208 10 false *c 4.469,2.385 4.781,2.542 0.313,0.156 10 false *d 2.438,2.5 2.75,2.656 0.313,0.156 10 false *1
*1 Front Television Camera Assembly - -
*a Center Point *b Weight
*c String *d Mark C



ii.

Hang a weight with a pointed tip from the center of the rear emblem and accurately mark the center position on the road surface. (Mark D)

E444508C01
2.552,2.313 3.094,2.531 true 5.51,2.01 6.427,2.552 true 5.521,2.177 4.854,2.594 true 3.094,2.177 2.531,2.229 true 4.656,2.521 4.969,2.677 0.313,0.156 10 false *a 3.146,2.125 3.458,2.281 0.313,0.156 10 false *b 6.49,2.51 6.802,2.667 0.313,0.156 10 false *c 3.156,2.479 3.469,2.635 0.313,0.156 10 false *d 5.208,0.531 5.417,0.729 0.208,0.198 10 true *e 5.688,0.542 5.896,0.74 0.208,0.198 10 true *e
*a Center *b Weight
*c String *d Mark D
*e Equal Distance to Center - -



iii.
E287140C01
1.719,1.333 2.229,0.896 false 2.219,2.927 2.583,2.427 false 1,2.188 1.708,2.917 false 1.719,3.208 2.104,3.573 false 1.375,3.969 1.719,3.656 false 0.802,2.083 1.021,2.281 0.219,0.198 10 false *a 2.271,0.781 2.458,0.958 0.188,0.177 10 false *d 2.156,3.542 2.385,3.729 0.229,0.188 10 false *e 2.625,2.313 2.875,2.51 0.25,0.198 10 false *b 1.24,3.979 1.427,4.177 0.188,0.198 10 false *c
*a Datum Point
*b String 1
*c String 2
*d Mark C
*e Mark D


Secure string 2 so that it passes through marks C and D at the front and rear of the vehicle.

NOTICE:

When securing string, check that there is no slack and the string is not twisted.


HINT:

Set the point where strings 1 and 2 intersect as the datum point.





PROCEDURE 3: SET MARKERS (FRONT ADJUSTMENT)


a.
E287141C01
1.719,1.208 2.24,0.76 false 2.594,3.448 2.333,3.156 false 2.01,4.104 1.708,3.76 false 1.125,3.781 1.323,3.781 1.323,3.781 1.719,3.156 false 0.583,1.917 0.771,1.74 0.771,1.74 0.99,1.74 false 1.031,1.667 1.281,1.865 0.25,0.198 10 false *a 2.302,0.677 2.583,0.875 0.281,0.198 10 false *e 2.635,3.479 2.865,3.656 0.229,0.177 10 false *c 2.063,4.125 2.281,4.292 0.219,0.167 10 false *d 0.958,3.708 1.208,3.885 0.25,0.177 10 false *b
*a 3700 mm (12.14 ft.)
*b Datum Point
*c String 1
*d String 2
*e Mark E


In front of the vehicle, extend string (3) perpendicular to the vehicle center line (string (2)), and place a marker.

i.

Mark the position on string 2 in front of the vehicle, 3700 mm (12.14 ft.) from the datum point. (Mark E)


ii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



iv.
E287142C03
0.771,0.927 1.094,1.25 false 1.115,1.656 1.396,1.25 false 2.281,1.688 2.042,1.25 false 2.688,1.438 2.313,1.25 false 2.688,0.573 2.583,0.573 2.583,0.573 2.458,1.25 false 2.042,4.073 1.719,3.76 false 1.938,0.938 2.094,0.448 2.094,0.448 2.25,0.448 false 1.417,0.938 1.26,0.51 1.26,0.51 1.104,0.51 false 0.917,0.417 1.115,0.583 0.198,0.167 10 false *a 0.594,0.823 0.802,1.01 0.208,0.188 10 false *f 0.927,1.635 1.156,1.792 0.229,0.156 10 false *d 2.333,1.688 2.51,1.833 0.177,0.146 10 false *e 2.74,1.427 2.979,1.583 0.24,0.156 10 false *g 2.74,0.5 2.948,0.656 0.208,0.156 10 false *c 2.083,4.073 2.292,4.24 0.208,0.167 10 false *b 2.292,0.354 2.521,0.51 0.229,0.156 10 false *a
*a 1200 mm (3.94 ft.)
*b String 2
*c String 3
*d Mark F
*e Mark G
*f Mark H
*g Mark I


Secure string (3) so that it passes through marks F and G as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string (3), 1200 mm (3.94 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I).


vi.
E287109C03
0.75,1.667 1.063,1.25 false 2.333,1.667 1.917,1.125 false 1.083,1.083 0.833,0.833 false 2.052,1.083 1.833,0.333 false 1.385,1.083 1.167,0.5 false 2.323,0.635 2.323,0.333 2.323,0.333 2.583,0.333 false 2.333,1.083 2.667,0.75 2.667,0.75 2.833,0.75 false 3.25,1.333 3.25,1.104 3.25,1.104 3.052,1.104 false 2.781,1.708 2.365,1.229 false 2.698,2.927 2.438,3.135 false 0.604,1.688 0.823,1.875 0.219,0.188 10 false *c 2.313,1.708 2.552,1.875 0.24,0.167 10 false *d 0.667,0.667 0.896,0.865 0.229,0.198 10 false *h 1.073,0.333 1.365,0.531 0.292,0.198 10 false *f 1.729,0.135 2.031,0.365 0.302,0.229 10 false *g 2.885,0.667 3.063,0.813 0.177,0.146 10 false *i 2.635,0.25 2.865,0.417 0.229,0.167 10 false *a 3.188,1.375 3.417,1.604 0.229,0.229 10 false *b 2.771,1.729 3.031,1.958 0.26,0.229 10 false *c 2.729,2.823 2.969,2.99 0.24,0.167 10 false *e
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c Cross Check Marker
*d Check Marker
*e String 1
*f Mark F
*g Mark G
*h Mark H
*i Mark I


Place and secure the cross check markers, centered on marks H and I.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.




vii.

Place the check marker between marks F and G.


viii.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 4: SET SST (FRONT ADJUSTMENT)


a.
E439842C01
1.188,2.365 1.385,2.552 false 0.594,2.219 0.802,2.094 false 1.583,3.615 2.094,3.188 true 2.135,1.229 2.375,1.354 false 2.135,0.896 2.396,0.781 false 2.104,3.823 2.427,4.042 false 2.729,3.167 2.938,3.406 false 1.448,2.531 1.76,2.688 0.313,0.156 10 false *a 0.417,2.177 0.729,2.333 0.313,0.156 10 false *b 1.365,3.563 1.677,3.719 0.313,0.156 10 false *c 3,3.406 3.313,3.563 0.313,0.156 10 false *d 2.49,3.99 2.802,4.146 0.313,0.156 10 false *e 2.438,1.313 2.75,1.469 0.313,0.156 10 false *f 2.458,0.719 2.771,0.875 0.313,0.156 10 false *g
*a 3750 mm (12.3 ft.)
*b 6350 mm (20.83 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark W


In front of the vehicle, extend string (3) perpendicular to the vehicle center line (string (2)), and place SST.

SST
09870-52010  09870-52020  

i.

Mark the position on string (2) in front of the vehicle, 3750 mm (12.3 ft.) from the datum point. (Mark E)


ii.

Mark the position on string (2) in front of the vehicle, 6350 mm (20.83 ft.) from the datum point. (Mark W)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287142C03
0.771,0.927 1.094,1.25 false 1.115,1.656 1.396,1.25 false 2.281,1.688 2.042,1.25 false 2.688,1.438 2.313,1.25 false 2.688,0.573 2.583,0.573 2.583,0.573 2.458,1.25 false 2.042,4.073 1.719,3.76 false 1.938,0.938 2.094,0.448 2.094,0.448 2.25,0.448 false 1.417,0.938 1.26,0.51 1.26,0.51 1.104,0.51 false 0.917,0.417 1.115,0.583 0.198,0.167 10 false *a 0.594,0.823 0.802,1.01 0.208,0.188 10 false *f 0.927,1.635 1.156,1.792 0.229,0.156 10 false *d 2.333,1.688 2.51,1.833 0.177,0.146 10 false *e 2.74,1.427 2.979,1.583 0.24,0.156 10 false *g 2.74,0.5 2.948,0.656 0.208,0.156 10 false *c 2.083,4.073 2.292,4.24 0.208,0.167 10 false *b 2.292,0.354 2.521,0.51 0.229,0.156 10 false *a
*a 1250 mm (4.1 ft.)
*b String 2
*c String 3
*d Mark F
*e Mark G
*f Mark AA
*g Mark AB


Secure string (3) so that it passes through marks F and G as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



vi.

Mark positions on string (3), 1250 mm (4.1 ft.) to the left and right of the vehicle center line (string (2)). (Marks AA and AB).


vii.
E439704C02
0.802,1.375 1.167,1.75 false 1.698,1.354 1.448,1.104 false 2.99,1.333 2.76,1.208 true 2.073,1.563 2.24,1.75 false 2.948,0.281 2.771,0.396 false 2.031,4.292 1.719,4.094 false 0.667,1.729 0.427,1.521 false 2.656,0.51 2.406,0.292 false 2.438,1.229 2.323,1.354 false 1.26,0.979 1.479,1.167 0.219,0.188 10 false *i 3.042,1.302 3.24,1.458 0.198,0.156 10 false *d 0.604,1.25 0.823,1.427 0.219,0.177 10 false *g 2.094,4.25 2.333,4.417 0.24,0.167 10 false *e 0.229,1.396 0.469,1.542 0.24,0.146 10 false *f 1.854,1.427 2.031,1.573 0.177,0.146 10 false *h 3.094,2.49 3.323,2.656 0.229,0.167 10 false *a 3.01,0.188 3.229,0.375 0.219,0.188 10 false *c 0.167,2.479 0.396,2.646 0.229,0.167 10 false *a 2.198,1.344 2.427,1.51 0.229,0.167 10 false *a 2.208,0.177 2.427,0.344 0.219,0.167 10 false *b
*a SST (Television Camera Adjustment Target)
*b SST (L Type Stand)
*c SST (Television Camera Adjustment Target) Center Line
*d SST (L Type Stand) Center Line
*e String 2
*f String 3
*g Mark AA
*h Mark AB
*i Mark W


While the center line of SST (television camera adjustment target) is aligned with mark W, place string (2) so that it overlaps the center line of SST (L type stand) as shown in the illustration.


viii.

Align the center line of SST (television camera adjustment target) with marks AA and AB and place it parallel with string (3) as shown in the illustration.


ix.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 5: SET MARKERS (REAR ADJUSTMENT)


a.

