Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park) › from 2021.07
RM3700E _56 Audio / Visual / Telematics _093031 PARK ASSIST / MONITORING _0485736 PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park) C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM(w/ Advanced Park)  C168F11  Side Camera (Left) Circuit Short to Ground  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly LH to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
C168F11 Side Camera (Left) Circuit Short to Ground Side camera current malfunction (Left)
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH

·

Outer rear view mirror assembly LH (television camera wire LH)


Circumference Monitoring Camera Control Module A

WIRING DIAGRAM

E444532E01
2.292,1.708 4.573,2.26 2.281,0.552 10 false Outer Rear View Mirror Assembly LH (Television Camera Wire LH) 2.302,1.542 2.656,1.708 0.354,0.167 10 false LL1 0.5,1.542 0.771,1.729 0.271,0.188 10 false L15 0.479,1.719 1.938,2.031 1.458,0.313 10 false Side Television Camera Assembly LH 2.208,0.469 2.344,0.615 0.135,0.146 10 false 2 2.219,0.958 2.375,1.156 0.156,0.198 10 false 4 1.76,0.594 2.167,0.75 0.406,0.156 10 false CB+ 1.75,1.073 2.156,1.229 0.406,0.156 10 false GND 3.427,0.469 3.833,0.625 0.406,0.156 10 false LCB+ 3.938,0.479 4.073,0.625 0.135,0.146 10 false 2 3.417,0.938 3.823,1.094 0.406,0.156 10 false LGND 3.938,0.938 4.073,1.083 0.135,0.146 10 false 1 5.76,1.833 7.094,2.333 1.333,0.5 10 false Parking Assist ECU 5.76,1.667 6.188,1.833 0.427,0.167 10 false O122 5.958,0.604 6.365,0.76 0.406,0.156 10 false LCB+ 5.958,1.073 6.365,1.229 0.406,0.156 10 false LGND 5.698,0.49 5.885,0.656 0.188,0.167 10 false 2 5.708,0.948 5.896,1.115 0.188,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/ Advanced Park)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH))

Pre-procedure1

a.

Disconnect the O122 parking assist ECU connector.


b.

Disconnect the LL1 outer rear view mirror assembly LH (television camera wire LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
T ester Connection Condition Specified Condition
O122-2 (LCB+) - LL1-2 (LCB+) Always Below 1 Ω
O122-1 (LGND) - LL1-1 (LGND) Always Below 1 Ω
O122-2 (LCB+) or LL1-2 (LCB+) - Body ground Always 10 kΩ or higher
O122-1 (LGND) or LL1-1 (LGND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

2.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU

Pre-procedure1

a.

Disconnect the LL1 outer rear view mirror assembly LH (television camera wire LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(LL1)Location & Routing

Click Connector(LL1)Body>Front Door Wire LH / Television Camera Wire>Television Camera Wire and Front Door Wire LH

LL1-1 (LGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(LL1)Location & Routing

Click Connector(LL1)Body>Front Door Wire LH / Television Camera Wire>Television Camera Wire and Front Door Wire LH

LL1-2 (LCB+) - LL1-1 (LGND) Ignition switch ON 7 to 8 V
LL1-2 (LCB+) - LL1-1 (LGND) Ignition switch off Below 1 V


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH)

NG

3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH)

Pre-procedure1

a.
E434382C44
1.5,1.938 1.958,2.177 0.458,0.24 1.479,0.115 1.979,0.365 0.5,0.25 2.396,3.198 1.802,2.99 true 2.385,2.427 1.802,2.802 true 2.448,0.573 1.854,0.969 true 0.896,0.573 1.594,0.969 true 0.094,0.177 0.406,0.375 0.313,0.198 10 false *a 1.604,1.979 1.917,2.177 0.313,0.198 10 false L15 0.146,2.01 0.458,2.208 0.313,0.198 10 false *b 2.552,0.5 3.167,0.698 0.615,0.198 10 false LCB+ 0.469,0.5 1.083,0.698 0.615,0.198 10 false LGND 2.458,3.135 3.073,3.333 0.615,0.198 10 false GND 2.469,2.333 3.083,2.531 0.615,0.198 10 false CB+ 1.615,0.156 1.865,0.354 0.25,0.198 10 false LL1
*a Component without harness connected
(Outer Rear View Mirror Assembly LH (Television Camera Wire LH))
*b Front view of wire harness connector
(to Side Television Camera Assembly LH)


Disconnect the side television camera assembly LH connector.


b.

Disconnect the outer rear view mirror assembly LH (television camera wire LH) connector.


Procedure1

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(LL1,L15)Location & Routing

Click Connector(LL1)Body>Front Door Wire LH / Television Camera Wire>Television Camera Wire and Front Door Wire LH

Click Connector(L15)Body>Front Door Wire LH / Television Camera Wire>Side Television Camera Assembly LH

LL1-2 (LCB+) - L15-2 (CB+) Always Below 1 Ω
LL1-1 (LGND) - L15-4 (GND) Always Below 1 Ω
LL1-2 (LCB+) or L15-2 (CB+) - Body ground Always 10 kΩ or higher
LL1-1 (LGND) or L15-4 (GND) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



Post-procedure1

a.

None



OK

4.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH (TELEVISION CAMERA WIRE LH)

4.REPLACE SIDE TELEVISION CAMERA ASSEMBLY LH

NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 470

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 470

Result:
Result Proceed to
C168F11 is not output A
C168F11 is output B



A

END (SIDE TELEVISION CAMERA ASSEMBLY LH WAS DEFECTIVE)

B