Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485736 PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park)  C162011  Rear Camera Circuit Short to Ground  


DESCRIPTION

This DTC is stored if the parking assist ECU determines that the input/output signal communication with the rear television camera assembly is abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C162011 Rear Camera Circuit Short to Ground Rear television camera assembly power supply malfunction
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E434590E16
1.646,0.448 2.104,0.646 0.458,0.198 10 false CB+ 1.531,1.24 1.99,1.438 0.458,0.198 10 false CGND 2.052,0.365 2.219,0.563 0.167,0.198 10 false 2 2.042,1.146 2.188,1.344 0.146,0.198 10 false 1 5.313,0.375 5.771,0.573 0.458,0.198 10 false 2 5.344,1.156 5.802,1.354 0.458,0.198 10 false 1 5.563,0.458 5.896,0.646 0.333,0.188 10 false CB+ 5.552,1.26 6.01,1.458 0.458,0.198 10 false CGND 1.167,1.594 1.49,1.781 0.323,0.188 10 false Y35 5.573,1.74 5.948,1.927 0.375,0.188 10 false O123 1.167,1.75 3.323,1.979 2.156,0.229 10 false Rear Television Camera Assembly 5.583,1.885 6.885,2.073 1.302,0.188 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)

Pre-procedure1

a.

Disconnect the O123 parking assist ECU connector.


b.

Disconnect the Y35 rear television camera assembly connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O123,Y35)Location & Routing

Click Connector(O123)Body>Floor Wire>Parking Assist ECU

Click Connector(Y35)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

O123-2 (CB+) - Y35-2 (CB+) Always Below 1 Ω
O123-1 (CGND) - Y35-1 (CGND) Always Below 1 Ω
O123 (CB+) or Y35-2 (CB+) - Body ground Always 10 kΩ or higher
O123-1 (CGND) or Y35-1 (CGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CB+, CGND)

Pre-procedure1

a.

Disconnect the Y35 rear television camera assembly.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(Y35)Location & Routing

Click Connector(Y35)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

Y35-1 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(Y35)Location & Routing

Click Connector(Y35)Body>No. 2 Back Door Wire>Rear Television Camera Assembly

Y35-2 (CB+) - Y35-1 (CGND) Ignition switch ON 7 to 8 V
Y35-2 (CB+) - Y35-1 (CGND) Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

NG