To the rear of the vehicle, extend string (4) perpendicular to the vehicle center line (string (2)), and place a check marker.

i.
E287143C01
1.719,1.104 2.208,0.854 false 0.948,2.26 1.167,2.26 1.167,2.26 1.719,2.844 false 1.229,4.021 1.688,3.573 false 0.698,3.104 0.896,3.104 0.896,3.104 1.094,3.271 false 2.74,3.24 2.552,2.833 false 0.531,3.031 1.604,3.229 1.073,0.198 10 false *a 1.063,3.99 1.542,4.25 0.479,0.26 10 false *e 0.792,2.198 1.615,2.458 0.823,0.26 10 false *b 2.271,0.802 3.094,1.063 0.823,0.26 10 false *d 2.75,3.26 3.229,3.521 0.479,0.26 10 false *c
*a 1400 mm (4.59 ft.)
*b Datum Point
*c String 1
*d String 2
*e Mark J


Mark a position on string 2 to the rear of the vehicle, 1400 mm (4.59 ft.) from the datum point. (Mark J)


ii.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


iii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



iv.
E287144C03
1.708,0.896 2.208,0.542 false 1,3.052 1.396,3.354 false 0.677,3.802 1.094,3.354 false 2.385,3.042 2.073,3.344 false 2.875,3.646 2.677,3.344 false 2.615,3.802 2.313,3.344 false 2.167,3.969 1.969,3.667 false 1.188,3.979 1.417,3.667 false 2.292,0.49 2.75,0.688 0.458,0.198 10 false *b 0.823,2.938 1.281,3.135 0.458,0.198 10 false *e 2.438,2.969 2.896,3.167 0.458,0.198 10 false *d 2.844,3.698 3.302,3.896 0.458,0.198 10 false *c 2.542,3.854 3,4.052 0.458,0.198 10 false *g 2.167,4.042 3.104,4.26 0.938,0.219 10 false *a 1.115,4 2.052,4.219 0.938,0.219 10 false *a 0.552,3.833 1.01,4.031 0.458,0.198 10 false *f
*a 1400 mm (4.59 ft.)
*b String 2
*c String 4
*d Mark K
*e Mark L
*f Mark M
*g Mark N


Secure string (4) so that it passes through marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



v.

Mark positions on string (4), 1400 mm (4.59 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


vi.
E287106C01
2.583,2.948 2.833,2.667 false 1.917,4.25 1.833,3.667 false 1.375,3.604 1.302,3.396 1.302,3.396 1.385,3.396 false 2.052,3.604 2.135,3.396 2.135,3.396 2.052,3.396 false 3.167,3.885 3.167,3.635 3.167,3.635 3.052,3.635 false 1.5,4 1.5,3.729 1.5,3.729 1.344,3.729 false 2.583,4.25 2.333,4.021 false 2.354,3.74 2.781,3.969 false 0.792,4.063 0.99,3.656 false 1.115,3.625 0.792,3.281 false 2.323,3.635 2.573,3.354 false 2.885,2.583 3.302,2.75 0.417,0.167 10 false *f 2.802,3.99 3.167,4.344 0.365,0.354 10 false *d 1.875,4.313 2.708,4.479 0.833,0.167 10 false *e 1.427,4.042 2.01,4.208 0.583,0.167 10 false *c 2.531,4.292 3.115,4.458 0.583,0.167 10 false *a 3.115,3.917 3.396,4.135 0.281,0.219 10 false *b 1.448,3.333 1.698,3.5 0.25,0.167 10 false *h 1.865,3.333 2.115,3.5 0.25,0.167 10 false *g 0.677,4.125 1.375,4.458 0.698,0.333 10 false *d 0.719,3.146 1.417,3.479 0.698,0.333 10 false *i 2.552,3.208 3.25,3.542 0.698,0.333 10 false *j
*a 800 mm (2.62 ft.)
*b 100 mm (0.33 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g Mark K
*h Mark L
*i Mark M
*j Mark N


Place and secure the cross check markers, centered on marks M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




vii.

Place the check marker between marks K and L.


viii.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 6: SET SST (REAR ADJUSTMENT)


a.

To the rear of the vehicle, extend string (4) perpendicular to the vehicle center line (string (2)), and place SST.

SST
09870-52010  09870-52020  

i.
E439841C01
1.719,1.104 2.208,0.854 false 1.24,4.021 1.698,3.573 false 2.833,3.135 2.552,2.823 false 1.708,2.823 1.01,2.271 true 2.698,3.708 2.344,3.406 false 1.094,3.208 0.771,3.354 false 2.083,4.146 1.729,3.844 false 0.583,3.302 1,3.542 0.417,0.24 10 false *a 1.063,3.99 1.542,4.25 0.479,0.26 10 false *f 2.74,3.688 3.271,3.969 0.531,0.281 10 false *b 2.906,3.125 3.313,3.385 0.406,0.26 10 false *d 0.823,2.198 1.302,2.458 0.479,0.26 10 false *c 2.271,0.771 2.75,1.031 0.479,0.26 10 false *e 2.156,4.156 2.635,4.417 0.479,0.26 10 false *g
*a 1450 mm (4.76 ft.)
*b 2650 mm (8.69 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark J
*g Mark X


Mark a position on string (2) to the rear of the vehicle, 1450 mm (4.76 ft.) from the datum point. (Mark J)


ii.

Mark a position on string (2) to the rear of the vehicle, 2650 mm (8.69 ft.) from the datum point. (Mark X)


iii.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



v.
E287144C03
1.708,0.896 2.208,0.542 false 1,3.052 1.396,3.354 false 0.677,3.802 1.094,3.354 false 2.385,3.042 2.073,3.344 false 2.875,3.646 2.677,3.344 false 2.615,3.802 2.313,3.344 false 2.167,3.969 1.969,3.667 false 1.188,3.979 1.417,3.667 false 2.292,0.49 2.75,0.688 0.458,0.198 10 false *b 0.823,2.938 1.281,3.135 0.458,0.198 10 false *e 2.438,2.969 2.896,3.167 0.458,0.198 10 false *d 2.844,3.698 3.302,3.896 0.458,0.198 10 false *c 2.542,3.854 3,4.052 0.458,0.198 10 false *g 2.167,4.042 3.104,4.26 0.938,0.219 10 false *a 1.115,4 2.052,4.219 0.938,0.219 10 false *a 0.552,3.833 1.01,4.031 0.458,0.198 10 false *f
*a 1450 mm (4.76 ft.)
*b String 2
*c String 4
*d Mark K
*e Mark L
*f Mark AC
*g Mark AD


Secure string (4) so that it passes through marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



vi.

Mark positions on string (4), 1450 mm (4.76 ft.) to the left and right of the vehicle center line (string (2)). (Marks AC and AD)


vii.
E439705C02
2.583,2.948 2.833,2.667 false 0.833,3.26 1.177,2.969 false 3.104,4.26 2.854,4.031 true 1.26,3.865 1.708,3.354 false 2.344,3.292 2.427,3.469 false 1.719,0.573 1.385,0.385 false 2.417,4.448 2.729,4.281 true 2.052,3.094 2.24,2.969 false 2.76,3.49 3.083,3.271 true 2.885,2.583 3.302,2.75 0.417,0.167 10 false *f 2.219,4.375 2.469,4.604 0.25,0.229 10 false *d 1.198,0.281 2.031,0.448 0.833,0.167 10 false *e 3.135,3.177 3.406,3.365 0.271,0.188 10 false *c 0.167,1.375 0.75,1.542 0.583,0.167 10 false *a 3.115,4.302 3.396,4.521 0.281,0.219 10 false *b 1.865,3.042 2.115,3.208 0.25,0.167 10 false *h 0.677,3.229 0.927,3.396 0.25,0.167 10 false *g 1.104,3.865 1.802,4.198 0.698,0.333 10 false *i 3.094,1.365 3.365,1.531 0.271,0.167 10 false *a 2.167,3.188 2.438,3.354 0.271,0.167 10 false *a
*a SST (Television Camera Adjustment Target)
*b SST (L Type Stand)
*c SST (Television Camera Adjustment Target) Center Line
*d SST (L Type Stand) Center Line
*e String 2
*f String 4
*g Mark AC
*h Mark AD
*i Mark X


While the center line of SST (television camera adjustment target) is aligned with mark X, place string (2) so that it overlaps the center line of SST (L type stand) as shown in the illustration.


viii.

Align the center line of SST (television camera adjustment target) with marks AC and AD and place it parallel with string (4) as shown in the illustration


ix.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 7: SET MARKERS (LEFT-SIDE ADJUSTMENT)


a.

At the left side of the vehicle, extend string (5) parallel to the vehicle center line (string (2)), and place a marker

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1400 mm (4.59 ft.)
*b 3700 mm (12.14 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string (2) in front of the vehicle, 3700 mm (12.14 ft.) from the datum point. (Mark E)


ii.

Mark the position on string (2) to the rear of the vehicle, 1400 mm (4.59 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287146C03
0.563,0.5 1.094,1.073 false 1.135,1.438 1.406,1.063 false 2.042,1.052 2.177,0.583 false 2.552,1.063 2.792,0.594 false 2.583,3.719 2.74,3.958 false 2.052,3.719 2.208,3.958 false 1.104,3.417 1.385,3.708 false 0.781,4.073 1.083,3.708 false 1.365,4.021 1.469,4.281 false 1.365,0.771 1.438,0.438 false 1.719,4.177 1.875,4.417 false 0.385,0.417 0.698,0.615 0.313,0.198 10 false *g 1.385,0.26 2.021,0.469 0.635,0.208 10 false *a 0.99,1.469 1.302,1.667 0.313,0.198 10 false *e 2.156,0.427 2.469,0.625 0.313,0.198 10 false *f 2.781,0.427 3.188,0.667 0.406,0.24 10 false *c 2.719,3.99 3.125,4.229 0.406,0.24 10 false *d 2.156,3.99 2.469,4.188 0.313,0.198 10 false *h 1.427,4.313 2.063,4.521 0.635,0.208 10 false *a 0.656,4.094 1.063,4.365 0.406,0.271 10 false *j 0.938,3.323 1.25,3.521 0.313,0.198 10 false *i 1.917,4.438 2.552,4.646 0.635,0.208 10 false *b
*a 1200 mm (3.94 ft.)
*b String 2
*c String 3
*d String 4
*e Mark F
*f Mark G
*g Mark H
*h Mark K
*i Mark L
*j Mark M


Secure strings (3) and (4) so that they pass through marks F and G, marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings (3) and (4), 1200 mm (3.94 ft.) to the left of the vehicle center line (string 2). (Marks H and M)


ix.
E395048C01
2.396,2.958 2.583,2.677 false 1.563,3.938 1.698,3.823 false 2.5,1 2.688,0.719 false 0.656,3.594 0.448,3.333 false 1.094,0.688 1.281,0.406 false 0.865,1.271 1.094,1.021 false 0.865,3.854 1.094,3.604 false 2.563,2.51 2.875,2.708 0.313,0.198 10 false *a 1.385,3.906 1.698,4.104 0.313,0.198 10 false *b 2.656,0.552 2.969,0.75 0.313,0.198 10 false *c 0.333,3.167 0.646,3.365 0.313,0.198 10 false *d 1.25,0.25 1.563,0.448 0.313,0.198 10 false *e 0.698,1.292 1.01,1.49 0.313,0.198 10 false *f 0.719,3.906 1.031,4.104 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f Mark H
*g Mark M


Secure string (5) so that it passes through marks H and M as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.
E287147C01
0.771,0.771 1.385,1.021 false 0.781,0.385 1.396,0.635 false 1.406,1.531 1.24,1.365 false 1.385,1.677 1.229,1.792 false 1.385,2.208 1.188,2.083 false 1.396,2.354 1.281,2.51 false 2.531,2.979 2.656,3.219 false 1.385,3.594 1.563,3.75 false 0.24,2.354 0.125,2.354 0.125,2.354 0.125,2.635 false 0.51,2.354 0.396,2.354 0.396,2.354 0.396,2.635 false 0.802,2.354 0.688,2.354 0.688,2.354 0.688,2.635 false 1.063,2.51 0.948,2.51 0.948,2.51 0.948,2.792 false 0.615,0.313 1.073,0.51 0.458,0.198 10 false *f 0.604,0.677 0.917,0.885 0.313,0.208 10 false *g 1.104,1.24 1.563,1.438 0.458,0.198 10 false *l 1.073,1.792 1.531,1.99 0.458,0.198 10 false *k 1.073,1.969 1.531,2.167 0.458,0.198 10 false *j 1.208,2.552 1.667,2.75 0.458,0.198 10 false *i 2.625,3.281 3.083,3.479 0.458,0.198 10 false *e 1.615,3.771 2.073,3.969 0.458,0.198 10 false *h 0.865,2.833 1.802,3.104 0.938,0.271 10 false *a 0.594,2.698 1.531,2.969 0.938,0.271 10 false *b 0.333,2.677 1.271,2.948 0.938,0.271 10 false *c 0.042,2.677 0.313,2.896 0.271,0.219 10 false *d
*a 1000 mm (3.28 ft.)
*b 1200 mm (3.94 ft.)
*c 2200 mm (7.22 ft.)
*d 2400 mm (7.87 ft.)
*e String 1
*f String 5
*g Mark H
*h Mark M
*i Mark O
*j Mark P
*k Mark Q
*l Mark R


Make marks on string (5) that are 1000 mm (3.28 ft.), 1200 mm (3.94 ft.), 2200 mm (7.22 ft.) and 2400 mm (7.87 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xi.
E287107C01
1.094,3.615 0.75,3.333 false 1.438,0.167 1.104,0.167 1.104,0.167 1.104,0.396 false 2,0.5 1.135,0.917 false 1.073,3.75 0.667,4.25 false 1.583,4 1.583,3.74 1.583,3.74 1.438,3.74 false 0.885,1.219 1.104,1.031 false 1.104,0.667 0.667,0.5 false 2.583,3.031 2.833,2.74 false 0.885,2.604 1.115,2.406 false 0.875,2.052 1.115,2.229 false 1.229,1.896 1.115,1.75 false 1.333,1.396 1.115,1.573 false 0.365,1.031 0.198,1.031 0.198,1.031 0.198,1.5 false 1.063,2.323 0.813,2.323 false 1.073,1.667 0.823,1.667 false 1.49,0.083 2.073,0.25 0.583,0.167 10 false *b 0.49,0.406 0.906,0.573 0.417,0.167 10 false *g 2.052,0.417 3.302,0.583 1.25,0.167 10 false *d 0.646,2.25 1.479,2.417 0.833,0.167 10 false *e 0.573,4.271 2.073,4.438 1.5,0.167 10 false *d 0.594,3.229 0.927,3.396 0.333,0.167 10 false *i 1.51,4.042 2.094,4.208 0.583,0.167 10 false *c 2.885,2.604 3.302,2.771 0.417,0.167 10 false *f 0.719,1.25 1.052,1.417 0.333,0.167 10 false *h 1.292,1.25 1.625,1.417 0.333,0.167 10 false *m 1.177,1.927 1.51,2.094 0.333,0.167 10 false *l 0.75,1.906 1.083,2.073 0.333,0.167 10 false *k 0.792,2.646 1.125,2.813 0.333,0.167 10 false *j 0.146,1.552 0.729,1.719 0.583,0.167 10 false *a 0.594,1.583 1.427,1.75 0.833,0.167 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 5
*h Mark H
*i Mark M
*j Mark O
*k Mark P
*l Mark Q
*m Mark R


Place and secure the cross check markers, centered on marks H and M.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks O and P, and marks Q and R.


xiii.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 8: SET SST (LEFT-SIDE ADJUSTMENT)


a.

At the left side of the vehicle, extend string (5) parallel to the vehicle center line (string (2)), and place SST.

SST
09870-52010  09870-52020  

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1450 mm (4.76 ft.)
*b 3750 mm (12.3 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string (2) in front of the vehicle, 3750 mm (12.3 ft.) from the datum point. (Mark E)


ii.

Mark the position on string (2) to the rear of the vehicle, 1450 mm (4.76 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E439864C03
0.75,1.49 1.094,1.073 false 1.135,1.438 1.406,1.063 false 2.042,1.052 2.177,0.583 false 2.552,1.063 2.792,0.594 false 2.583,3.719 2.74,3.958 false 2.052,3.719 2.208,3.958 false 1.104,3.417 1.385,3.708 false 0.76,3.458 1.083,3.708 false 1.719,4.177 1.875,4.417 false 0.552,4.073 0.813,3.719 false 0.49,1.323 0.802,1.083 false 2.229,0.479 2.542,0.677 0.313,0.198 10 false *g 1.271,0.594 1.906,0.802 0.635,0.208 10 false *a 2.823,3.969 3.135,4.167 0.313,0.198 10 false *e 0.99,1.469 1.302,1.667 0.313,0.198 10 false *f 1.927,4.375 2.333,4.615 0.406,0.24 10 false *c 2.833,0.479 3.24,0.719 0.406,0.24 10 false *d 0.563,1.458 0.875,1.656 0.313,0.198 10 false *h 1.292,3.854 1.927,4.063 0.635,0.208 10 false *a 0.958,3.354 1.365,3.625 0.406,0.271 10 false *j 2.292,3.927 2.604,4.125 0.313,0.198 10 false *i 1.167,4.323 1.802,4.531 0.635,0.208 10 false *b 0.583,3.365 0.896,3.563 0.313,0.198 10 false *k 0.323,3.99 0.635,4.188 0.313,0.198 10 false *m 0.302,1.292 0.615,1.49 0.313,0.198 10 false *l 1.125,0.365 1.76,0.573 0.635,0.208 10 false *b
*a 1250 mm (4.1 ft.)
*b 1450 mm (4.76 ft.)
*c String 2
*d String 3
*e String 4
*f Mark F
*g Mark G
*h Mark H
*i Mark K
*j Mark L
*k Mark M
*l Mark AA
*m Mark AC


Secure strings (3) and (4) so that they pass through marks F and G, marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings (3) and (4), 1250 mm (4.1 ft.) to the left of the vehicle center line (string 2). (Marks H and M)


ix.

Mark strings (3) and (4), 1450 mm (4.76 ft.) to the left of the vehicle center line (string 2). (Marks AA and AC)


x.
E395048C01
2.396,2.958 2.583,2.677 false 1.563,3.938 1.698,3.823 false 2.5,1 2.688,0.719 false 0.656,3.594 0.448,3.333 false 1.094,0.688 1.281,0.406 false 0.865,1.271 1.094,1.021 false 0.865,3.854 1.094,3.604 false 2.563,2.51 2.875,2.708 0.313,0.198 10 false *a 1.385,3.906 1.698,4.104 0.313,0.198 10 false *b 2.656,0.552 2.969,0.75 0.313,0.198 10 false *c 0.333,3.167 0.646,3.365 0.313,0.198 10 false *d 1.25,0.25 1.563,0.448 0.313,0.198 10 false *e 0.698,1.292 1.01,1.49 0.313,0.198 10 false *f 0.719,3.906 1.031,4.104 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f Mark H
*g Mark M


Secure string (5) so that it passes through marks H and M as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



xi.
E439840C01
0.771,0.771 1.385,1.021 false 0.781,0.385 1.396,0.635 false 1.385,1.594 1.198,1.396 false 0.927,2.229 0.771,2.344 false 2.531,2.979 2.656,3.219 false 1.385,3.594 1.563,3.75 false 1.031,1.313 1.49,1.51 0.458,0.198 10 false *f 1.615,3.708 2.073,3.906 0.458,0.198 10 false *e 0.604,2.313 1.542,2.583 0.938,0.271 10 false *a 2.656,3.229 2.99,3.458 0.333,0.229 10 false *b 0.594,0.281 1.531,0.552 0.938,0.271 10 false *c 0.563,0.677 0.833,0.896 0.271,0.219 10 false *d
*a 2200 mm (7.22 ft.)
*b String 1
*c String 5
*d Mark H
*e Mark M
*f Mark Y


Make a mark on string (5) that is 2200 mm (7.22 ft.) from the reference line (string (1)) as shown in the illustration. (Mark Y)


xii.
E439706C02
1.458,3.167 1.677,3.438 false 2.833,0.969 2.552,1.198 false 2.594,3.448 2.885,3.688 false 1.656,1.698 1.385,1.563 false 1.688,0.792 1.938,0.5 false 1.823,1.021 1.688,1.198 false 1.052,1.385 1.385,1.208 false 1.115,3.146 1.375,3.438 false 2.896,0.865 3.313,1.021 0.417,0.156 10 false *b 1.219,1.5 1.635,1.667 0.417,0.167 10 false *g 1.979,0.396 2.26,0.583 0.281,0.188 10 false *d 2.938,3.656 3.219,3.844 0.281,0.188 10 false *c 1.313,3.073 1.729,3.24 0.417,0.167 10 false *f 0.229,0.177 0.813,0.344 0.583,0.167 10 false *a 1.885,0.938 2.25,1.135 0.365,0.198 10 false *e 0.229,1.771 0.813,1.938 0.583,0.167 10 false *a 0.229,3.583 0.479,3.75 0.25,0.167 10 false *a 0.833,1.333 1.25,1.5 0.417,0.167 10 false *h 0.969,3.073 1.385,3.24 0.417,0.167 10 false *i
*a SST (Television Camera Adjustment Target)
*b String 3
*c String 4
*d String 5
*e Mark H
*f Mark M
*g Mark Y
*h Mark AA
*i Mark AC


Align the center line of SST (television camera adjustment target) with mark AA and place it parallel with string (3) as shown in the illustration.


xiii.

Align the center line of SST (television camera adjustment target) with mark AC and place it parallel with string (4) as shown in the illustration.


xiv.

Align the center line of SST (television camera adjustment target) with mark Y and place it parallel with string (5) as shown in the illustration.

NOTICE:

The vertical direction of SST (television camera adjustment target) differs depending on whether corner setting or side setting is used.



xv.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 9: SET MARKERS (RIGHT-SIDE ADJUSTMENT)


a.

At the right side of the vehicle, extend string (6) parallel to the vehicle center line (string (2)), and place a marker.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1400 mm (4.59 ft.)
*b 3700 mm (12.14 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string (2) in front of the vehicle, 3700 mm (12.14 ft.) from the datum point. (Mark E)


ii.

Mark the position on string (2) to the rear of the vehicle, 1400 mm (4.59 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287712C03
0.927,0.49 1.344,1.052 false 2,1.063 2.229,1.469 false 2.313,1.063 2.792,0.385 false 2.5,1.063 2.896,1.323 false 2.813,3.615 2.906,3.354 false 2.313,3.635 2.573,3.948 false 2.01,3.615 2.219,3.354 false 1.354,3.625 1.125,3.344 false 1.969,3.938 2.094,4.188 false 1.99,0.76 2.146,0.448 false 1.302,4.021 1.677,3.781 false 2.115,0.313 3.188,0.51 1.073,0.198 10 false *a 2.052,4.229 2.438,4.438 0.385,0.208 10 false *a 2.958,3.208 3.271,3.406 0.313,0.198 10 false *d 2.219,1.563 2.531,1.76 0.313,0.198 10 false *f 1.115,3.969 1.448,4.198 0.333,0.229 10 false *b 0.75,0.375 1.063,0.573 0.313,0.198 10 false *e 2.99,1.365 3.281,1.594 0.292,0.229 10 false *c 2.854,0.219 3.167,0.417 0.313,0.198 10 false *g 0.99,3.188 1.302,3.385 0.313,0.198 10 false *i 2.24,3.177 2.552,3.375 0.313,0.198 10 false *h 2.552,4.021 2.875,4.229 0.323,0.208 10 false *j
*a 1200 mm (3.94 ft.)
*b String 2
*c String 3
*d String 4
*e Mark F
*f Mark G
*g Mark I
*h Mark K
*i Mark L
*j Mark N


Secure strings (3) and (4) so that they pass through marks F and G and marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings (3) and (4), 1200 mm (3.94 ft.) to the right of the vehicle center line (string 2). (Marks I and N)


ix.
E395049C01
2.51,2.948 2.688,2.656 false 1.51,3.906 1.719,3.813 false 2.573,0.99 2.719,0.74 false 0.688,3.594 0.458,3.313 false 2.313,0.688 2.49,0.396 false 2.313,1.01 2.604,1.354 false 2.313,3.594 2.604,3.938 false 2.667,2.5 2.979,2.698 0.313,0.198 10 false *a 1.323,3.875 1.635,4.073 0.313,0.198 10 false *b 2.698,0.594 3.01,0.792 0.313,0.198 10 false *c 0.302,3.156 0.615,3.354 0.313,0.198 10 false *d 2.5,0.229 2.813,0.427 0.313,0.198 10 false *e 2.646,1.365 2.958,1.563 0.313,0.198 10 false *f 2.635,3.938 2.948,4.135 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 6
*f Mark I
*g Mark N


Secure string (6) so that it passes through marks I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.
E287713C01
2.01,0.781 2.365,0.573 false 1.823,0.729 2.021,1.021 false 2.26,1.333 2.021,1.531 false 2.229,1.833 2.031,1.667 false 1.885,2.01 2.01,2.219 false 1.896,2.531 2.01,2.344 false 0.656,3.125 0.771,3.125 0.771,3.125 0.875,2.969 false 2.99,2.76 2.99,2.563 2.99,2.563 3.167,2.563 false 1.854,3.792 2.01,3.615 false 2.448,2.75 2.448,2.552 2.448,2.552 2.604,2.552 false 2.729,2.75 2.729,2.552 2.729,2.552 2.885,2.552 false 2.177,2.74 2.177,2.542 2.177,2.542 2.333,2.542 false 1.646,0.615 1.958,0.813 0.313,0.198 10 false *g 2.427,0.51 2.958,0.75 0.531,0.24 10 false *f 2.313,1.229 2.625,1.427 0.313,0.198 10 false *l 2.219,1.865 2.531,2.063 0.313,0.198 10 false *k 1.813,1.844 2.125,2.042 0.313,0.198 10 false *j 1.833,2.552 2.146,2.75 0.313,0.198 10 false *i 0.438,3.042 0.906,3.292 0.469,0.25 10 false *e 1.677,3.76 1.99,3.958 0.313,0.198 10 false *h 2.927,2.792 3.26,3.021 0.333,0.229 10 false *d 2.677,2.792 2.969,3.031 0.292,0.24 10 false *c 2.104,2.792 3.063,3 0.958,0.208 10 false *a 2.385,2.792 3.344,3 0.958,0.208 10 false *b
*a 1000 mm (3.28 ft.)
*b 1200 mm (3.94 ft.)
*c 2200 mm (7.22 ft.)
*d 2400 mm (7.87 ft.)
*e String 1
*f String 6
*g Mark I
*h Mark N
*i Mark S
*j Mark T
*k Mark U
*l Mark V


Make marks on string (6) that are 1000 mm (3.28 ft.), 1200 mm (3.94 ft.), 2200 mm (7.22 ft.) and 2400 mm (7.87 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xi.
E287108C01
1.5,0.583 2.292,0.917 false 2.563,1.406 2.323,1.573 false 2.615,1.896 2.323,1.76 false 2.198,2.583 2.333,2.406 false 2.74,3.375 2.365,3.25 false 3.167,1.333 3.167,1.031 3.167,1.031 3.063,1.031 false 2.5,3.021 2.75,2.729 false 2.323,0.667 2.75,0.333 false 2.323,0.396 2.323,0.167 2.323,0.167 2.083,0.167 false 1.99,3.74 1.833,3.74 1.833,3.74 1.833,4.25 false 2.333,3.615 2.552,3.927 false 2.198,2.01 2.333,2.229 false 2.333,1.01 2.75,0.667 false 2.656,1.667 2.354,1.667 false 2.656,2.302 2.354,2.302 false 1.292,0.51 2.542,0.677 1.25,0.167 10 false *d 2.719,1.604 3.333,1.76 0.615,0.156 10 false *e 2.74,3.375 3.125,3.646 0.385,0.271 10 false *d 1.781,4.292 2.365,4.458 0.583,0.167 10 false *c 2.604,3.927 2.938,4.094 0.333,0.167 10 false *i 2.802,2.583 3.219,2.75 0.417,0.167 10 false *f 3.104,1.385 3.417,1.594 0.313,0.208 10 false *a 2.802,0.583 3.135,0.75 0.333,0.167 10 false *h 2.802,0.25 3.219,0.417 0.417,0.167 10 false *g 1.917,0.104 2.5,0.271 0.583,0.167 10 false *b 2.583,1.323 2.917,1.49 0.333,0.167 10 false *m 2.656,1.865 2.99,2.031 0.333,0.167 10 false *l 2.135,1.844 2.385,2.042 0.25,0.198 10 false *k 2.135,2.625 2.469,2.792 0.333,0.167 10 false *j 2.698,2.229 3.313,2.385 0.615,0.156 10 false *e
*a 100 mm (0.33 ft.)
*b 800 mm (2.62 ft.)
*c 400 mm (1.31 ft.)
*d Cross Check Marker
*e Check Marker
*f String 1
*g String 6
*h Mark I
*i Mark N
*j Mark S
*k Mark T
*l Mark U
*m Mark V


Place and secure the cross check markers, centered on marks I and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.




xii.

Place check markers between marks S and T, and marks U and V.


xiii.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 10: SET SST (RIGHT-SIDE ADJUSTMENT)


a.

At the left side of the vehicle, extend string (6) parallel to the vehicle center line (string (2)), and place SST.

SST
09870-52010  09870-52020  

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1450 mm (4.76 ft.)
*b 3750 mm (12.3 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string (2) in front of the vehicle, 3750 mm (12.3 ft.) from the datum point. (Mark E)


ii.

Mark the position on string (2) to the rear of the vehicle, 1450 mm (4.76 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E439863C01
0.927,0.49 1.344,1.052 false 2,1.063 2.229,1.469 false 2.583,1.375 2.302,1.063 false 0.74,1.063 0.406,1.396 false 0.708,3.615 0.469,3.344 false 2.313,3.635 2.625,3.24 false 2.01,3.615 2.219,3.354 false 1.354,3.625 1.125,3.344 false 2.604,1.063 2.906,1.333 false 2.604,3.615 2.896,3.385 false 1.302,4.021 1.677,3.781 false 1.927,0.583 3,0.781 1.073,0.198 10 false *a 1.896,3.781 2.281,3.99 0.385,0.208 10 false *a 0.229,1.344 0.542,1.542 0.313,0.198 10 false *d 0.76,0.375 1.073,0.573 0.313,0.198 10 false *f 2.031,4.219 2.365,4.448 0.333,0.229 10 false *b 0.24,3.26 0.552,3.458 0.313,0.198 10 false *e 1.125,3.969 1.417,4.198 0.292,0.229 10 false *c 2.281,1.469 2.594,1.667 0.313,0.198 10 false *g 2.26,3.24 2.573,3.438 0.313,0.198 10 false *i 2.604,1.427 2.917,1.625 0.313,0.198 10 false *h 0.958,3.25 1.281,3.458 0.323,0.208 10 false *j 2.021,0.26 2.354,0.49 0.333,0.229 10 false *b 2.667,3.156 2.979,3.354 0.313,0.198 10 false *k 2.948,3.323 3.26,3.521 0.313,0.198 10 false *m 2.958,1.354 3.271,1.552 0.313,0.198 10 false *l
*a 1250 mm (4.1 ft.)
*b 1450 mm (4.76 ft.)
*c String 2
*d String 3
*e String 4
*f Mark F
*g Mark G
*h Mark I
*i Mark K
*j Mark L
*k Mark N
*l Mark AB
*m Mark AD


Secure strings (3) and (4) so that they pass through marks F and G and marks K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark strings (3) and (4), 1250 mm (4.1 ft.) to the right of the vehicle center line (string 2). (Marks I and N)


ix.

Mark strings (3) and (4), 1450 mm (4.76 ft.) to the right of the vehicle center line (string 2). (Marks AB and AD)


x.
E395049C01
2.51,2.948 2.688,2.656 false 1.51,3.906 1.719,3.813 false 2.573,0.99 2.719,0.74 false 0.688,3.594 0.458,3.313 false 2.313,0.688 2.49,0.396 false 2.313,1.01 2.604,1.354 false 2.313,3.594 2.604,3.938 false 2.667,2.5 2.979,2.698 0.313,0.198 10 false *a 1.323,3.875 1.635,4.073 0.313,0.198 10 false *b 2.698,0.594 3.01,0.792 0.313,0.198 10 false *c 0.302,3.156 0.615,3.354 0.313,0.198 10 false *d 2.5,0.229 2.813,0.427 0.313,0.198 10 false *e 2.646,1.365 2.958,1.563 0.313,0.198 10 false *f 2.635,3.938 2.948,4.135 0.313,0.198 10 false *g
*a String 1
*b String 2
*c String 3
*d String 4
*e String 6
*f Mark I
*g Mark N


Secure string (6) so that it passes through marks I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



xi.
E439838C01
2,1.021 2.531,0.75 false 1.354,0.417 1.969,0.667 false 2.26,1.375 1.99,1.604 false 2.625,2.406 2.417,2.344 false 2.531,2.979 2.656,3.219 false 2,3.615 2.177,3.771 false 2.333,1.302 2.792,1.5 0.458,0.198 10 false *f 2.25,3.74 2.708,3.938 0.458,0.198 10 false *e 2.688,2.375 3.323,2.677 0.635,0.302 10 false *a 2.656,3.229 2.99,3.458 0.333,0.229 10 false *b 1.156,0.313 1.438,0.563 0.281,0.25 10 false *c 2.615,0.635 2.885,0.854 0.271,0.219 10 false *d
*a 2200 mm (7.22 ft.)
*b String 1
*c String 6
*d Mark I
*e Mark N
*f Mark Z


Make a mark on string (6) that is 2200 mm (7.22 ft.) from the reference line (string (1)) as shown in the illustration. (Mark Z)


xii.
E439707C02
1.625,3.438 1.896,3.135 false 1.615,0.75 1.26,0.427 false 0.667,3.448 0.448,3.698 false 1.896,1.594 1.625,1.708 false 0.719,1.198 0.51,0.865 false 1.615,1.208 1.469,1.031 false 1.906,3.427 2.271,3.198 false 2.167,1.333 1.906,1.208 false 0.344,0.76 0.76,0.917 0.417,0.156 10 false *b 1.969,1.531 2.385,1.698 0.417,0.167 10 false *g 1.063,0.333 1.344,0.521 0.281,0.188 10 false *d 0.26,3.677 0.542,3.865 0.281,0.188 10 false *c 1.927,3.031 2.344,3.198 0.417,0.167 10 false *f 2.938,0.208 3.427,0.396 0.49,0.188 10 false *a 1.281,0.927 1.646,1.125 0.365,0.198 10 false *e 2.917,1.792 3.313,2.021 0.396,0.229 10 false *a 2.906,3.604 3.156,3.771 0.25,0.167 10 false *a 2.344,3.135 2.76,3.302 0.417,0.167 10 false *i 2.24,1.292 2.656,1.458 0.417,0.167 10 false *h
*a SST (Television Camera Adjustment Target)
*b String 3
*c String 4
*d String 6
*e Mark I
*f Mark N
*g Mark Z
*h Mark AB
*i Mark AD


Align the center line of SST (television camera adjustment target) with mark AB and place it parallel with string (3) as shown in the illustration.


xiii.

Align the center line of SST (television camera adjustment target) with mark AD and place it parallel with string (4) as shown in the illustration.


xiv.

Align the center line of SST (television camera adjustment target) with mark Z and place it parallel with string (6) as shown in the illustration.

NOTICE:

The vertical direction of SST (television camera adjustment target) differs depending on whether corner setting or side setting is used



xv.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 11: SET MARKERS (ADJUSTMENT OF ALL CAMERAS)


a.

At the right and left sides of the vehicle, extend strings (5) and (6) parallel to the vehicle center line (string 2), and place markers.

i.
E287145C01
1.719,0.76 2.344,0.479 false 1.719,1.042 2.302,0.865 false 2.292,2.99 2.563,2.625 false 1.719,2.99 2.313,3.49 false 1.719,3.688 2.042,4.135 false 0.323,1.875 0.438,1.583 0.438,1.583 0.573,1.583 false 0.323,3.458 0.438,3.167 0.438,3.167 0.573,3.167 false 2.396,0.417 2.854,0.615 0.458,0.198 10 false *e 2.385,0.813 2.844,1.01 0.458,0.198 10 false *f 2.604,2.563 3.063,2.76 0.458,0.198 10 false *d 2.396,3.458 3.219,3.76 0.823,0.302 10 false *c 2.021,4.156 2.479,4.354 0.458,0.198 10 false *g 0.24,3.479 1.094,3.708 0.854,0.229 10 false *a 0.208,1.917 1.063,2.146 0.854,0.229 10 false *b
*a 1400 mm (4.59 ft.)
*b 3700 mm (12.14 ft.)
*c Datum Point
*d String 1
*e String 2
*f Mark E
*g Mark J


Mark the position on string (2) in front of the vehicle, 3700 mm (12.14 ft.) from the datum point. (Mark E)


ii.

Mark the position on string (2) to the rear of the vehicle, 1400 mm (4.59 ft.) from the datum point. (Mark J)


iii.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


iv.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



v.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



vii.
E287148C01
0.615,0.708 0.76,0.708 0.76,0.708 1.094,1.052 false 1.042,1.552 1.188,1.552 1.188,1.552 1.396,1.063 false 2.344,1.531 2.167,1.531 2.167,1.531 2.042,1.063 false 2.76,0.292 2.583,0.292 2.583,0.292 2.354,1.073 false 2.865,0.719 2.688,0.719 2.688,0.719 2.573,1.052 false 2.292,3.135 2.146,3.135 2.146,3.135 2.042,3.448 false 2.75,4.177 2.604,4.177 2.604,4.177 2.365,3.458 false 2.76,3.75 2.646,3.75 2.646,3.75 2.563,3.458 false 2.021,4.323 1.906,4.323 1.906,4.323 1.719,4.042 false 0.833,3.719 0.969,3.719 0.969,3.719 1.083,3.458 false 0.979,3.115 1.115,3.115 1.115,3.115 1.406,3.448 false 1.375,0.76 1.271,0.375 false 2,0.76 2.125,0.396 false 1.313,3.99 1.385,3.76 false 2.135,3.99 2.073,3.76 false 1.188,0.229 2.26,0.427 1.073,0.198 10 false *a 2.083,0.24 3.156,0.438 1.073,0.198 10 false *a 0.417,0.646 0.865,0.833 0.448,0.188 10 false *g 2.948,0.656 3.396,0.844 0.448,0.188 10 false *c 2.833,0.229 3.281,0.417 0.448,0.188 10 false *h 0.781,1.479 1.229,1.667 0.448,0.188 10 false *e 2.396,1.469 2.844,1.656 0.448,0.188 10 false *f 2.354,3.083 2.802,3.271 0.448,0.188 10 false *i 0.802,3.063 1.25,3.25 0.448,0.188 10 false *j 0.667,3.667 1.115,3.854 0.448,0.188 10 false *k 2.813,4.125 3.26,4.313 0.448,0.188 10 false *l 2.833,3.698 3.281,3.885 0.448,0.188 10 false *d 2.094,4.26 2.542,4.448 0.448,0.188 10 false *b 2.094,4.031 2.823,4.25 0.729,0.219 10 false *a 1.208,4.01 1.938,4.229 0.729,0.219 10 false *a
*a 1200 mm (3.94 ft.)
*b String 2
*c String 3
*d String 4
*e Mark F
*f Mark G
*g Mark H
*h Mark I
*i Mark K
*j Mark L
*k Mark M
*l Mark N


Secure strings (3) and (4) so that they pass through marks F, G, K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



viii.

Mark string (3), 1200 mm (3.94 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I)


ix.

Mark string (4), 1200 mm (3.94 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


x.
E287132C02
1.094,0.688 1.292,0.271 false 2.302,0.667 2.688,0.177 false 2.604,1 2.875,0.677 false 2.625,1.375 2.302,1.01 false 0.781,1.385 1.104,1 false 0.458,3.26 0.698,3.583 false 0.771,4.031 1.094,3.594 false 1.552,3.833 1.708,3.74 false 2.646,3.948 2.313,3.594 false 2.635,2.646 2.469,2.958 false 1.344,0.198 1.802,0.396 0.458,0.198 10 false *e 2.75,0.104 3.208,0.302 0.458,0.198 10 false *f 2.938,0.604 3.396,0.802 0.458,0.198 10 false *c 2.688,1.396 3.146,1.594 0.458,0.198 10 false *h 0.625,1.417 1.083,1.615 0.458,0.198 10 false *g 0.313,3.104 0.771,3.302 0.458,0.198 10 false *d 0.646,4.073 1.104,4.271 0.458,0.198 10 false *i 1.375,3.875 1.833,4.073 0.458,0.198 10 false *b 2.667,4 3.125,4.198 0.458,0.198 10 false *j 2.729,2.573 3.188,2.771 0.458,0.198 10 false *a
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f String 6
*g Mark H
*h Mark I
*i Mark M
*j Mark N


Secure strings (5) and (6) so that they pass through marks H, M, I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



xi.
E288356C02
2.542,3.885 2.354,3.885 2.354,3.885 2.281,3.604 false 0.396,3.26 0.531,3.26 0.531,3.26 0.552,2.979 false 2.344,2.615 2.188,2.615 2.188,2.615 2.177,2.75 false 2.594,2.615 2.479,2.615 2.479,2.615 2.469,2.75 false 2.875,2.615 2.74,2.615 2.74,2.615 2.729,2.75 false 3.167,2.625 3.031,2.625 3.031,2.625 3.021,2.76 false 0.781,0.75 0.635,0.5 0.635,0.5 0.479,0.5 false 1.396,0.76 1.25,0.51 1.25,0.51 1.094,0.51 false 2.021,0.719 2.146,0.458 2.146,0.458 2.385,0.458 false 2.344,1.021 2.469,0.76 2.469,0.76 2.708,0.76 false 2.021,1.521 2.115,1.313 2.115,1.313 2.24,1.313 false 2.031,2.208 2.125,2 2.125,2 2.25,2 false 0.792,1.531 0.677,1.333 0.677,1.333 0.479,1.333 false 0.792,2.208 0.677,2.01 0.677,2.01 0.479,2.01 false 0.771,2.354 0.688,2.5 0.688,2.5 0.542,2.5 false 0.781,1.688 0.698,1.833 0.698,1.833 0.552,1.833 false 1.906,1.865 2.021,1.677 false 1.896,2.542 2.01,2.354 false 2.104,2.76 2.417,2.917 0.313,0.156 10 false *a 2.396,2.771 2.708,2.927 0.313,0.156 10 false *b 2.667,2.75 2.979,2.906 0.313,0.156 10 false *c 2.969,2.771 3.281,2.927 0.313,0.156 10 false *d 0.198,3.177 0.51,3.333 0.313,0.156 10 false *e 0.958,0.448 1.271,0.604 0.313,0.156 10 false *f 2.75,0.677 3.063,0.833 0.313,0.156 10 false *g 2.625,3.813 2.938,3.969 0.313,0.156 10 false *h 0.344,0.438 0.656,0.594 0.313,0.156 10 false *i 2.438,0.396 2.75,0.552 0.313,0.156 10 false *j 0.375,2.458 0.688,2.615 0.313,0.156 10 false *k 0.344,1.948 0.656,2.104 0.313,0.156 10 false *l 0.344,1.75 0.656,1.906 0.313,0.156 10 false *m 0.302,1.271 0.615,1.427 0.313,0.156 10 false *n 1.802,2.552 2.115,2.708 0.313,0.156 10 false *o 2.271,1.927 2.583,2.083 0.313,0.156 10 false *p 1.823,1.875 2.135,2.031 0.313,0.156 10 false *q 2.281,1.24 2.594,1.396 0.313,0.156 10 false *r
*a 1000 mm (3.28 ft.)
*b 1200 mm (3.94 ft.)
*c 2200 mm (7.22 ft.)
*d 2400 mm (7.87 ft.)
*e String 1
*f String 2
*g String 3
*h String 4
*i String 5
*j String 6
*k Mark O
*l Mark P
*m Mark Q
*n Mark R
*o Mark S
*p Mark T
*q Mark U
*r Mark V


Make marks on string (5) that are 1000 mm (3.28 ft.), 1200 mm (3.94 ft.), 2200 mm (7.22 ft.) and 2400 mm (7.87 ft.) from the datum line (string 1) as shown in the illustration. (Marks O, P, Q and R)


xii.

Make marks on string (6) that are 1000 mm (3.28 ft.), 1200 mm (3.94 ft.), 2200 mm (7.22 ft.) and 2400 mm (7.87 ft.) from the datum line (string 1) as shown in the illustration. (Marks S, T, U and V)


xiii.

Place and secure the cross check markers, centered on marks H, I, M and N.

NOTICE:
·

Align the cross check markers perpendicular to the string.

·

Make each arm of the cross check markers 800 mm (2.62 ft.) long and 100 mm (0.33 ft.) wide.

·

Extend the rear cross check markers to string 1.



E287112C01
4.26,2.052 4.583,1.917 false 4.26,2.792 4.583,2.667 false 4.25,2.25 4.583,2.375 false 4.25,2.99 4.583,3.115 false 2.573,2.385 2.896,2.25 false 2.573,3.115 2.896,2.979 false 2.573,1.927 2.906,2.052 false 2.563,2.667 2.896,2.792 false 4.365,1.406 4.833,0.917 false 4.271,2.896 5.708,2.521 5.708,2.521 4.292,2.135 false 2.5,1.167 2.896,1.427 false 4.26,0.26 4.26,0.167 4.26,0.167 4.677,0.167 false 5.469,1.448 5.635,1.448 5.635,1.448 5.635,1.75 false 2.5,4.667 2.896,4.365 false 4.667,4.667 4.26,4.365 false 3.417,5.469 3.417,4.396 false 3.083,4.75 3.208,4.375 false 4.083,4.75 3.958,4.375 false 4.906,3.708 5.24,3.354 false 3.927,1.146 4.01,1.146 4.01,1.146 3.958,1.438 false 3.24,1.146 3.156,1.146 3.156,1.146 3.198,1.438 false 4.26,1.438 4.438,1.635 false 3.531,1.417 3.729,0.521 false 2.865,2.906 1.156,2.51 1.156,2.51 2.875,2.146 false 2.865,1.271 2.385,0.625 false 4.281,4.51 4.667,5.25 false 2.865,4.51 2.406,5.25 false 3.354,5.5 4.188,5.667 0.833,0.167 10 false *d 2.99,4.781 3.24,4.948 0.25,0.167 10 false *k 2.354,4.677 2.688,4.844 0.333,0.167 10 false *l 4.031,4.792 4.281,4.958 0.25,0.167 10 false *j 4.698,4.698 4.948,4.865 0.25,0.167 10 false *m 5.292,3.302 5.708,3.469 0.417,0.167 10 false *e 4.635,3.063 4.969,3.229 0.333,0.167 10 false *r 4.635,2.583 4.969,2.75 0.333,0.167 10 false *s 4.635,2.323 4.969,2.49 0.333,0.167 10 false *t 4.635,1.833 4.969,2 0.333,0.167 10 false *u 4.75,0.104 5.333,0.271 0.583,0.167 10 false *b 4.885,0.833 6.135,1 1.25,0.167 10 false *c 5.563,1.792 6.146,1.958 0.583,0.167 10 false *a 3.75,1.083 4.083,1.25 0.333,0.167 10 false *g 3.302,1.083 3.635,1.25 0.333,0.167 10 false *f 2.292,1.063 2.625,1.229 0.333,0.167 10 false *h 2.396,1.833 2.667,2.052 0.271,0.219 10 false *q 2.385,2.323 2.719,2.49 0.333,0.167 10 false *p 2.365,2.604 2.698,2.771 0.333,0.167 10 false *o 2.406,3.125 2.74,3.292 0.333,0.167 10 false *n 0.969,2.448 1.802,2.615 0.833,0.167 10 false *d 4.479,1.604 4.813,1.771 0.333,0.167 10 false *i 3.74,0.365 4.323,0.531 0.583,0.167 10 false *d 5.802,2.438 6.635,2.604 0.833,0.167 10 false *d 2.302,0.469 3.552,0.635 1.25,0.167 10 false *c 4.677,5.302 5.927,5.469 1.25,0.167 10 false *c 2.313,5.313 3.563,5.479 1.25,0.167 10 false *c
*a 100 mm (0.33 ft.) *b 800 mm (2.62 ft.)
*c Cross Check Marker *d Check Marker
*e String 1 *f Mark F
*g Mark G *h Mark H
*i Mark I *j Mark K
*k Mark L *l Mark M
*m Mark N *n Mark O
*o Mark P *p Mark Q
*q Mark R *r Mark S
*s Mark T *t Mark U
*u Mark V - -



xiv.

Place check markers between marks F and G, marks K and L, marks O and P, marks Q and R, marks S and T, and marks U and V.


xv.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 12: SET MARKERS (SST ADJUSTMENT)


a.

Using SST (marker tool set), place the markers.

SST
09870-30010  

Markers and Spacers Used
Part Name Color Length Qty
Marker A White 800 mm (31.5 in.) 6
Marker B White 950 mm (37.4 in.) 2
Marker E White 350 mm (13.8 in.) 6
Marker F White 1000 mm (39.4 in.) 2
Marker G White 293 mm (11.5 in.) 4
Marker H White 200 mm (7.87 in.) 4
Spacer J Black 1000 mm (39.4 in.) 4
Spacer K Black 500 mm (19.69 in.) 2
Spacer N Black 200 mm (7.87 in.) 2
Spacer P Black 107 mm (4.21 in.) 4

i.
E452015C01
0.844,0.167 0.927,0.167 0.927,0.167 1.063,0.302 true 0.76,0.781 0.844,0.781 0.844,0.781 0.969,0.438 true 0.813,1 0.896,1 0.896,1 1.052,0.531 true 1.406,0.698 1.49,0.698 1.49,0.698 1.49,0.448 true 2.042,0.698 1.958,0.698 1.958,0.698 1.958,0.448 true 1.979,0.167 1.896,0.167 1.896,0.167 1.792,0.438 true 2.583,0.167 2.5,0.167 2.5,0.167 2.385,0.292 true 2.646,0.76 2.563,0.76 2.563,0.76 2.469,0.427 true 2.552,0.885 2.469,0.885 2.469,0.885 2.375,0.552 true 0.781,1.792 0.865,1.792 0.865,1.792 1.063,2.198 true 0.813,2.531 0.896,2.531 0.896,2.531 1.042,2.833 true 0.74,2.75 0.823,2.75 0.823,2.75 0.969,3.052 true 1.396,2.771 1.479,2.771 1.479,2.771 1.479,3.021 true 2.042,2.771 1.958,2.771 1.958,2.771 1.958,3.021 true 1.948,3.313 1.865,3.313 1.865,3.313 1.802,3.052 true 0.865,3.281 0.948,3.281 0.948,3.281 1.073,3.135 true 2.667,1.833 2.583,1.833 2.583,1.833 2.375,2.198 true 2.635,2.604 2.552,2.604 2.552,2.604 2.385,2.833 true 2.76,2.813 2.677,2.813 2.677,2.813 2.51,3.042 true 2.604,3.271 2.521,3.271 2.521,3.271 2.375,3.135 true 2.042,0.094 2.354,0.292 0.313,0.198 10 false *a 2.708,0.708 3.021,0.906 0.313,0.198 10 false *a 0.583,0.688 0.896,0.885 0.313,0.198 10 false *a 0.583,2.667 0.896,2.865 0.313,0.198 10 false *a 2,3.229 2.313,3.427 0.313,0.198 10 false *a 2.823,2.729 3.135,2.927 0.313,0.198 10 false *a 0.625,2.438 0.938,2.635 0.313,0.198 10 false *b 2.708,2.531 3.021,2.729 0.313,0.198 10 false *b 0.667,3.208 0.979,3.406 0.313,0.198 10 false *c 2.656,3.219 2.969,3.417 0.313,0.198 10 false *c 2.615,0.823 2.927,1.021 0.313,0.198 10 false *c 2.646,0.094 2.958,0.292 0.313,0.198 10 false *c 0.667,0.073 0.979,0.271 0.313,0.198 10 false *c 0.635,0.927 0.948,1.125 0.313,0.198 10 false *c 0.594,1.698 0.906,1.896 0.313,0.198 10 false *d 2.719,1.76 3.031,1.958 0.313,0.198 10 false *d 1.208,2.698 1.521,2.896 0.313,0.198 10 false *e 2.104,2.698 2.417,2.896 0.313,0.198 10 false *e 2.104,0.646 2.417,0.844 0.313,0.198 10 false *e 1.24,0.604 1.552,0.802 0.313,0.198 10 false *e
*a Marker A
*b Marker B
*c Marker E
*d Marker F
*e Marker G


Set the marker A, marker B, marker E, marker F and marker G so as to surround the vehicle as shown in the illustration.

Part Name Color Length Qty
Marker A White 800 mm (31.5 in.) 6
Marker B White 950 mm (37.4 in.) 2
Marker E White 350 mm (13.8 in.) 6
Marker F White 1000 mm (39.4 in.) 2
Marker G White 293 mm (11.5 in.) 4


ii.
E452016C01
0.76,1.177 0.844,1.177 0.844,1.177 1.052,1.396 true 0.771,1.729 0.854,1.729 0.854,1.729 1.063,1.948 true 2.667,1.271 2.583,1.271 2.583,1.271 2.375,1.51 true 2.677,1.667 2.594,1.667 2.594,1.667 2.385,1.906 true 0.583,1.094 0.896,1.292 0.313,0.198 10 false *a 0.573,1.646 0.885,1.844 0.313,0.198 10 false *a 2.708,1.208 3.021,1.406 0.313,0.198 10 false *a 2.719,1.594 3.031,1.792 0.313,0.198 10 false *a
*a Spacer J


Set the spacer J as shown in the illustration.

Part Name Color Length Qty
Spacer J Black 1000 mm (39.4 in.) 4


iii.
E452014C01
0.24,1.417 0.552,1.615 0.313,0.198 10 false *a 3.042,1.448 3.354,1.646 0.313,0.198 10 false *a 1.219,0.146 1.531,0.344 0.313,0.198 10 false *b 2.042,0.115 2.354,0.313 0.313,0.198 10 false *b 2.063,4.365 2.375,4.563 0.313,0.198 10 false *b 1.24,4.385 1.552,4.583 0.313,0.198 10 false *b
*a A (Spacer K and Spacer N)
*b B (Spacer P)


Combine with spacers and set at positions A and B to assemble the marker tool set.

A
Part Name Color Length Qty
Spacer K Black 500 mm (19.69 in.) 1
Spacer N Black 200 mm (7.87 in.) 1

HINT:

Create 2 sets and combine together.


B
Part Name Color Length Qty
Spacer P Black 107 mm (4.21 in.) 1

HINT:

Create 4 sets and combine together.



iv.

Set the marker H.

E452018C01
0.542,2.063 0.625,2.063 0.625,2.063 0.708,1.646 true 0.396,1.396 0.479,1.396 0.479,1.396 0.594,1.219 true 4.271,0.479 4.354,0.479 4.354,0.479 4.656,0.76 true 4.052,2.302 4.135,2.302 4.135,2.302 4.677,2.458 true 5.25,1.792 5.667,1.375 5.667,1.375 5.75,1.375 true 0.24,1.333 0.552,1.531 0.313,0.198 10 false A 0.385,1.979 0.698,2.177 0.313,0.198 10 false B 4.167,1.698 4.479,1.896 0.313,0.198 10 false *a 4.156,1.938 4.469,2.135 0.313,0.198 10 false *a 4.083,0.385 4.396,0.583 0.313,0.198 10 false *c 3.844,2.229 4.156,2.427 0.313,0.198 10 false *b 5.844,1.313 6.156,1.51 0.313,0.198 10 false *d
*a 100 mm (3.94 in.) *b Marker F
*c Marker H *d Distance from the front end of the marker F to the rear end of the marker H


Marker H Setting Positions Distance from the front end of the marker F to the rear end of the marker H
A 1600 mm (5.25 ft.)
B 400 mm (1.31 ft.)


v.

Align the position number on the marker F with the datum line as shown in the illustration.

NOTICE:

When aligning the marker F with the datum line, check that the string used for the datum line is not twisted or bent.


E452019C01
4.115,1.219 3.979,0.719 3.979,0.719 3.896,0.719 true 4.646,0.729 4.438,0.406 4.438,0.406 4.354,0.406 true 0.167,0.115 0.479,0.313 0.313,0.198 10 false *A 3.708,0.656 4.021,0.854 0.313,0.198 10 false *a 4.177,0.344 4.49,0.542 0.313,0.198 10 false *b
*A Example - -
*a Datum line *b Marker F


Marker F Position
4


vi.

Align the mark-off line of the marker A set at the front and back with the vehicle center line as shown in the illustration.

NOTICE:

When aligning the marker A with the vehicle center line, check that the string used for the vehicle center line is not twisted or bent.


E452020C01
4.813,0.948 4.896,0.948 4.896,0.948 4.979,1.24 true 5.458,0.781 5.646,0.458 5.646,0.458 5.729,0.458 true 5.479,1.375 5.75,1.906 5.75,1.906 5.833,1.906 true 4.615,0.875 4.927,1.073 0.313,0.198 10 false *a 5.771,0.375 6.083,0.573 0.313,0.198 10 false *c 5.917,1.844 6.229,2.042 0.313,0.198 10 false *b
*a Marker A *b Mark-off line
*c Vehicle center line - -



vii.

Check that the entire marker tool set is not distorted after the setting is completed. If there is any distortion, perform corrections so that it is straightened.

E452021


viii.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 13: SET SST (ADJUSTMENT OF ALL CAMERAS)


a.

At the right and left sides of the vehicle, extend strings (5) and (6) parallel to the vehicle center line (string (2)), and place SST.

SST
09870-52010  09870-52020  

i.
E439839C01
2.167,0.51 2.792,0.229 false 2.198,0.708 2.781,0.531 false 1.031,2.271 1.198,2.188 false 2.177,3.01 2.771,3.51 false 2.188,3.688 2.552,3.875 false 2.188,1.031 2.771,0.854 false 2.167,4.021 2.531,4.208 false 1.042,3.458 1.208,3.375 false 0.406,2.021 0.646,2.083 false 0.406,3.531 0.646,3.594 false 1.292,3.271 1.604,3.427 0.313,0.156 10 false *a 1.292,2.083 1.604,2.24 0.313,0.156 10 false *b 0.198,3.427 0.51,3.583 0.313,0.156 10 false *c 0.208,1.927 0.521,2.083 0.313,0.156 10 false *d 2.823,3.51 3.135,3.667 0.313,0.156 10 false *e 3.156,2.531 3.427,2.688 0.271,0.156 10 false *f 2.896,0.146 3.208,0.302 0.313,0.156 10 false *g 2.844,0.781 3.156,0.938 0.313,0.156 10 false *h 2.625,3.813 2.938,3.969 0.313,0.156 10 false *i 2.844,0.458 3.156,0.615 0.313,0.156 10 false *j 2.573,4.167 2.885,4.323 0.313,0.156 10 false *k
*a 1450 mm (4.76 ft.)
*b 3750 mm (12.3 ft.)
*c 2650 mm (8.69 ft.)
*d 6350 mm (20.83 ft.)
*e Datum Point
*f String 1
*g String 2
*h Mark E
*i Mark J
*j Mark W
*k Mark X


Mark the position on string (2) in front of the vehicle, 3750 mm (12.3 ft.) from the datum point. (Mark E)


ii.

Mark the position on string (2) in front of the vehicle, 6350 mm (20.83 ft.) from the datum point. (Mark W)


iii.

Mark the position on string (2) to the rear of the vehicle, 1450 mm (4.76 ft.) from the datum point. (Mark J)


iv.

Mark the position on string (2) to the rear of the vehicle, 2650 mm (8.69 ft.) from the datum point. (Mark X)


v.
E275619C01
1.302,1.135 1.698,1.01 false 1.719,3.031 2.365,3.146 false 2.156,1.281 2.365,1.094 2.365,1.094 2.531,1.094 false 2.156,0.833 2.365,0.646 2.365,0.646 2.531,0.646 false 2.583,0.563 2.833,0.76 0.25,0.198 10 false *a 2.583,1.052 2.76,1.208 0.177,0.156 10 false *a 2.406,3.104 2.615,3.302 0.208,0.198 10 false *b 1.104,1.083 1.323,1.25 0.219,0.167 10 false *c
*a 400 mm (1.31 ft.)
*b String 2
*c Mark E


Fix the ends of 2 strings (800 mm [2.62 ft.] long) at 2 positions 400 mm (1.31 ft.) from mark E as shown in the illustration.


vi.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks F and G)

E271119C06
1.771,0.719 1.146,0.521 false 2.135,0.885 2.604,0.635 false 1.156,1.083 1.469,0.896 false 5.615,0.885 6.094,0.677 false 1.802,1.073 1.188,1.417 false 5.208,0.656 5.677,0.323 false 5.75,1.396 5.24,1.104 false 3.948,1.083 4.26,0.896 false 4.625,1.083 4.938,0.896 false 2.135,2.479 2.771,2.542 false 4.938,2.51 5.573,2.573 false 0.969,0.438 1.156,0.615 0.188,0.177 10 false *a 2.656,0.542 2.885,0.719 0.229,0.177 10 false *c 0.969,1.042 1.177,1.198 0.208,0.156 10 false *d 6.146,0.594 6.354,0.75 0.208,0.156 10 false *e 1,1.365 1.208,1.521 0.208,0.156 10 false *a 5.719,0.24 5.896,0.396 0.177,0.156 10 false *a 5.802,1.354 6.031,1.521 0.229,0.167 10 false *a 4.438,1.052 4.625,1.219 0.188,0.167 10 false *c 3.771,1.031 3.969,1.198 0.198,0.167 10 false *d 2.823,2.479 3.042,2.635 0.219,0.156 10 false *b 5.625,2.51 5.844,2.698 0.219,0.188 10 false *b
*a 800 mm (2.62 ft.) String *b String 2
*c Mark E *d Mark F
*e Mark G - -



vii.
E287110C01
1.708,0.667 2.417,0.417 false 2.417,1.344 2.667,1.667 false 1.729,2.427 2.083,2.583 false 0.958,1.99 1.281,2.188 false 0.969,2.938 1.281,2.698 false 2.469,0.333 2.885,0.5 0.417,0.167 10 false *c 2.719,1.667 3.135,1.833 0.417,0.167 10 false *b 2.135,2.583 2.469,2.75 0.333,0.167 10 false *d 0.771,1.917 1.354,2.083 0.583,0.167 10 false *a 0.771,2.875 1.354,3.042 0.583,0.167 10 false *a
*a 400 mm (1.31 ft.)
*b String 1
*c String 2
*d Mark J


Fix the ends of 2 strings (800 mm [2.62 ft.]) at 2 positions 400 mm (1.31 ft.) from mark J as shown in the illustration.


viii.

Move the free ends of the 2 strings and mark the point where the ends meet. (Marks K and L)

E287111C01
6.156,1.031 6.396,0.656 false 5.542,1.906 5.781,2.125 false 6.51,1.719 6.208,1.906 false 5.24,2.115 5.052,2.396 false 4.854,1.906 4.604,2.073 false 2.063,1.615 1.885,1.708 false 2.229,1.906 2.51,2.083 false 5.292,1.656 5.01,1.438 false 1.531,1.906 1.26,2.073 false 1.927,2.073 2.26,2.323 false 5.521,0.604 4.844,0.354 false 0.99,1.031 0.74,0.656 false 1.542,0.563 2.24,0.313 false 0.583,0.542 1,0.708 0.417,0.167 10 false *b 2.302,0.219 2.719,0.385 0.417,0.167 10 false *c 4.635,0.271 5.052,0.438 0.417,0.167 10 false *c 6.385,0.521 6.802,0.688 0.417,0.167 10 false *b 1.094,2.052 1.427,2.219 0.333,0.167 10 false *d 4.427,2.031 4.76,2.198 0.333,0.167 10 false *f 2.552,2.063 2.885,2.229 0.333,0.167 10 false *e 6.542,1.635 6.875,1.802 0.333,0.167 10 false *e 5.792,2.146 6.125,2.313 0.333,0.167 10 false *d 4.802,1.323 5.719,1.49 0.917,0.167 10 false *a 2.115,1.542 3.031,1.708 0.917,0.167 10 false *a 2.271,2.365 3.188,2.531 0.917,0.167 10 false *a 4.958,2.438 5.875,2.604 0.917,0.167 10 false *a
*a 800 mm (2.62 ft.) String *b String 1
*c String 2 *d Mark J
*e Mark K *f Mark L



ix.
E439865C01
2.01,4.396 1.729,4.198 false 2.979,0.906 2.844,1.052 false 1.396,1.063 1.208,1.385 false 2.177,1.333 2.042,1.052 false 0.771,3.438 0.49,3.24 false 1.083,3.438 0.865,3.219 false 1.396,3.448 1.177,3.229 false 2.198,3.219 2.052,3.438 false 2.5,3.229 2.354,3.448 false 2.813,3.229 2.667,3.448 false 2.979,3.74 2.844,3.458 false 2.49,1.344 2.354,1.063 false 2.792,1.344 2.656,1.063 false 1.094,1.063 0.906,1.385 false 0.781,1.063 0.594,1.385 false 1.333,0.573 2.406,0.771 1.073,0.198 10 false *a 1.958,0.583 3.031,0.781 1.073,0.198 10 false *a 0.76,1.396 1.208,1.583 0.448,0.188 10 false *h 3.031,0.813 3.396,0.99 0.365,0.177 10 false *e 2.531,1.365 2.979,1.552 0.448,0.188 10 false *i 1.073,1.396 1.521,1.583 0.448,0.188 10 false *f 2.229,1.354 2.677,1.542 0.448,0.188 10 false *g 2.26,3.115 2.708,3.302 0.448,0.188 10 false *j 1.01,3.125 1.458,3.313 0.448,0.188 10 false *k 0.708,3.135 1.156,3.323 0.448,0.188 10 false *l 2.542,3.115 2.99,3.302 0.448,0.188 10 false *m 3.042,3.708 3.406,3.958 0.365,0.25 10 false *d 2.083,4.344 2.531,4.531 0.448,0.188 10 false *c 1.969,3.594 2.698,3.813 0.729,0.219 10 false *a 1.292,3.583 2.021,3.802 0.729,0.219 10 false *a 1.177,4.052 1.906,4.271 0.729,0.219 10 false *b 2.104,4.063 2.833,4.281 0.729,0.219 10 false *b 1.167,0.302 1.896,0.521 0.729,0.219 10 false *b 2.073,0.302 2.802,0.521 0.729,0.219 10 false *b 0.417,1.365 0.865,1.552 0.448,0.188 10 false *n 2.813,1.354 3.26,1.542 0.448,0.188 10 false *o 0.25,3.125 0.698,3.313 0.448,0.188 10 false *p 2.854,3.115 3.177,3.302 0.323,0.188 10 false *q
*a 1250 mm (4.1 ft.)
*b 1450 mm (4.76 ft.)
*c String 2
*d String 3
*e String 4
*f Mark F
*g Mark G
*h Mark H
*i Mark I
*j Mark K
*k Mark L
*l Mark M
*m Mark N
*n Mark AA
*o Mark AB
*p Mark AC
*q Mark AD


Secure strings (3) and (4) so that they pass through marks F, G, K and L as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



x.

Mark string (3), 1250 mm (4.1 ft.) to the left and right of the vehicle center line (string 2). (Marks H and I)


xi.

Mark string (3), 1450 mm (4.76 ft.) to the left and right of the vehicle center line (string 2). (Marks AA and AB)


xii.

Mark string (4), 1250 mm (4.1 ft.) to the left and right of the vehicle center line (string 2). (Marks M and N)


xiii.

Mark string (4), 1450 mm (4.76 ft.) to the left and right of the vehicle center line (string 2). (Marks AC and AD)


xiv.
E287132C02
1.094,0.688 1.292,0.271 false 2.302,0.667 2.688,0.177 false 2.604,1 2.875,0.677 false 2.625,1.375 2.302,1.01 false 0.781,1.385 1.104,1 false 0.458,3.26 0.698,3.583 false 0.771,4.031 1.094,3.594 false 1.552,3.833 1.708,3.74 false 2.646,3.948 2.313,3.594 false 2.635,2.646 2.469,2.958 false 1.344,0.198 1.802,0.396 0.458,0.198 10 false *e 2.75,0.104 3.208,0.302 0.458,0.198 10 false *f 2.938,0.604 3.396,0.802 0.458,0.198 10 false *c 2.688,1.396 3.146,1.594 0.458,0.198 10 false *h 0.625,1.417 1.083,1.615 0.458,0.198 10 false *g 0.313,3.104 0.771,3.302 0.458,0.198 10 false *d 0.646,4.073 1.104,4.271 0.458,0.198 10 false *i 1.375,3.875 1.833,4.073 0.458,0.198 10 false *b 2.667,4 3.125,4.198 0.458,0.198 10 false *j 2.729,2.573 3.188,2.771 0.458,0.198 10 false *a
*a String 1
*b String 2
*c String 3
*d String 4
*e String 5
*f String 6
*g Mark H
*h Mark I
*i Mark M
*j Mark N


Secure strings (5) and (6) so that they pass through marks H, M, I and N as shown in the illustration.

NOTICE:

When securing the string, check that there is no slack and the string is not twisted.



xv.
E439837C01
2.031,1.594 2.219,1.365 false 2.729,3.177 2.552,2.99 false 0.563,3.979 0.781,3.854 false 2.208,4 2.031,3.813 false 0.573,1.781 0.771,1.615 false 2.344,2.26 2.552,2.385 false 2.615,2.354 2.927,2.51 0.313,0.156 10 false *a 2.813,3.146 3.125,3.302 0.313,0.156 10 false *b 0.354,3.927 0.667,4.083 0.313,0.156 10 false *c 2.271,3.958 2.583,4.115 0.313,0.156 10 false *d 0.385,1.74 0.698,1.896 0.313,0.156 10 false *e 2.25,1.271 2.563,1.427 0.313,0.156 10 false *f
*a 2200 mm (7.22 ft.)
*b String 1
*c String 5
*d String 6
*e Mark Y
*f Mark Z


Make a mark on string (5) that is 2200 mm (7.22 ft.) from the reference line (string (1)) as shown in the illustration. (Mark Y)


xvi.

Make a mark on string (6) that is 2900 mm (9.51 ft.) from the reference line (string (1)) as shown in the illustration. (Mark Z)


xvii.

Align the center line of SST (television camera adjustment target) with marks AA and AB and place it parallel with string (3) as shown in the illustration.

NOTICE:

The vertical direction of SST (television camera adjustment target) differs depending on whether side setting or front, rear and corner setting is used.


E439708C02
4.208,2.083 4.531,1.948 false 5.01,4.802 4.906,4.698 false 2.479,3.323 2.802,3.188 false 2.406,1.948 2.792,2.094 false 2.052,1.177 2.448,1.438 false 1.406,4.688 1.76,4.313 false 2.917,0.479 3.51,0.969 false 5.438,5.469 5.25,5.26 true 1.427,1.167 1.677,1.438 false 3.531,0.771 3.917,0.385 false 5.333,4.708 5.198,4.844 true 4.969,1.115 5.177,0.969 true 5.438,1.115 5.333,1.01 false 4.927,0.344 5.094,0.563 true 5.385,0.26 5.177,0.354 true 5.167,5.458 4.896,5.594 true 4.188,3.177 4.5,3.302 false 4.438,1.625 4.531,1.438 false 3.5,4.813 3.24,5.042 false 2.458,4.323 2.031,4.729 false 4.521,4.323 4.396,4.531 false 3.969,0.313 4.385,0.479 0.417,0.167 10 false *e 5.469,5.469 6.052,5.635 0.583,0.167 10 false *b 6.229,1.552 6.813,1.719 0.583,0.167 10 false *a 1.219,4.625 1.552,4.792 0.333,0.167 10 false *g 1.26,1.083 1.594,1.25 0.333,0.167 10 false *f 2.292,3.271 2.625,3.438 0.333,0.167 10 false *h 4.615,1.833 4.885,2.052 0.271,0.219 10 false *m 2.208,1.865 2.542,2.031 0.333,0.167 10 false *l 3.052,5.01 3.385,5.177 0.333,0.167 10 false *k 2.729,0.365 3.063,0.531 0.333,0.167 10 false *j 4.573,3.24 4.906,3.406 0.333,0.167 10 false *i 5.427,0.167 6.01,0.333 0.583,0.167 10 false *d 5.375,4.615 5.875,4.781 0.5,0.167 10 false *c 6.24,3.49 6.823,3.656 0.583,0.167 10 false *a 4.719,4.615 5.302,4.781 0.583,0.167 10 false *a 0.542,3.479 1.125,3.646 0.583,0.167 10 false *a 0.531,1.542 1.115,1.708 0.583,0.167 10 false *a 5.5,1.063 6.083,1.229 0.583,0.167 10 false *a 5.281,2.167 5.865,2.333 0.583,0.167 10 false *a 1.563,2.177 2.146,2.344 0.583,0.167 10 false *a 4.781,1.063 5.281,1.229 0.5,0.167 10 false *c 4.75,0.26 5.333,0.427 0.583,0.167 10 false *b 4.719,5.542 5.302,5.708 0.583,0.167 10 false *d 1.875,4.719 2.208,4.885 0.333,0.167 10 false *p 4.302,4.552 4.635,4.719 0.333,0.167 10 false *q 1.875,1.083 2.208,1.25 0.333,0.167 10 false *n 4.323,1.635 4.573,1.802 0.25,0.167 10 false *o
*a SST (Television Camera Adjustment Target) *b SST (L Type Stand)
*c SST (Television Camera Adjustment Target) Center Line *d SST (L Type Stand) Center Line
*e String 2 *f String 3
*g String 4 *h String 5
*i String 6 *j Mark W
*k Mark X *l Mark Y
*m Mark Z *n Mark AA
*o Mark AB *p Mark AC
*q Mark AD - -



xviii.

Align the center line of SST (television camera adjustment target) with marks AC and AD and place it parallel with string (4) as shown in the illustration.


xix.

While the center line of SST (television camera adjustment target) is aligned with mark W and mark X, place string (2) so that it overlaps the center line of SST (L type stand) as shown in the illustration.


xx.

Align the center line of SST (television camera adjustment target) with mark Y and place it parallel with string (5) as shown in the illustration.


xxi.

Align the center line of SST (television camera adjustment target) with mark Z and place it parallel with string (6) as shown in the illustration.


xxii.

Perform the screen adjustment procedure (procedure 14).




PROCEDURE 14: CAMERA VIEW ADJUSTMENT (CALIBRATION)


a.

Enter diagnostic mode.


CAUTION:

The check must be performed with the ignition switch to ON (READY). Therefore, apply the parking brake, depress the brake pedal and move the shift position to P to ensure that the vehicle does not begin moving unexpectedly.



b.
E271944

Select "Function Check/Setting" from the "Service Menu" screen.


c.
E403245

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.



d.
E374234

Select "View Adjustment" on the "Mode Setting (*)" screen to display the adjustment screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



e.
E372765

After checking the screen, press the "Next" button on the "Signal Check (*)" screen.

HINT:
·

When "CHK" (red) is displayed, perform the inspections.

·

If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".




f.

Perform the view adjustment.

E444499C02
0.917,0.833 2.75,0.833 2.75,0.833 2.917,1 true 2,1.271 2.167,1.438 true 1.583,0.208 1.833,0.208 1.833,0.208 2.167,0.542 true 2.854,0.125 2.604,0.125 2.604,0.125 2.531,0.542 true 0.917,1.281 2.75,1.281 2.75,1.281 2.917,1.448 true 2,0.833 2.167,1 true 0.917,1.781 2.75,1.781 2.75,1.781 2.917,1.948 true 2,1.781 2.167,1.948 true 3.438,0.188 3.188,0.188 3.188,0.188 2.938,0.552 true 4.979,2.625 4.729,2.625 4.729,2.625 4.115,1.698 true 5.813,0.208 5.563,0.208 5.563,0.208 5.333,0.5 true 1.646,2.583 1.896,2.583 1.896,2.583 2.167,2.188 true 2.865,2.698 2.615,2.698 2.615,2.698 2.531,2.198 true 3.51,2.573 3.26,2.573 3.26,2.573 2.917,2.198 true 0.719,0.75 1.031,0.906 0.313,0.156 10 false *a 1.406,0.146 1.719,0.302 0.313,0.156 10 false *b 5.083,2.552 5.396,2.708 0.313,0.156 10 false *c 5.896,0.146 6.208,0.302 0.313,0.156 10 false *d 0.74,1.219 1.052,1.375 0.313,0.156 10 false *a 0.74,1.719 1.052,1.875 0.313,0.156 10 false *a 2.906,0.052 3.219,0.208 0.313,0.156 10 false *a 3.521,0.115 3.833,0.271 0.313,0.156 10 false *b 1.458,2.479 1.771,2.635 0.313,0.156 10 false *b 2.938,2.615 3.25,2.771 0.313,0.156 10 false *a 3.573,2.49 3.885,2.646 0.313,0.156 10 false *b
*a Red Frame (For Red Frame Judgment) *b Cross Check Marker (For Connection Judgment)
*c Detect Marker Button *d Camera Select Buttons


NOTICE:

The status before the operation can be restored by returning with the Back button and then entering this adjustment screen again.


HINT:

When you change all cameras, you may use All Camera Detect button.


i.

Check that the cross check markers displayed on the adjustment screen appear connected.

E271143

NOTICE:

Before checking the markers on the adjustment screen, ensure that the cross target bars have been placed correctly.



ii.

Check that the target bars do not protrude outside the red frames displayed on the adjustment screen.

E271144

NOTICE:

Before checking the Adjustment screen, ensure that the check markers have been placed correctly.




g.
E372775

When all adjustments are completed, press "OK".


h.

If data writing ends normally, "The view data writing was completed." is displayed.


i.

Press "OK".


j.


PROCEDURE 15: STEERING ANGLE SETTING


a.

Preparation for adjustment

i.

Park the vehicle with the steering wheel centered.

HINT:

Before parking the vehicle, be sure to move the vehicle forward and in reverse to check that the tires are facing straight ahead with the steering wheel centered.



ii.

Adjust the tire pressure to the specified value(s).



b.

Start the diagnostic mode.


CAUTION:

The following must be carried out with the ignition switch to ON (READY). Apply the parking brake, depress the brake pedal, check that the shift position is in P, and ensure that the vehicle is not moving.



c.
E271944

Select "Function Check/Setting" on the "Service Menu" screen.


d.
E403245

Select "Camera Setting" on the "Function Check/Setting I" screen.

NOTICE:

If the "Camera Setting" selection screen is not displayed, turn the ignition switch off and enter the diagnosis screen after turning the ignition switch to ON once again.



e.
E374234

Select "Steering Angle Setting" on the "Mode Setting (*)" screen to display the "Signal Check (*)" screen.

HINT:

To select a grayed out item, select and hold the item for 2 seconds or more.



f.
E372765

Select "Next" on the "Signal Check (*)" screen to display the "Steering Angle Setting D (*)" screen.

NOTICE:
·

If "CHK" (red) is displayed for an item on the Signal Check (*) screen, selecting "Next" will not change to the "Steering Angle Setting D (*)" screen.

·

Check the "Signal Check (*)" screen when "CHK" (red) is displayed for an item on the "Signal Check (*)" screen.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park)>DIAGNOSIS SYSTEM




g.

Adjust the steering angle

i.
E439843

Check that the steering wheel is centered (approximately +/- 5 degrees or less) and then select "Steering Center Memorize".


ii.

Turn the steering wheel fully to the left and fully to the right, and then press "Max Steering Angle Memorize". (Turning right and then left is OK)


iii.

When "Max Steering Angle Memorize" is selected, the steering angle setting values (steering neutral point and maximum steering angle) are stored and the system beeps for a long duration to notify the user that storing is complete before the "Mode Setting (*)" screen is displayed again.

HINT:
·

A beep will sound to confirm that the adjustment values have been stored.

·

If all signals are input normally, the "Mode Setting (*)" screen is displayed automatically after the maximum steering angle is stored.

·

If steering angle setting is incomplete, "OK" cannot be selected.

·

Even if no DTC is detected, a steering angle sensor malfunction may disable the use of "Max Steering Angle Memorize".

·

If selecting "Max Steering Angle Memorize" does not cause the adjustment value to be stored after adjusting the steering angle, replace the steering angle sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>REMOVAL





h.

i.

Confirm steering angle adjustment.

HINT:

If the steering angle has been adjusted, confirm the steering angle adjustment on the panoramic view and rear view screen or panoramic view and wide rear view screen after finishing diagnosis mode.



j.

Check on the panoramic view and rear view screen or panoramic view and wide rear view screen that the estimated course line moves until the steering wheel is fully turned to either the left or right.

HINT:

If the estimated course line stops moving before the steering wheel is fully turned to either the left or right, the steering angle adjustment values have not been stored correctly. In this case, perform "Steering Center Memorize" and "Max Steering Angle Memorize" again.




PROCEDURE 16: CHECK PARKING ASSIST LIGHT


Click hereADAS / AD>ADVANCED PARK>ADVANCED PARK>UTILITY